Hey man. great project. When you took off the magnet section, there were drill holes for balancing on the outside. if you put them in the same place they were, the vibration will be gone/much less.
Лайк, подписка! 5 копеек вставлю. Замени флюс на твердую светлую канифоль. На лужение трех проводов обычно уходит 3 секунды. Провода зачищай перевернув на 180 градусов губы кусачек. Тогда они не соскальзывают, а снимают изоляцию.
Usually, this motor stayed in the original circuit board is less powerful than d.c brushed motor. Did it become powerful one after using your circuit board? I think you need to change to muti-strong magnetic pieces instead keep on using the original ring magnet!
Qual o inversor que vc uso e caseiro posso adquirir o esquema Tenho vários destes motores mas não funcionam com as Esc norma para aero modelos que são trifasisas também Tem como eu poder adquirir este drive
Ele não tá usando inversor man, não viu que a tomada fêmea deu 30 volts no multímetro?? Então não é corrente AC. A tomada com certeza tá ligada em bateria.
@@zees9669 girly, yer joke was not funny. it merely resembled one more, moronic question. if you want to tell a joke, go down to the pub. in many cases, written sarcasm just looks like stoopidity.
Es curioso cuando en ciertos momentos la alta velocidad de giro del motor, la imagen ondula por el efecto del campo magnetico giratorio a poca distancia de la camara
I tried by just guessing the quantity, distance apart, and polarity. I resoldered the coils for the "Y" format. It was a no go. I know the ESC worked too. I ran a magnet on the original magnet to find the number of magnets and polarity, but that may be the problem in the first place. Reconfiguring the coils means the magnetics probably need to be reconfigured as well.
All motor of printer and copier have hall sensor. and pcb on motor is its driver circuit. we just need to supply 24v 5v and signal pwm to the CLK pin and it will work. No need to buy ESC. because its driver circuit is very good. use sanken sla6024 power ic and lb18xx driver ic
*Join this channel to get access to perks:*
czcams.com/channels/WFbPzBb7dCyCWuBA-DBrMA.htmljoin
*Mr.Electron Patreon's Page* - www.patreon.com/mrelectron
*Hindi Channel* - www.youtube.com/@Mr.ElectronHindi
*Alternator Channel* - www.youtube.com/@mrelectron_alternator
*Watsapp Channel* - whatsapp.com/channel/0029VaQmmRaFCCoWOf7huh3G
*BUY Brushless Motor Controller* : bit.ly/2UV9Ybb
I need this brushless motor speed controller, but the link won't work
Good luck
i want one that plug into american wall socket for garage fun.please email if you find.
Mr Electron what is thr third wire used for
Never click a bitly.
Must have been one heck of a printer!
Good realising for motor and good satisfaction ideas. Class
Hey man. great project. When you took off the magnet section, there were drill holes for balancing on the outside. if you put them in the same place they were, the vibration will be gone/much less.
You're a genius man. Thanks so much for doing this!
Thank you sir
Great but the most important thing is the safety precaution .
From Kuwait🇰🇼
I like video thumbnail. It's attractive.👌
so nice power of a BLDC motor...
don't know about you, but i like the music finally someone that knows how to properly balance sounds.
It sounds like graduation music for nerds. 😂
What model of printer did this come from?
Keep up good work :)
7:42 reminds me one of ElectroBoom's video.
free4logix yay another person who watches him
Nice video good work, pls can you make a simple ESC driver using MOSFET, thanks alot
what kind of ESCa did you used for that kind of motor sir?
My brother, where did you get the engine?good job
excelente proyecto amigo te doy un 10!!!
Disculpa te consulto. Ese motor de que aparato se puede conseguir? En el caso que lo sepas. Muchas gracias.
@@thomytube1826 motor de CC de súper alta velocidad de 24 V de la impresora DEAD - Motores BLDC sin escobillas
Лайк, подписка! 5 копеек вставлю. Замени флюс на твердую светлую канифоль. На лужение трех проводов обычно уходит 3 секунды. Провода зачищай перевернув на 180 градусов губы кусачек. Тогда они не соскальзывают, а снимают изоляцию.
lol man you got it all figured out I respect that but you got to mount that motor(big or small) properly before testing the max rpm it can pull off
Thank you for the video.
Great video!!
Brother, What is this board that you connect the motor wires to?... thanks
Wow 23000 RPM
I have three same BLDC motors in my lab. your video good usually.
In which printer can I find such motor ?
@@yaminoshinn1473 I just purchased it from electronics scrap stalls which is open only weekly friday in my city.
Nice project 👌👌👌
Super projekt. Pozdrawiam serdecznie.
ist torsion strong enougth to used as spindle cnc?
Very good for a mini metal lathe 👍
Can I use this to generate cycle electricity?? You had made video for it
Ese variador de frecuencia que tienes te ayuda mucho
Уважуха автору видео не имея элементарных наборов отвёртки инструментов снять видео и набрать 2 млн просмотров это круто
на 3млн просмотров всего 17тыс лайков? представляю, сколько там дизлайков...
Thank you .
Can you show us this one generating power as an alternator.
Kev
nice video, can you please tell the back ground score
Parafusando o estator errado 6:34. Os fios deve ficar por baixo entre o estator e a placa de fixação.
Nice work👍👍👍🙂🤝
Спасибо большое за видео
Very good video 👍
you are newbie of soldering technic....but..you are still inventor..i.pround of you.
