I used pre-cut 15% Lexen tint on my car windows and it came out great! No fingers or bubbles. This was 3 years ago, the tint still looks great and has not bubbled or changed colors.
for what car and how much was it? it shows 29.99 for pre cuts, i dont know if this is just the service to cut the tint, or the actual tint cut for my car.
You have to apply a ridiculous amount of solution imo. I tried to install precut today. It truly takes a ton of solution. My driver door ended up with a couple creases and those well known little bubbles that f'd it up
Hi cool vid looking for advise.i am havin air bubbles appear even though I am pressing quite hard to the film its only on the sides of a window middle top and bottom are fine just the sides
Does yours have a sticky side? Mine has a sticky side and I wonder if I still need to use soap water, or if that is going to kill the adhesive. It seems almost impossible to dry fit it
Hello lexen I am having trouble installing this where can I get all the stuff you used to install this and do I have to place the tint on the outside of the window first?? I really need an explanation
You place the tint on the outside of the window with the release liner towards you to shrink the fingers out of the window tint to the curvature of the window you are working on. Then, peel the release liner back has he did then apply the tint with the adhesive side out to the inside of the window.
Did he stick the film ON TO the soapy water? Is that what you do? I'll be doing this myself soon and I really can't find a clear instructional ANYWHERE !!!!
roadrunnerblink I'll be doing it too, watched a few vids of tinting. You clean window first, get it dry then spray again, get it good and wet. Apply film. But I always thought you apply tint from outside.
sorry for year late comment but it seems you didn’t get any good feedback. Yes you are supposed to apply onto soapy water. The soapy water acts as a lubricant so you can slide the film to position it. Once you have it in position, using a squeegee will push all that air AND soapy water out from under the film leaving you with a vacuum, causing the film to be sucked onto the glass essentially.
If you’re still interesting in trying it, try plastic bags with masking tape to protect your controls for peace of mind. That is what I will be doing when I give this a shot.
Not really trying to buy stuff from your website so maybe in the detailed Box you could leave a description of the solution you're using to clean the windows in what not would be appreciated
Before I buy this I just want to know like the dimentions that they come in like for example 20 "(inch) by 20 ft. Would that cover a whole window. No clue. Can anyone help me out
They are not pre shruk. You don't really need to heat shrink the side windows becuz they are flat. But u need to heat shrink back windshield becuz they r curved otherwise it will not fit properly.
@@DavidHernandez-ue4fz something like 3% and it depends on the weather. like if you live in high humidity or heat, so adjust more or less soap for evaporation because too little and you can't move the film and it tacks to the glass before you have time to adjust. Too much soap and it affects the long term success of the adhesive of the film
Why so much water? A light spritz from a spray bottle is plenty. You might as well be trying to apply it with a running garden hose. All this video taught me was to make sure if I go to a shop that they don't do it this way.
What ever gets the job done right, that’s all I care about. Water dries, but I can understand why you are fast to say someone with skill is not up to your par. Makes you feel better about yourself. I’m sorry you feel this way.
My passenger window wont roll down changed the motor switched fuses changed the up and down switch and made sure it's on track nothing will that be an issue putting tints on ?
If you did all I would assume that their is an issue in the wiring to the motor/switch. I would have both tested to see if they're receiving power. As far as tinting I've never done it myself but I see no reason as to why you couldn't install it without rolling the window down but obviously you won't be able to cover the glass that is tucked into the weather stripping.
@@jmmyjimmy106 thanks .. i did it now as for the rear 😂😂 looks horrible I was already expecting the worse from the rear I called the professionals for just the rear one guy quoted me $100 another $65 worse case I'll have to go with $65
@@uptownsfinest1598 Like the rear windshield or 2nd row door windows? Getting the rear windshield is always going to be fairly difficult if you have those window defrosters, that one of the main reasons I've never done it myself lol.
@@uptownsfinest1598 Yeah there's not much you can really do other than gaining experience on that I would imagine. I mean if it's only a couple of air bubbles you can take a razor blade and poke a hole and try to see if you can get them out but I'm not sure I'd recommend it.
