How to re-bind a Honeywell CM927 Thermostat to a BDR91 Wireless Relay Box | TheIntergasShop.co.uk
Vložit
- čas přidán 30. 01. 2018
- Richard walks through how to wirelessly pair/bind a Honeywell CMS927B1049 Wireless Room Thermostat to a BDR91A1000 Wireless Relay Box. When these were purchased together in a pack, they were known as a Honeywell CM927.
The same pairing procedure works with both CM921 and CM927. The BDR91 Wireless Relay Box pairing procedure is exactly the same when using a R8810A1018 OpenTherm Bridge or HC60NG/R6660D Wireless Relay Box instead of a BDR91 Wireless Relay Box.
If you have a faulty Honeywell CM721, CM727, CM921 or CM927 room thermostat, you can purchase a Pro Wireless Programmable Thermostat from The Intergas Shop website to replace these models - theintergasshop.co.uk/honeywe... - Jak na to + styl
Perfect video saved me a good few bob when a gas man came out and told me the thermostat was knackered and quoted £350 to replace. Trust no-one research and check everything yourself
Our thermostat disconnected from the boiler even the instructions were not this good! Everything was the opposite way! This was so simple to understand and very clear ...thank you for saving me from replacing the thermostat that's capable of doing its job just the instructions I had were completely incorrect...thank you again 😊
No problem at all... :)
Brilliant!!! Been looking everywhere for this. Can’t believe how hard it is to find a reset thermostat video. Thank you very much
Glad it helped! :)
Two years I’ve not had my thermostat working. Couldn’t thank you enough! Simple and easy fix after watching this!
A clear, short and concise video with no waffle and it works - thank you so much :-)
This video has probably saved me more £££ than anything I’ve ever watched. Thankyou!
Mine’s gone 100% blank even with new batteries.
Crap technology.
@@Keircomb181 in mine the contacts for the batteries had corroded, so it wasn't getting power
THANK YOU 🙂 THANK YOU 😊 THANK YOU 😉 I've had no heating for 3 days and my manual was no help at all....was going to call the repair man out and then I watched your video and it worked a treat ....now I 'm one happy lady again👍👍👍
Thank you Richard, we have been having real problems with our unit since coming back from holiday. The house temperature has not gone below 21 degrees for three days. In fact the temperature on our return was 24.5 . We had set the holiday mode to 12 *!? In fact even turning the boiler off didn’t make any difference.So let’s hope that this is all fixed now or a plumber is needed. Thanks again. Andrew
Brilliant, clear guide that saved me a decent wodge of £££. Was able to replace two broken control control units and pair them to the existing receivers. Thanks!
Thank you so much for this, instructions were next to no use, this worked first time!
Sweet Baby Jesus, thank you so much for this video.
Bought a house with these installed and no instructions to sort it.
Class video!
Glad it helped! 😎
Excellent help VT in simple format , thankyou
This video has saved me 3 or 4 times now. Many thanks for taking the time to make and post it. Your instructions work for my CM921 as well.
Thanks Mathew! Appreciate you taking the time to comment. 😎👍🏻
I just successfully paired a 2nd receiver. So I can now have an electric radiator coming on when the rest of the heating comes on!
Very handy in the kitchen where there is no easy way to plumb a normal radiator.
Forgot to add. Thank you for valuable and clear tutorial.
Thank you so much I even downloaded a pdf and followed the instructions bit it didn't work but following your video I manged to sort it am very grateful thank you
Great to hear!
Fantastic video! Fixed all the issues!
Just a shame it took so long to find you. Been ignoring the broken handset for over a year.
Glad it helped!
Tried this on a different model and it worked just the same, many thanks, great help.
Hi Richard, i can't thank you enough. I followed the instructions that came with the thermostat but got nowhere. Tried your method and bingo. The instructions must have been written on April 1st.
Glad it helped!
Can’t thank you enough for this straightforward and concise video.
Glad it was helpful!
Thanks for such an easy to follow guide Joe
Thank you thank you thank you! We have a 'CENTER' room thermostat which I couldn't find anything about. But I stumbled across your video and thought the controls on the Honeywell looked very similar though not totally identical, but near enough to try. It worked. So if anyone has a "CENTER EHE0200361 Programmable Room Thermostat" that has lost its binding to the base set (causing a red flashing light on the receiver at the boiler end) then just follow the instructions in this video. Just use a little common sense to recognize the slight difference in the appearance of the buttons on the CENTER remote thermostat. Thank you again!!
Good to hear, glad it worked.
Brilliant video. Thank you so much.
Seems like an unnecessarily complicated binding procedure, but great video, helped me this morning when connection was seemingly randomly lost
Cheers Richard, worked 1st time 👍
Omg thank you for this. Cant tell you the hassle you saved me by making this video. 😊
Worked perfectly thank you.
Mate you’re a legend!!
It s working! 😍😍Thank you!
That's great to hear! Please give the video a thumbs up if it has helped you! :)
Can’t thank you enough, you have made it so easy for me and saved me so many £££.. thank you
Glad it helped! 👍🏻
Thankyou clear and concise much appreciated 👍
Worked perfectly....thanks!
You're welcome!
This video saved me, thank you
THANK YOU, JUST SAVED ME £100 LEGEND!!
Perfect ! Thank you !!!!!
Top man thank u for putting this up
No problem 👍
Thank you for this very straightforward to the point video much appreciated and got me right out the s***
You're welcome!
Thanks very helpful
Thank you really appreciate this video has saved me some money too....
Thank you
Glad it helped! :)
Hi Richard really good and simple video,my thermostat is a centre and looks similar to that one,is the concept all the same with them,thank you
Have a look at the pro series thermostat video we have on the channel, as this should be the same as the centre brand one to bind.
