hey man, you`ve put the 6 studs the other way around, the flat side must be on the inside of the holes and the round side is outside. For the rest, you did everything well. keep up the good work.
А ведь в этой Makita DDF484 патрон сидит на двух подшипниках, что однозначно лучше чем в Makita DDF487 где патрон сидит на одном подшипнике + 1 втулка. Там имеется небольшой люфт патрона даже у нового инструмента.
hola,muy buen video,sin musica ni molestiasy muy claro ,a un buen manitas incluso no ace falta ningun comentario,mis gran respetos y agradicimiento😉👏👍gracias
Hi, i searched most of the CZcams videos. but in your channel, i could find out about those two tiny steel stumps @11:15 how to put them or where they needed to be, i find it helpful from your video, but i find those tiny steel stumps to be in a bizarre place to be. Didn't make any sense to me. Iam a DIYER 👍👍👍👍 and prefer to do things on my own whenever I can.
hey man, you`ve put the 6 studs the other way around, the flat side must be on the inside of the holes and the round side is outside. For the rest, you did everything well. keep up the good work.
А ведь в этой Makita DDF484 патрон сидит на двух подшипниках, что однозначно лучше чем в Makita DDF487 где патрон сидит на одном подшипнике + 1 втулка. Там имеется небольшой люфт патрона даже у нового инструмента.
+ здесь передняя часть редуктора действительно металлическая, тогда как у 487 металлическая только декоративная накладка
@@goodtoshiа зачем 487 вообще металлический редуктор?) Там 40Нм)))) другие шурики в пластике живут и ничего, пластик справляется)
hola,muy buen video,sin musica ni molestiasy muy claro ,a un buen manitas incluso no ace falta ningun comentario,mis gran respetos y agradicimiento😉👏👍gracias
你好,我的朋友,谢谢你的视频非常棒,请继续加油,但是,视频中有几个小问题,第一是弹簧卡子可能你用力过度,容易导致使用过程中跳出卡槽,第二是六个圆头柱形销钉安装反了,平的应该放下面,圆头在上面。第三是所有旋转的地方和齿轮接触的地方,都需要涂抹少量润滑油脂,会减少磨损和噪音的,以上只是个人的意见,请不要见怪。
Me ayudo mucho tu video gracias
МОЛОДЧИК 🫵💪☝️
Good vid, its help me ..thanks
Благодарю, помог.
❤ 덕분에 조립했어요
Thank you very mutch
I saw you installed a 14,4 volt battery in this 18 volt Makita drill. Does this work well or do you have issues?
A little less power but it works fine. Good luck
Je kunt zien dat de monteur Vakbekwaam is. De eigenaar van de Makita kan er weer jaren tegen aan 👍
Hi, i searched most of the CZcams videos. but in your channel, i could find out about those two tiny steel stumps @11:15 how to put them or where they needed to be, i find it helpful from your video, but i find those tiny steel stumps to be in a bizarre place to be. Didn't make any sense to me. Iam a DIYER 👍👍👍👍 and prefer to do things on my own whenever I can.
Hello! Do you have size of that ball bearing which you changed? I have same problem, and i like order ball bearing before disassembling the machine.
This is size of the old bearing for the DDf484:
inside: 7,8mm
outside: 15,9mm
Thickness: 4,9mm
Good luck
Respekt
What grease do you use for the gears? lithium or graphite or molybdenum?
Normal bearing grease. Good luck
Замученый дивайс. Даже смазки нет! Убили!
buy a air compressor
спереди 2 подшипника или втулка есть?
люди говорят 2 подшипника.