Do you need heat gun to shrink tint and wich set of squiggees did use for all doors what type a solution did you use,is it baby shampoo please let me know thanks
El espacio arriba de el vidrio es muy grande...y la cantidad de agua es exagerada no explica que se necesita la pistola de calor para amoldar la película a lo convexo de los cristales...le falta para ser un trabajo profesional
Excellent job mate. All show no bs talk, just how I like it. To the point
No intro and no bs music. Proper video!
The instructions that come with the kit leave a lot to be desired that's for sure.
I used pre-cut 15% Lexen tint on my car windows and it came out great! No fingers or bubbles. This was 3 years ago, the tint still looks great and has not bubbled or changed colors.
Charles Bev
for what car and how much was it?
it shows 29.99 for pre cuts, i dont know if this is just the service to cut the tint, or the actual tint cut for my car.
Charles Bevan нич.иорчидщчшждт
@@TravisBiggie actual cut and ready out the box
Charles Bevan un yh8
Wow you make this look easy but I know it takes a lot of skill!
THE MOST SIMPLIEST WAY TO DO IT AND QUICK👍🏿👌🏿✌🏿
Luv this lexen product:)
I notice on your website it says the film needs to be best shrunk, at what point in this process is that done?
We use Johnson baby shampoo therefore it is safe on car interior. We now use micro fiber towels!
For the spray, you use Johnson baby shampoo, does it need to be diluted?
When you spray too much water on the film you’re not afraid to damage any electrical on the window?
Pu G
Skills! Great video. No talking. Just doing. Thanks!
very fast-very professional
Thanks great work
You have to apply a ridiculous amount of solution imo. I tried to install precut today. It truly takes a ton of solution. My driver door ended up with a couple creases and those well known little bubbles that f'd it up
Awesome👍 I’ll going do it for new Chevy 🤩
Straight to the point
Good job. !!
Can I use windex spay before apply film bro? Thanks
Excellent Tutorial
olá!qual produto você usa na instalacao?shampoo ou film on?
what tint did you install? its not in the description.
Hi cool vid looking for advise.i am havin air bubbles appear even though I am pressing quite hard to the film its only on the sides of a window middle top and bottom are fine just the sides
gav clark do you have felt on the sides. Tape them up if you do
or you didn't razor clean the inside of the glass and clean the gasket area where it bubbles up
Clean work 👍
Does yours have a sticky side? Mine has a sticky side and I wonder if I still need to use soap water, or if that is going to kill the adhesive. It seems almost impossible to dry fit it
You have to use a soap solution
Nice film work
Which tint shade is this ,35% or 20%
Excelente trabajo 👏👏👏🇦🇷
app plastic lagane ke lie shampo istemal karte hain ya sarf
What is the White card your using to to pull the weather seal back with? I have looked everywhere trying to find one and i cant. Thank you
Gemini Window Tinting dude use a credit card or something or a room key
Walmart has Bondo cards for $1.47 in a 3 pack.
How long should I take before I can open a window?
Did he heat shrink this or not?
the spray is blot my car seats how i remove the blot
OMG!!!! Love the fact that u have BTS-Mic Drop playing in the background 💜💜💜💜
That is not mic drop maam. Thought you were a bangtan follower. I guess you're not
you're the man.. Next...
Hello lexen I am having trouble installing this where can I get all the stuff you used to install this and do I have to place the tint on the outside of the window first?? I really need an explanation
You place the tint on the outside of the window with the release liner towards you to shrink the fingers out of the window tint to the curvature of the window you are working on. Then, peel the release liner back has he did then apply the tint with the adhesive side out to the inside of the window.
nice job i was wondering what kind of paper towels u used and were can i get the tool u used to get the film tuck under the gasket..
Blue shop towels work well
great job, wish he lived near me to install mine..... im scared 🤠
Did he stick the film ON TO the soapy water? Is that what you do? I'll be doing this myself soon and I really can't find a clear instructional ANYWHERE !!!!
roadrunnerblink I'll be doing it too, watched a few vids of tinting. You clean window first, get it dry then spray again, get it good and wet. Apply film. But I always thought you apply tint from outside.
