Nice work. Can't wait to get comfortable using the new template. BTW, the new BBE is PWA now, so I guess we dont need to update anymore! Betaflight configurator is next 🤞
Having the motor rpm measurements is amazing! Those are pretty constand for a given prop and after adjusting for battery sag. Meaning you can actualy do some identification and automated optimal tuning based on them. Won't do much for ppl who already tuned their quad, but might allow for better "default" tunes if they are based on this knowledge.
Greatness! Do you plan on creating a controller script much like Brian White (PIDToolbox) patreons can get that would give you consistent tuning flights as well?
Ok maybe ill go back to betaflight and try this. Do from scratch. No clue what happened my 10" started oscillating crazy lot. Hot motors at low throttle going down. Or pulling out dive. But pid were perfect before. Props look fine. INAV short angle mode test seemed perfect though
@chrisbee5481 first thing I thought. But wasn't. Checked even stack screws. Found antenna getting loose but didn't fix it. I only thing left is I swap props.
I recently built a 10 inch bird. I used 3115 900 kv T-motors with HQ 10x4.5x3 props. Are these motors sufficient in your opinion or should I try to find bigger motors?
I have same build same motors. Motors plenty big enough. Though I touch something on betaflight and started having huge oscillation at low throttle or pulling out dive. Couldn't figure out what even going back to old pids. Then old diff then old dump. I ended up just putting inav in and seem like it didn't do it. Idk. Can't figure out what I could of touched in betaflight.
How u like the 10x4.5x3? Suppose to be more efficient even though they r heavier. I have gemfan 10x5x3 on right now but I have 10x4.5x3 also to test. I also balanced my props
@@divingfalconfpv4602 I like them better than the 10x5 from Gemfan or HQ for the simple reason that the oscillations were so bad using the higher pitched props that it was basically unflyable. It has certainly been a real pain in the ass to tune. I think just by sheer dumb luck and trial and error that I have it flying pretty good now. Considering that it is a 10 inch, and freaking huge, it won't be going with me on most outings, but there is certainly something exhilarating about flying something that big. I've also never seen a quad that just isn't bothered at all by prop wash but this one doesn't even flinch in normal prop wash scenarios. It's just solid in the air.
@William_NS it was weird. I had tune pretty good. Then something went wrong. And got extreme bad oscillation like too high D. I never changed props so maybe they got out of balance. These gf 10x5x3 when I got them were extremely out of balance i sanded for hours. Way way way more than the hq 10x4.5x3 which were pretty much almost perfect. I got inav in now. I was suppose to wait till after all the battery and prop testing but it instantly fixed oscillation and hot motors.. also heavy battery pretty almost fixed it.
Nice work. Can't wait to get comfortable using the new template. BTW, the new BBE is PWA now, so I guess we dont need to update anymore! Betaflight configurator is next 🤞
Videos like this make me so glad I fly Ultra. Lol
Yeah, but the flight performance is not as good as BF. :-(
Excellent, Mark! Thanks a bunch! 😃
Stay safe there with your family! 🖖😊
Thank you Mark!!
Having the motor rpm measurements is amazing! Those are pretty constand for a given prop and after adjusting for battery sag. Meaning you can actualy do some identification and automated optimal tuning based on them. Won't do much for ppl who already tuned their quad, but might allow for better "default" tunes if they are based on this knowledge.
Great video , I'm always rewatching this channel, because of the useful information. 👍
Thanks for the info Mark will definitely check those things out.
interesting for t-shooting
Bad ass - thanks, Mark
Great information!
great info thank you
Greatness! Do you plan on creating a controller script much like Brian White (PIDToolbox) patreons can get that would give you consistent tuning flights as well?
I don't see the desync "card" you mentioned. I emailed you a couple weeks ago about that issue on multiple quads.
Is there a way to set RDP (readout protection) option when flashing firmware?
What about one motor turning off in flight
Ok maybe ill go back to betaflight and try this. Do from scratch. No clue what happened my 10" started oscillating crazy lot. Hot motors at low throttle going down. Or pulling out dive. But pid were perfect before. Props look fine.
INAV short angle mode test seemed perfect though
Sounds like a loose screw, if it wasnt before
@chrisbee5481 first thing I thought. But wasn't. Checked even stack screws. Found antenna getting loose but didn't fix it. I only thing left is I swap props.
What frame is your 10" ? I like the new tmotor c10.5 props. Damn stiff and good quality.
Dont know if your frame and motors will match. I use 3215
@@chrisbee5481 aura 10.. 3115 900kv
4.5 help the ICM42688 any?
I recently built a 10 inch bird. I used 3115 900 kv T-motors with HQ 10x4.5x3 props. Are these motors sufficient in your opinion or should I try to find bigger motors?
I have same build same motors. Motors plenty big enough. Though I touch something on betaflight and started having huge oscillation at low throttle or pulling out dive. Couldn't figure out what even going back to old pids. Then old diff then old dump. I ended up just putting inav in and seem like it didn't do it. Idk. Can't figure out what I could of touched in betaflight.
How u like the 10x4.5x3? Suppose to be more efficient even though they r heavier. I have gemfan 10x5x3 on right now but I have 10x4.5x3 also to test. I also balanced my props
@@divingfalconfpv4602 I like them better than the 10x5 from Gemfan or HQ for the simple reason that the oscillations were so bad using the higher pitched props that it was basically unflyable. It has certainly been a real pain in the ass to tune. I think just by sheer dumb luck and trial and error that I have it flying pretty good now. Considering that it is a 10 inch, and freaking huge, it won't be going with me on most outings, but there is certainly something exhilarating about flying something that big. I've also never seen a quad that just isn't bothered at all by prop wash but this one doesn't even flinch in normal prop wash scenarios. It's just solid in the air.
@William_NS it was weird. I had tune pretty good. Then something went wrong. And got extreme bad oscillation like too high D. I never changed props so maybe they got out of balance. These gf 10x5x3 when I got them were extremely out of balance i sanded for hours. Way way way more than the hq 10x4.5x3 which were pretty much almost perfect.
I got inav in now. I was suppose to wait till after all the battery and prop testing but it instantly fixed oscillation and hot motors.. also heavy battery pretty almost fixed it.
@@William_NS mine was like that till something went wrong. Zero zero prop wash even before better tune