MK1 RABBIT PICKUP TDI ENGINE MOUNT PREP FOR 02J TDI SWAP
Vložit
- čas přidán 28. 07. 2024
- in this episode i show you all necessary steps to install the proper mounts in order to prep your mk3 ahu tdi engine and 02a or 02j trans to install into your mk1 chassis
i also show you how to make your ahu convert to a single accessory belt system using a 12v vr6 water pump pulley
12v vr6 water pump pulley
021145255a
24v pulley will not work its offset hits water pump housing
belt for ahu single belt no ac no ps
6pk1040
all mk1 engine/trans mount inserts are installed with offset towards ground
tech53 02A/02J MK1 CHASSIS TRANSMISSION MOUNT KIT
tech-53.com/product/6th-gener...
mk1 oe type right side engine mount insert
171199214F
www.ecstuning.com/b-uro-parts...
mk1 oe type left side trans mount insert
both part numbers fit the trans mount or 5 speeds
www.ecstuning.com/b-meyle-par...
171199214H
171199214D
Like Comment Subscribe.
New Video Every Thursday And During The Weekend
IG Smiths_euro
support local shops
/ smiths_euro
4induktion.com/contact-us/
evwparts.com/
music
moog mightycarmods.com/collections... - Jak na to + styl
correction for the water pump pulley .. it's the power steering pulley off a 12v vr6. I'm getting things together to do this swap and looked over my 12v vr6 and found this out. Thanks for the video.
Ive never tried to see if that would fit.
I have only done the 12v water pump pulleys used in my area.
But in order to use it you have to have a few mm machined off the tdi crank pulley.
We had a lathe at the shop it was always the most common way for us to do it. And plenty of vr6 engines around to take the waterpump pulleys.
@@SmithsEuro Could You post the final diameter of the crank pulley? And did You take off metal on both the inside and outside rig? I have a friend with a lathe, it would be great to know how much to take off.
Usually has to be tested as you go.
Id say start with 2mm cut off so youll have 4mm total diameter cut off but per side will be 2mm that always faces the pulley.
🤘🏻🔥🤘🏻 truck will be on the road in no time at this rate!
I gotta get into editing mode to get the videos out. Its going to be a fun truck when its done.
As I worked in VW parts at one of the stealerships I was at before I was a tech there, the 'H' part as opposed to the 'D' is probably just superceded for either the application or it's an 'updated revision' of that bushing. You can check ETKA and type in the full number under the tab for applications and it'll tell you what it all fits. I'm sure anything mk1 chassis specific and possibly something older. The revisions happen more often on typical 'bulletin' parts like coilpacks... It may also be VAG's answer to an old part that became NLA. The mount brackets look nice although I do prefer poly or delrin. As long as it's got grease on the bushing and the proper sleeve/ washers they work well at helping the slop in the drivetrain. Prothane makes a poly insert for those mounts too, or you could make your own with some liquid. Good video man, great to see some progress on the caddy!👍😎
Looks like its and auto vs manual part number. The H is auto technically.
I thought about those inserts but was trying to keep rattles out.
Though in the end i had to get a solid lower rear mount due to the added power lol.
Thanks for still watching man! Appreciate it.
@@SmithsEuro
Yeah that makes sense about the P/N. Didn't think to mention that as a possibility for the part number breakdown. Yeah I remember running everything from hockey pucks, to homemade urethane mounts, using liquid urethane or delrin, the inserts, Vf engineering 3 mount set, BFI, EIP, and BBM solid aluminum front mounts, etc. I preferred the VF set or a combination of one of the solid aluminum front mounts, along with my own rear urethane one and a G60 trans mount. Seemed to be the best combination for my needs and the NVH never really bothered me that much. I built mostly a few different 1.8l/ 2.0l 16v's in either N/A, ITB, or boosted setups. Really miss some of those builds and the raw feeling of them. Your caddy is in exceptionally good shape. Can't wait to see this thing get built!😎👍👍
Youll have to build another one.
@@SmithsEuro
Yeah it's definitely a possibility if I could find the time/ money and an actual chassis to start with that isn't a rotten pile LMFAO 😏
iSpy a sticker of mine on the cart!
Got them everywhere lol
is there video of the drive by wire pedal install?
No I wasn’t happy with it. I used the mk3 pedal.
If i were to do it over again just buy any mk4 pedal and mk1-mk4 pedal adapter bracket.
Not worth the hassle of time i put into using them mk3 ahu pedal to save $100
Hello,
One question. Can you use original rear transmission mount or you need this aftermarket one?
Thanks in advance.
If you are converting to an 02a or 02j transmission you need a conversion mount.
If you are keeping your oem 020 5 spd or 4spd rabbit trans you can use the oem mount that came with that trans.
Did you use the original driveshafts from the caddy to the newer engine?
Depends what trans you use, original to mk1 reuse all that stuff.
I used the 02a so i got 16v scirocco axles and used washers to space them from the hubs.
90mm mk1 hubs need washers
100mm mk1 hubs do not
I have an original 1.6D with the original 4 speed gear box in my caddy mk1 but im swaping it for a AHU engine and a 02j/ctn gearbox. So im kind of trying to figure out what parts i Need and what parts i can reuse
The engine and gear box comes from a caddy II
Use everything i used.
For 02j trans youll probably have to swap the axle cups to 100mm 2.0/tdi ones to match the scirocco axles
With your car being 4spd youll need washers for then axles or they will lock up
Would this set up work for an ALH engine?
No, alh has an internal waterpump. You would need a custom made bracket engine side.
If using the 02a/02j trans these mounts would work.
If using the mk1 020 trans you reuse those mounts
Very cool to follow you, interesting videos you do👈🏻😀 regards from Denmark 🇩🇰 check out my mk 2 with 110hp TDI
Thanks for watching. What engine do you have in it?
I plan to put the truck on the dyno with the stock ahu turbo to have the baseline before going to the bigger turbo later on
@@SmithsEuro my engine came out of an seat Toledo from 1997, actually everything fits directly in golf mk2. Toledo frame is the same like golf mk2 in those models
Whats the engine code? There’s always differences from usa.
We have the ahu(which i have) and the aaz in the mk3 generation
The Engine code is AFN
Cool, looks like that one has a vnt turbo ours here are a normal wastegate style.
Yours also may have different injectors/mapping to get the extra power over my ahu.
Cool to see the differences