You need a heat gun too. Sometimes more shrinking is required
Applied from the outside so that it can get scratched by debris and blow away? lol
roadrunnerblink
sorry for year late comment but it seems you didn’t get any good feedback. Yes you are supposed to apply onto soapy water. The soapy water acts as a lubricant so you can slide the film to position it. Once you have it in position, using a squeegee will push all that air AND soapy water out from under the film leaving you with a vacuum, causing the film to be sucked onto the glass essentially.
No shrinking?
Tint percentage how much
i. need. this work. please. help. mee
No shrinking??
The.best.
Love the fact you have to '' wash '' all of the door card, electrical switches /buttons, water inside the door etc to install it....
If you’re still interesting in trying it, try plastic bags with masking tape to protect your controls for peace of mind. That is what I will be doing when I give this a shot.
Good job
Nyimak cuci kaca ya kak👍
what percentage was this film? and what was the UV rejection? thanks
This is Medium Shade 35%.Please visit www.LexenAuto.com to purchase LX Window Film and Precut Tint Kit.
Not really trying to buy stuff from your website so maybe in the detailed Box you could leave a description of the solution you're using to clean the windows in what not would be appreciated
Yeahhhhhh BTS!!!! Fireeeeeeee
Laura Brown IKR I WAS LIKE OMGGGGGG BTS BTS BTS!!!!💜💜💜
Before I buy this I just want to know like the dimentions that they come in like for example 20 "(inch) by 20 ft. Would that cover a whole window. No clue. Can anyone help me out
You forgot to squeege the bottom, but overall did a good job
Now u got 5 stars on you
Nice
Super
How i can remove glue from this Windows tint if i remove it and the glue mark the window
No it is not preshrunk. You can use heat gun to shrink a little or no need at all.
Yooo I thought I was going crazy when I heard BTS in the background! Good video though👍
Leslie Castro نوط
Nice 👍
Most👌
how many % you're applying
Perfect 😆
Top 👍
👏
Omg is that BTS in the back ground❤️❤️
my tran theres always an army lmfao
Hlo
Me Tran hi
Me Tran: your way to cute
Me Tran fgjy
G
You make it look easy, its not that easy
Can you open the window without the tint coming off?
you have to wait 2-4 days so the tint adhesive dries down and then you can roll your windows.
I used dishes soap it’s was so bad when I spray it it dries what type
soap you used
can use shampoo also
what's the grey tool you use for the bottom trim??
Yu Le looks like some kind of wedge
Are these preshrunk? Cuz you don't show if u used a heat gun in in the beginning..
They are not pre shruk. You don't really need to heat shrink the side windows becuz they are flat. But u need to heat shrink back windshield becuz they r curved otherwise it will not fit properly.
Красавчик
I have bubble how i remove it?
Bhai aaki dukan Kahan hai
Is lexen tint a brand you recommend?
Yep
BTS~ :P thanks for vid, very helpful
What kind of solution do you use?
Johnson baby shampoo for mounting solution and Dish soap for cleaning.Thank you.www.LexenAuto.com
@@TintXfilm1 how much jonshon shampoo on water.?
@@DavidHernandez-ue4fz something like 3% and it depends on the weather. like if you live in high humidity or heat, so adjust more or less soap for evaporation because too little and you can't move the film and it tacks to the glass before you have time to adjust. Too much soap and it affects the long term success of the adhesive of the film
Like a boss...
Lo que me gusta de tu video es que explicas muy bien , que hay en las botellas,
Manuel Jimenez puedes usar agua con javon o limpia vidrios
nice job
Wow
Why so much water? A light spritz from a spray bottle is plenty. You might as well be trying to apply it with a running garden hose. All this video taught me was to make sure if I go to a shop that they don't do it this way.
