2 transformers INVERTER 12V to 220V
Vložit
- čas přidán 7. 09. 2024
- In the next project, I will make a powerful inverter using 2 pulse transformers, which convert 12V battery to 310VDC with a capacity of 1000VA. This is step 1 in my project. step 2 i will convert 310V into 220VAC using H. bridge i will use 4 mosfet IRF460. Can optionally frequency 50HZ or 60HZ. choose sine waves or square waves.
If you like my videos, please like, share it and don't forget to subscribe to my channel, thank you very much.
Facebook group : bit.ly/Creative...
Download file here : File 22 in bit.ly/AllLink
#Inverter
#12Vto220V
#sinewave
Hello, I made this inverter and it works, the bad thing is that the mosfets get too hot and even with a good heat sink they always get customers that can be done to solve this problem
This gay is Chinese he cant answer your question because he cant reply in English to fix your issues the mosfet get hot because the frequency need to match the wattage need if you using 32 35 60 or 100khz to get 100 watt that will work just fine but if you need more wattage use a trimpot to adjust the frequency to the wattage till the mosfet stop getting hot or use EE 42 or EE55/5/5 ferrite core transformer to get the power you need but just remember the frequency is the key to getting max wattage at the right temperature if the frequency is too low the wattage will cause more heat to be higher because the load is dropping the magnetic flux and frequency at the same time causing the mosfets to loss conductivity in the transformer and then starting to short circuit in each duty cycle so for use 250 kHz to 500khz for 1 to 2 kw of power
Bro you are the king of inverters !!
Excellent service but frequency! khz. 20h 30h. Thanks for video
Bro I maked this transformer but it's consuming 1amp without load where is the problem I reminded the transformer with 4-0-4 turns should I change the winding please help me
Try to use wire with larger diameter, larger cross-sectional area wire means less resistance !
In a earlier video u have made a 60amp smps.. please complete this with feedback controll....
,😀😀😀😀😀 waiting for second part..... Great job sir
I am designing it. wait me
I don’t understand about your winding direction, at the 3+3turns winding you wound it in clockwise direction but at 45turns winding you wound it in anti-clockwise. Why is it so?
You are unique, you can make wonderful projects. CONGRATULATIONS CONGRATULATIONS. I am waiting to see the project of the step-down from 50v to 30A. A warm greeting .😊☺️
Powerfull voltage inverter.
Tanks.
Good but no circuit diagram, just watch and enjoy. No one make this inverter without clear explaination
drive.google.com/file/d/1sGRaVUshHrhkqATQQ9gfB8RN-xvYww7m/view
file in video description
Hi brother, Why did you add another Mosfet to power the circuit. The ground wire is going to trough a MOSFET. Is it simple low voltage protection?
V.good Waiting for step 2
I am designing it . wait me
wooow 50 or 60 hz and we have the possibility to chose between square or sine . great respect dear friend you are the king of inverters . i cant wait to see the next video. please share it as soon as possible and thank you.
and about converting 310vdc to sine using h-bridge. please can you do it this time with atmega8 with full protection ??
Sir we made the above circuit as per your design and got 300v dc but when we try to load filament bulb for some time MOSFET get damaged .. can please help me
Bro please tell me what what is the no load consumption of this inverter
No load ~ 0.05A
Thank you bro love your channel.
rất thích các video hướng dẫn của bạn.
thanks!
Very Clever Design!
Thanks bro
Great job sir
thanks
Hi, excellent channel, I'm from Mexico and I'm just learning, but I'm interested to know which inverter I could feed from 110 volts to 220 for an air conditioner to work.
Thank you
EGS002 inverter
I am big fan sir plzzz make ups 1kw and inverrter
yes, wait me
I m a big fan of u...
I also want to make sg3525 board that one used in this video... please make a video for this..
Good project man!😀 you are great! you could make an inverter or a smps source with pulse transformer and tl494? I have many of these IC and sg3525 is hard to find on my area.
Yes, wait for me, I'll do it
he he he lên ti-vi là em kêu vợ chùi cái bếp cho sạch và mới chứ em.
Great work, please make high current mppt charge controller. Thanks
That project is very difficult, I will try.
We are waiting for mppt project.
Tks, friend!
Renato França - São Paulo - Brasil
excellent bro...
thanks bro
My ups low load cutoff ..how to avoid minimum load cutoff
hoal mu good the projects of the channel ... as it would be with battery charger ... open a project that has the battery charger ingraded to recommend, thanks greetings from argenina
That's a good idea, wait for me
Gôd....Thank admin!!!
very nice
Except from awesome inverter projects i think he did an electrical electronics engineering course
sir, is it possible to use a 0.75 mm wire in the secondary section, because I did not find a litz wire
yes, ok
Thanks
In pwm board the capacitor C5 is no value
is 1uf 25v
I have e question... When I rewound my transformer.... about 80 turns...I am getting very high voltage....above 1000v and it destroyed my output rectification diodes and my led bulb....why is that so..
Add voltage feedback. It will limit the voltage
Awesome Brother....Really Nice! Video.
thanks
File 22 not available in link 😢
Please Sir could you make a cheap puresine wave ferrite core inverter without t the use of a micro controller and yet effective?
maybe, but very low performance. about 50%. eg 100W 12V battery power. You will get 50W from 220V.
