Had same problem with ford 2000, fixed it today. There are few Ford tractors in Poland and even less information about them. I really like them, I also have a Ford 3000 :) Thank you for the movie and the opportunity to see what it looks like inside before the repair . Greetings from Poland
I pulled the top off my tractor yesterday. At the return line on the top some fell off into the bottom. It looked like a o ring or a washer it happened so fast I couldn’t tell what it was. In the video I seen you put it back on after you pulled the line out. What was it and do I need to. Taking it apart further to find it or do I just need to replace it and leave it in.
I have a 70s ford 3600 and the lift stopped working. I opened a bolt on top and it doesn't have hardly any pressure. Only a bit of oil came out . It seemed airated but the oil on the dipstick is clean . Does that sound like I need a new pump? Or should I look elsewhere?
I like your video I have a three thousand that was blowing the 1/2 line out of the pump and bottom by the transmission I replaced the line and the original fittings the cheaper aftermarket wouldn't hold but the hydraulics are not working we blead the pump but still doesn't lifting any help would be appreciated
Ray, I had/have the same problem with my 3000. I eventually used clamps to hold the 1/2 inch tube in to the socket. I made the clamps from light metal. The original tube used e steel washer similar to a Belleville washer that was interference on the tube. The nut would push on the washer ant the washer would grip the tube hand hold it in. The rubber sea was the same as you get with the new kit. The copper washer will not grip the tube and hold it in place. I hope to find a thin steel washer to return my tractor to original and remove the clamps. But they do work.
Ray our old 3000 started doing the same thing. This was many years ago. I tried replacing the nut that has the packing in it. Only to have it blow out again after a few hundred hours. Next, I replaced the hydraulic line that goes from the pump down to the side of the transmission.. It quickly blew out agin. Next I made a U bolt type clamp to hold the line in. That worked to keep the line from blowing completely out of the pump. Pumping all the oil out of the transmission before you could shut it down. BUT, after a while it started just leaking. Quickly got to bad to tolerate. The next thing was to use some 1/2 scrap hydraulic lines and fittings off a cotton picker. These lines had the flair type connections. I believed at this point. The rubber packing in the Ford nut was fauilty. Using Ford's nut. That by now I had several of. I removed the packing. Cut a JIC type fitting from the cotton picker in half. Very carefully welded it to the nut. Cut the steel hydraulic line. Welded part of the tube that had the flair to the Ford line. About 3". Part of the line had to be heated and reshape. It was tedious work. But this fix lasted many year. 2-3 more thousand hours until we sold the tractor. The inability of Ford to provide a proper "fix" for this and other problems. We had with our Ford's. Was a major deciding factor in us moving to John Deere tractors. We also had a neighbor with a 3000. He had the exact same problem with his tractor.
@@rogercarrico4975 John Deere beats Ford in many ways ever wonder why John Deere still in business and Ford tractors are not. I own a Ford 4000 and I'm having issues. Working on the 4000 is always been a pain.
@@SoybeanFarmer3300 We traded our 3000 for a JD 5300. Granted it has 10 or more so HP. But just so much better made tractor. That great power steering, hydraulic brakes, more comfortable seat. Been really pleased with it.
Tamiri yapılan ford 3000 modeli kaçtır. Bizim de 1973 modeli var. Hidroliği tamir yapılsa da çabuk arızalanıyor. Ford 3000 e ford 3600 hidroliği uyar mı? İzmir/TÜRKİYE
I'm assuming your referring to the orings in the lift assemblies. You are right. I didn't expect this video to be as popular as it has turned out to be or I likely would have.
How similar is this to a Ford 4610 tractor setup. I think I have a pick up tube cracked but Im not sure if I can base the removal process from this specific setup.
@@dodgemechanic tractor hydraulic pump looses pressure going up hill only. Down hill everything works fine. Fluid level is fine system is primed. Filter is changed also.
Eu preciso de uma ajuda estou com um Forde desse aqui desmontado não está funcionando o hidráulico dele eu desmotei uma tampa debaixo e tem uma válvula tem um anél uma cavidade e depois uma parte redonda aparte redonda está com os furos livre mas aparte dá cavidade está tampado com souda será que o gato está aí
Had same problem with ford 2000, fixed it today. There are few Ford tractors in Poland and even less information about them. I really like them, I also have a Ford 3000 :) Thank you for the movie and the opportunity to see what it looks like inside before the repair .
Greetings from Poland
You Sir are a manly man! I used an overhead chain hoist to lift mine and awkward is an understatement. Thanks for posting this. :)
I agree with you 💯. I done my 4610 by myself.
Good video Sir. Done a lot of theses for years and happy to retirement but still doing them Lololo
Good overview. Thanks!
It was very helpful to show you how to tighten with a torque wrench.
I pulled the top off my tractor yesterday. At the return line on the top some fell off into the bottom. It looked like a o ring or a washer it happened so fast I couldn’t tell what it was. In the video I seen you put it back on after you pulled the line out. What was it and do I need to. Taking it apart further to find it or do I just need to replace it and leave it in.