It doesn't matter, everyone does it differently, what matters is quality and duration
Iceman350yt
What ever gets the job done right, that’s all I care about. Water dries, but I can understand why you are fast to say someone with skill is not up to your par. Makes you feel better about yourself. I’m sorry you feel this way.
Yes ur right
Looks good to me
is that liquid the glue too
My passenger window wont roll down changed the motor switched fuses changed the up and down switch and made sure it's on track nothing will that be an issue putting tints on ?
If you did all I would assume that their is an issue in the wiring to the motor/switch. I would have both tested to see if they're receiving power.
As far as tinting I've never done it myself but I see no reason as to why you couldn't install it without rolling the window down but obviously you won't be able to cover the glass that is tucked into the weather stripping.
@@jmmyjimmy106 thanks .. i did it now as for the rear 😂😂 looks horrible I was already expecting the worse from the rear I called the professionals for just the rear one guy quoted me $100 another $65 worse case I'll have to go with $65
@@uptownsfinest1598 Like the rear windshield or 2nd row door windows? Getting the rear windshield is always going to be fairly difficult if you have those window defrosters, that one of the main reasons I've never done it myself lol.
@@jmmyjimmy106 it sucks I tried twice with the pre cut tints failed lol
@@uptownsfinest1598 Yeah there's not much you can really do other than gaining experience on that I would imagine. I mean if it's only a couple of air bubbles you can take a razor blade and poke a hole and try to see if you can get them out but I'm not sure I'd recommend it.
Do you need heat gun to shrink tint and wich set of squiggees did use for all doors what type a solution did you use,is it baby shampoo please let me know thanks
you dont have to heat shrink for the side windows.
you can also purchase a complete window tint tools kit from amazon or ebay.there you can purchase it under $20 for complete professional tint tools
Baby shampoo name brand for install or dawn???
you can use any brand baby shampoo or dish soap.
Yunsoon Lee ok thanks Lee
Which dish Palmolive soap how many water.
Incase you spray some in your eye...No more tears
Some installers prefer the slip of baby shampoo over dawn.
I need that spray bottle!
Similar: www.amazon.com/Chapin-1002-48-Ounce-Sprayer-Multi-purpose/dp/B00002N8OB
www.amazon.com/Chapin-1002-48-Ounce-Sprayer-Multi-purpose/dp/B00002N8OB
Is the spray water or something else?
I use water and a little johnsons baby shampoo it works great
👍
I did not know that they are still making Silent Films. Thought they stopped it in 1921 when tone was added to it. 🤣
that upper line though
@Brumoth noticed it too ,was Curious!!!
Baby shampoo for install ??? Dawn for cleaning ???
baby shamp to install. non ammonia glass cleaner.
Glass palish masin
El espacio arriba de el vidrio es muy grande...y la cantidad de agua es exagerada no explica que se necesita la pistola de calor para amoldar la película a lo convexo de los cristales...le falta para ser un trabajo profesional
Wow korean pop song!! 불타오르네~~!!
What percent tint was used in this video?
I think it was 35% medium tint shade. thank you.www.LexenAuto.com
Are the kits preshrunk ?
They should BUT if they are not, have a heat gun ready.
Hi
How many % black...?
what tint % is this?
They answered another question a couple years ago... Medium Shade 35%
Thật tuyệt
Artist
Did you use a heat gun to finish the tint film?
no I did not use heat gun to finish it up on side door windows, but it helps if you can use heat gun.
lexenauto ok thanks
so when you buy precut tint, you dont have to use a heat gun at all? or shrink it?
Yes you need to use a heat gun if you have curved side door windows, and you must use heat gun on the back windshield.
C'est bien
hey, those pink hard card is scratch free on films?? where can i buy this from? thank you :)
We only include the small yellow squeegee in our precut tint kit. Thank you.
lexenauto if we buy the pre cut tint do we have to do any shrinking with a heat gun on the rear Glass
Yes you need to heat shrink the rear windshield precut tint for most cars window.
yes you need to heat shrink the film on back windshield.
LEXEN.LLC
443-315-5047
www.Lexenauto.com
need to heatshrink all of the windows? or sides come done already?