Amazing OMAR SUHAIB
Usually, this motor stayed in the original circuit board is less powerful than d.c brushed motor. Did it become powerful one after using your circuit board? I think you need to change to muti-strong magnetic pieces instead keep on using the original ring magnet!
What would be its toque?
No especificas sobre el circuito que usas para la conexión del motor...
What is the name of this majol
Nicely done
Any more information about type of printer to get this motor? Thanks doug
Hello
Where can one find such a motor
What is that circuit you connected to the motor at 7:31 ? Is it a potentiometer circuit to control the voltage?
How to get this type of variable circuit
Now... What are you going to use it for? Give a purpose or use for your findings! Neat video!
for fun
menginspirasi, boleh tahu itu bekas printer apa ?
I like this motor
farel sutanto ER b
what kind of motor driver you used?
thanks
Good, speed controller circuit Kong sa use kar Liya pata nhi chala
Паяльщик из тебя ещё тот!! Учись паять, не боися погреть место пайки, припой должен сам растечься, не надо припоем замазывать...
Он не электрик, он диайвайщик. А это совсем другое. Посмотрите какие у него бокорезы ржавые.
@@alro4505 ✋Тем более! Диайвайщик должен быть универсалом- все должен уметь! 😂😉
Qual o inversor que vc uso e caseiro posso adquirir o esquema
Tenho vários destes motores mas não funcionam com as Esc norma para aero modelos que são trifasisas também
Tem como eu poder adquirir este drive
Ele não tá usando inversor man, não viu que a tomada fêmea deu 30 volts no multímetro?? Então não é corrente AC. A tomada com certeza tá ligada em bateria.
Ginaldo Rui ele deixou o link na descrição do vídeo vc encontra esse drive no banggood
Very Good. Now can you run this three phase brushless motor without ESC?
BTW Good choice of background music.
@@RituSharma-wy4wm Sister I already knew. The question was a joke in itself. 😁
@@zees9669 girly, yer joke was not funny. it merely resembled one more, moronic question. if you want to tell a joke, go down to the pub. in many cases, written sarcasm just looks like stoopidity.
What type of driver you used to operate the motor
Good work
Bonjour, tu récupéres ce genre de moteur sur quoi ????? Merci
How much thrust can it generate ??
สุดยอด.. ทำได้.. 1800รอบ..
Es curioso cuando en ciertos momentos la alta velocidad de giro del motor, la imagen ondula por el efecto del campo magnetico giratorio a poca distancia de la camara
Saludos desde Ecuador
How I get a big one brussles motor tks
Nice, these motors aren't even that expensive to get!
guys, for the alternator speed dc device that car needs, which volume is it?
Eleven, it goes to eleven.. thats one more than max, next level man..
Just Buy a 50A esc And a servo tester
Super. Tech thank you sir
Where can I find such a controller please ?
Awesome! Thanks for all the anxiety haha.
Which printer are you use this motor
Can we make this as a generator for mini hydro power generation
IN THAT KIND OF ESC WAHT IS THE MAXIMUM POWER INPUT ? PLEASE REPLY THANKS
NOEL MELO thanks
I think he misunderstood the question. 😂
In any part of the printer specifically, I can find that engine
Ah ouais bravo champion big
Hi!
Where did you get that engine?
Xerox
6:36 Откручивать маленькие винты дрелью это что-то новенькое)
А то не видно, что это кто-то из наших?)) Ещё складная отвертка...
Нет, паять не умеет! Рукажоп!
Не судите его строго! Он из начинающих рукожопов!!! Как корабль назовёшь, так он и поплывёт!
How to make controller for 12v 5amp 16000rpm DC moter
Remote control airplane ESC (electronic speed controller) easy and cheap from hobby king
By mozfet z44
6:30 you mount the stator upside down 😆
🙄 yeah right 😄
What kind of drive you use for 3 terminal motor.
No hall sensor type
Can I feed it with 20 Amps (at its rated voltage) for like 3 seconds?
No. Because it will only draw the amperage that it requires. V/i = R gives you the wattage.
السلام عليكم ممكن استفسار الدائره التي تعمل علي تشغيل الماتور ما كيفية صناعتها ارجر الرد
Can you make a video about changing the weak magnetic strip inside the motor to strong neodymium magnets
I tried by just guessing the quantity, distance apart, and polarity. I resoldered the coils for the "Y" format. It was a no go. I know the ESC worked too.
I ran a magnet on the original magnet to find the number of magnets and polarity, but that may be the problem in the first place. Reconfiguring the coils means the magnetics probably need to be reconfigured as well.
Great sir
How can get drivers cercut from please tell me how get it,?
Great
can that motor also generate power mr. electron?
Que tipo de dispositivo utilizar electrónico esque tu usa para eso en la tarjeta dónde conecta los cables e tratado de Aser eso pero no epodido
where did you get the engine
great , thank share
Pl explain connection and amp requirements
Can i force it to 32v?
No hall sensor I see it, your output driver is 3phase right? Square wave or sine wave?
All motor of printer and copier have hall sensor. and pcb on motor is its driver circuit. we just need to supply 24v 5v and signal pwm to the CLK pin and it will work. No need to buy ESC. because its driver circuit is very good. use sanken sla6024 power ic and lb18xx driver ic
Sla6024 I think is too useful and difficult to find to be damaged with pliers 🤣
Fantastic
Why don't you get one of those gas Grill lighters to shrink those shrink wrap tubes.
Can you please show the connections and working of CD drive BLDC brushless motor....