I have loosened my flow control valve to a point where it will not tighten back up. Im guessing I will have to take this apart like you did.
Lllllllllllllllll
I
I have a 70s ford 3600 and the lift stopped working. I opened a bolt on top and it doesn't have hardly any pressure. Only a bit of oil came out . It seemed airated but the oil on the dipstick is clean . Does that sound like I need a new pump? Or should I look elsewhere?
look inside at the pickup tube and o-rings it may have dropped if the bracket broke
I have a 3000. Mine has two baffles inside that keeps the fluid on the gears. I noticed you don't have that. Mine is also a British model.
I like your video I have a three thousand that was blowing the 1/2 line out of the pump and bottom by the transmission I replaced the line and the original fittings the cheaper aftermarket wouldn't hold but the hydraulics are not working we blead the pump but still doesn't lifting any help would be appreciated
Ray, I had/have the same problem with my 3000. I eventually used clamps to hold the 1/2 inch tube in to the socket. I made the clamps from light metal. The original tube used e steel washer similar to a Belleville washer that was interference on the tube. The nut would push on the washer ant the washer would grip the tube hand hold it in. The rubber sea was the same as you get with the new kit. The copper washer will not grip the tube and hold it in place. I hope to find a thin steel washer to return my tractor to original and remove the clamps. But they do work.
Ray our old 3000 started doing the same thing. This was many years ago. I tried replacing the nut that has the packing in it. Only to have it blow out again after a few hundred hours. Next, I replaced the hydraulic line that goes from the pump down to the side of the transmission.. It quickly blew out agin. Next I made a U bolt type clamp to hold the line in. That worked to keep the line from blowing completely out of the pump. Pumping all the oil out of the transmission before you could shut it down. BUT, after a while it started just leaking. Quickly got to bad to tolerate. The next thing was to use some 1/2 scrap hydraulic lines and fittings off a cotton picker. These lines had the flair type connections. I believed at this point. The rubber packing in the Ford nut was fauilty. Using Ford's nut. That by now I had several of. I removed the packing. Cut a JIC type fitting from the cotton picker in half. Very carefully welded it to the nut. Cut the steel hydraulic line. Welded part of the tube that had the flair to the Ford line. About 3". Part of the line had to be heated and reshape. It was tedious work. But this fix lasted many year. 2-3 more thousand hours until we sold the tractor. The inability of Ford to provide a proper "fix" for this and other problems. We had with our Ford's. Was a major deciding factor in us moving to John Deere tractors. We also had a neighbor with a 3000. He had the exact same problem with his tractor.
@@rogercarrico4975 John Deere beats Ford in many ways ever wonder why John Deere still in business and Ford tractors are not. I own a Ford 4000 and I'm having issues. Working on the 4000 is always been a pain.
@@SoybeanFarmer3300 We traded our 3000 for a JD 5300. Granted it has 10 or more so HP. But just so much better made tractor. That great power steering, hydraulic brakes, more comfortable seat. Been really pleased with it.
@@SoybeanFarmer3300 but to repair a J D pump you have to split the tractor--SUCKS as it runs off the drive line
Tamiri yapılan ford 3000 modeli kaçtır. Bizim de 1973 modeli var. Hidroliği tamir yapılsa da çabuk arızalanıyor. Ford 3000 e ford 3600 hidroliği uyar mı? İzmir/TÜRKİYE
You should have shown the process of resealing the lift cover.
I'm assuming your referring to the orings in the lift assemblies. You are right. I didn't expect this video to be as popular as it has turned out to be or I likely would have.
Which oil for use
Boa noite eu sou mecânico diesel dê caminhão um sitiante
so you didn't do the lift cylinder?
Saludos desde México nós podrían esplicar en español
Não sei falar inglês entendo um pouco em castelhano
How similar is this to a Ford 4610 tractor setup. I think I have a pick up tube cracked but Im not sure if I can base the removal process from this specific setup.
4610 has a pump in rear end housing under right floor board
@@dodgemechanic how difficult is it to repair a pick up tube on it.
@@tavo6881 how do you even know thats the problem
@@dodgemechanic tractor hydraulic pump looses pressure going up hill only. Down hill everything works fine. Fluid level is fine system is primed. Filter is changed also.
Para un massey Ferguson
No engine lift.
Great guy huge horn
What oil to use it system of link cylinder of ford tractor
This one is running a universal tractor hydraulic oil. There are several options but I stayed with what has been run in this tractor for many years.
S
fort 3000 hidrolik kaldırmıyor
Mi tractor esta lento por los idraulico
Eu preciso de uma ajuda estou com um Forde desse aqui desmontado não está funcionando o hidráulico dele eu desmotei uma tampa debaixo e tem uma válvula tem um anél uma cavidade e depois uma parte redonda aparte redonda está com os furos livre mas aparte dá cavidade está tampado com souda será que o gato está aí
kastellano
Cut some bolt heads off for guides
The story does not say why he pulled the cover in the first place since he did not do anything to it. Boredom perhaps.
He said it in the first 10 seconds
@@jaredellison3720 sorry i missed that
ممكن بالعربيه