Experimental Hang Glider Project | Deneysel Yelken Kanat Projesi #1

EDİT: 03:57 TIME "FIBERCLASS" = FIBER GLASS PİPE
yelkenkanatprojesi.wordpress....
gnuFloater Hang Glider DXF Drawings by ;
www.laboratoridenvol.com/lehan...
Experimental Handmade Hang Glider 3D Model by;
Emre Civelekoğlu | yelkenkanatprojesi.wordpress....

[@emrecivelekoglu37]

Turkish: Bu proje hakkında daha fazla bilgi için lütfen CZcams profilimde yer alan Topluluk sekmesine bakın.
English: For more information about this project, please see the Community tab on my CZcams profile.

[@mahamed3208]

Thank you very much for your ❤😊

[@messaoud.ben.mohamed]

جميل جميل ورائع

[@AzadAmeen]

Really, your work is great, but we need more clarification, especially the measurements. Thank you very much

[@ericoschmitt]

How do you expect the weight to shift if the trike base is attached to the base bar?

[@emrecivelekoglu37]

Thank you for your comment. First of all, I must admit that the design in this video is very old and there are many mistakes. When I first started developing this Hang Glider, I was a very, very newbie.
As for the question you asked, the weight shift in this design was planned as in the video below. From 19 seconds.
czcams.com/video/pa61ZeByFuM/video.html
I will answer the questions you wrote in other videos from the comments of that video.

[@osninielsen6933]

Boa tarde , como obter as medidas p/ esse projeto ?

[@phakly8366]

Hello ❤ what is software you use for this project?

[@emrecivelekoglu37]

SketchUp :)

[@rmu3212]

umarım başarırsın

[@sollsern2643]

There is a tutorial yo make one of this ?

[@emrecivelekoglu37]

I haven't gotten to the build phase yet, because I want to make sure everything is alright.
If I am convinced that the design is completely finished, I will start the construction. You will be able to watch the construction process on CZcams.

[@David-ls1hw]

Hola
¿Tienes los planos en PDF con medidas?

[@ericoschmitt]

This is an unfinished and untested sketch of a project, with no sail cut design yet made (arguably the most important aspect of handling and safety), so I wouldn't recommend trying to build. Even with plans, it would be tricky to source individual tubes to build a single glider, and probably cheaper to just buy one made at a factory.

[@truckdriver592]

to save fuel, it could be slimmer. The wings are too wide. Don't use too many frames to make it easier to control. If it's slim, it can fly anywhere. No need to use motorbikes and planes to go anywhere.

[@mustafakucukerdem4593]

Selamlar ölçüleri nasıl alabiliriz yapmak istesekustam

[@emrecivelekoglu37]

Aleyküm Selam, daha tasarımı oturtamadım be ustam. Uzaktan Kumandalı küçük bir versiyonunu yapmaya çalışıyorum test için(küçük prototip), ama bayağı uğraştırıyor.
Ayrıca bu videodaki tasarım çok eski yenisi en son yüklediğim.
Ama kabaca bir ölçü vermek gerekirse CZcams profilimdeki 'Topluluk' sekmesine bakın.

[@emrecivelekoglu37]

Ayrıca sadece ölçüler işinize yaramayacaktır, bunun Washout derecesi var kanat profili yani batenleri var ağırlık merkezinin dengesi var varoğlu var.
Sadece bu ölçülerle yapmaya kalkarsanız malzemeler elinizde kalır.

[@emrecivelekoglu37]

Kısacası proje hazır değil, henüz.

[@rmu3212]

uygulamanın ismi nedir

[@emrecivelekoglu37]

Uygulama SketchUp 3D modelleme yazılımı, 3D model daha geliştirilme aşamasında. :)

[@jomeralikha514]

ভাইজান মেজার দিয়ে দিন

[@IbrahimHossin-jt1wz]

কোন দেশ,,