Thanks a lot 😊 life saver!
You're welcome! :)
Not the same model but this just worked perfectly, thank you!
You're welcome!
Excellent thankyou
Thank you so much !
You're welcome!
Awesome. Saved me £160
Thank you!!
Hi Richard I've used your video many times before. This time tho my CM921 will go into binding menu. Do you have any ideas?
Faulty slider maybe? Have a look at this if you need a replacement - theintergasshop.co.uk/home/99-cms927-7-day-wireless-programmable-room-thermostat-cms927b1049.html
Magic.
Do i have to leave the box (with the little green light) on constantly? And turn the heating off by the other part?
The thermostat is the only thing you can control the heating system with. The relay box with the green light responds to the demands of the thermostat and you shouldn’t have to touch this unless the thermostat breaks.
Thank you 🙏
You’re welcome 😊
thanks a lot !
I’ve done this now and it’s put my heating back on but one light on the receiver is steady green and the light below it is flashing red any advice? Honeywell cm921
Did you 100% press and hold the button for a full 15+ seconds initially? If not, it could be indicating you have filled up the 4x memory slots (i.e. bound the thermostat to the BDR91 four times). Give Resideo technical support on 0300 130 1299 if you require further support.
Hi Richard I used this video a few times before on my centre controller no problem,this time my controller will work manually but when I set the time it does not work,I have temp set to 21 starting temp in room 18,can’t understand why,any help I’d be very grateful thanks
Might not be the thermostat if the relay box is turned off (green light off). Possibly another component failed?
Hi Richard.
The green light is on and the thermostat has the flame on. I hear a click as if it's tring to come on, but still not working
What is the relay attached to? A green light plus relay clicking normally indicates that the BRR91 is fine? It could be something else faulty or maybe the relay itself. If you need a replacement relay, we sell an OEM replacement here at about half the cost - theintergasshop.co.uk/heating-controls/28-honeywell-bdr91-wireless-relay-box.html
My CM927 controller won't go into binding mode when I press the 3 buttons simultaneously... How can I fix this? Thanks!
Need to make sure 100% the slider is in the off position and then it will work (as long as the buttons are not faulty and it is a wireless version).
Hi Richard, I have a honeywell CM61ng been fine for 20yrs but discovered it doesn't like red wine lol. Got one from ebay and followed instructions for CM927 until got to 'ok' button that I don't have, HELP please
Sounds like you don't have a CMS927 of you don't have the OK button? What is the model code you bought?
Hi there, I have this unit, and I am trying to bind to my control unit, which isn't exactly the same as the one in your video ( I don't know/can't see an identifying no.)
On pressing the up and down buttons along with the left button, nothing on my display changes. Can you suggest a cause of this, and a possible remedy? Thanks for an informative video.
Without knowing the model you have I can't help sorry.
Hi Richard, I am not able to get the thermostat to go into the binding mode as much as I press. I changed the batteries and it is still not happening. The slider is off. I followed the instructions
Same here any joy ?
Ditto
You need to confirm all the buttons you need to press in the video are working. If they are and the slider is 100% in the 'off' position then the product may need to be replaced if it won't go into bind mode. This thermostat is a good replacement and will pair with any existing BDR91 - theintergasshop.co.uk/home/99-cms927-7-day-wireless-programmable-room-thermostat-cms927b1049.html
I have tried pressing the three buttons at the start but I don’t get the inst co come up what can I do?
Is the slider 100% in the ‘OFF’ position? The 3 button press won’t work unless it is.
Hi I press the 3 buttons and nothing happens i dont get the binding display i have replaced the batteries ?
If the product is fully functional and you follow the video correctly it should work. If the product is faulty or you don’t follow the video correctly then it won’t work I’m afraid.
My Honeywell 927 room thermostat screen shows broken numbers and not responding to timings. The clock keeps bad timing and the settings jump from eg 17 to 19 ( not displaying 18) . It is quite old ,so is it irreparable ?
If you have a faulty CM927 then this is a decent replacement for it, as long as you have a BDR91 - theintergasshop.co.uk/home/99-cms927-7-day-wireless-programmable-room-thermostat-cms927b1049.html
Hi Richard is there a way to pair a bdr91a with a new Honeywell T3
Unfortunately not. The T3 Series, uses a different RF protocol to the CM927. The only compatible thermostat for a BDR91A we know of is this one - theintergasshop.co.uk/home/99-cms927-7-day-wireless-programmable-room-thermostat-cms927b1049.html
Hi mine won't let me chance the temperature... what to do?
Might need a replacement? Check out this video - czcams.com/video/mlh4-WILyUo/video.htmlsi=ZzgC7-xF6HXwI8g6
I press the three buttons and it does not go into the binding menu.
As long as the thermostat is a CM921/CM921 and the slider is off it should work, unless of course the thermostat is faulty?
I tried this, once the boiler started for some minutes, but then again went off...
Unfortunately, the video only shows how to bind them back together. If there are further problems, maybe see if turning the power off to the BDR91 for 5 minutes and back on helps?
Why would this make of thermostat keep turning its self up really hight please
No idea sorry Gemma. Only reason the temperature should change is if it’s programmed to do this. Possibly faulty?
Great video thank you life saver
Glad it helped! :)
HELP i can't even get the control unit to go into link mode, any help will be gratefully received
It might be faulty. Technical support is on 0300 130 1299 if you need it.
@@MWPHS thanks
Can a 727 program box bind to a 927 receiver?
Cheers
Yes, a CM720 series can bind in as they use the same receiver.
@@MWPHS absolute gent 👍🏻👍🏻
@@the-real-angus-young no problem.