How to make a auto cut changer for inverter when electricity is cut then inverter is on... Please make a video...Thankyou...#Inventionswithtaufik
From pakistan
I want to make a 500watt inverter with old ups 12-0-12 Transformer please tell me how I can make the inverter.....
Thankyou
There are many diagrams in my channel. You can find it in the list inverter.
Ok Thankyou So much you are great 💓❤️😇
Homemade102... please make a ferrite core 1000va stabilizer... i want to give mains 90v to 300v range as input and output should be 220VDC REGULATED with feedback controll.....A humble request....
It is quite simple, I will do it
@@PhdHung.... If the output will be 230v AC sine wave instead of 220v dc... it will be much better... thanks
Sir, what is the purpose of Q1 the fifth mosfet on circuit board attached to the negative terminal of the battery.
It protects reverse battery. If you connect + battery with - circuit, - battery with + circuit. circuit not working, not burning.
@@PhdHung Thank you sir for your reply just one more question as this inverter is rated at 1000VA therefore (1000/12=83) approximately 83Amp will pass through this mosfet when inverter is operating at its max power, is this single mosfet is sufficient to handle this much of power.
Atx transformer. Sir Parallel connection to 220+220 AC volt will work please reply
serial, not parallel
series connection of transformer secondary output
You need to show the circuit.
Why is the DC voltage dropping
humm, increase your copper wire diameter.
Why don't you show your circuit diagram..?
Project file in video description. Download and open with Winrar on PC.
Nice vedio broiiiiii
thanks bro
It can really produce 1000 watt?
1000W is the peak power. Continuous capacity 1000VA
Pleace file downoload in not Facebook
Great keep it up bro
thanks bro
Awesome
Hi , which IC best for steady 220v TL494 or sg3525
it's similar, but I think sg3525
Hi, am Jerry can you make a steady 220v inverter using IC CD4047 .(feedback).
can not
Bro what is the maximum output of this circuit in watts without overheating MOSFETs
max peak 1000W
And what is the continuous power without overheating MOSFET
Chota board ka canection nhi dikha aur battery ka bhi canection nhi dikha to kaise mane ki acha bana ha inverter
Can you make inverter 2 transformer in parallel?
I don`t undestand , when you use the plate i don`t undestand nothing , please show me the plain . one cuestion : the volt is 300 volts because the light is not dead ? the light is 220 v and your voltaje is 300 volt , and not to fuse?? . In the video you not say the propeties of condensador please you say this. The control voltaje you buy? or you made? please incluyed this plane also . aaaa forget how amperies have this inverter , maximum . sorry for may english , I admiration to you , greeting for Spain , you firend Luis , bye.
I use it for H-bridge 310V to 220V.
i write diferent cuestion , please answer all
How the frequncy out put?
It"s not completly
It is DC voltage. In the next video, I will build the H. bridge that will convert the DC voltage into AC.
anh ơi cho em hỏi cái chân thứ 2 từ trái sang phải của boar dao động dùng để làm gì và đấu dây như thế nào ạ?
A ơi. Khi hồi tiếp về đúng điện áp chuẩn rồi. Biến áp kêu rè rè. Nâng cao max lại ko kêu là sao vậy a
Hello my friend, excuse me, where is the pin number 2 of the pwm model installed on the circuit?
Diagram in video description
@@PhdHung Not connected to the circuit, right?
@@PhdHung I want to change the voltage, but I can't! where is the problem from ?
What do I need to change on transformer winding if I want input to be 24V
You need to use primary 6 + 6 turns
@@PhdHung Thanks a Mill
pwm not complete again ,please tell us the value of capacitor and resistor to which no values are written
All information is in the file in the video description.
No it's not, look the pwm schematic and jpg, 2 of components missing values.
Awesome project :)
thanks
@@PhdHung سر کہیں فون نمبر ہی لکھ دو
I want to design 1000va ,70v ac in out put.my in put should be 220v ac in 20khz
oh, that's a good idea, I'll do it, wait for me
Hello. I'm like your inverters and how you are can charge 12V battery and you are can made Solar Panel project?
I am designing it . wait me
Where do you get these transformers from that you are rewinding?
I took it in the old PCB. eg old TV, ups, ATX power supply etc...
The diagram of the pwm board is not clear please explain those pins
Please watch the previous video
Please can use tl494 in place of the ic
yes, wait me.
thay irf512 = irf3205 dược không ad
3205 ok luôn
@@PhdHung thank ad nhiều nha
What is the working frequency
What is the idle current?
~ 0.01A
hi can i use regular coil wire instead of litz wire?
Hello my friend, can you help me? I can't adjust the voltage! Where do you think the problem comes from?
can it ported onto egs002 bridge? to convert output to AC?
Hola amigo muy buenos tus proyectos, estoy analizando como funciona el 1000 VA inverter uses 2 transformes y no puedo entender como funciona el IRF3205 donde va puesta el negativo de la batería, se que es para protección contra la inversión de polaridad de polaridad. ¿como se une Drain con el source para empezar a funcionar el inversor. Por favor una breve explicación.
Hola amigo el positivo es el cable amarillo que se ve en el vídeo y negativo es el color azul allí van conectados la batería saludos
Làm board sg3525 ở video nào thế a? E không tìm thấy
bo đó anh làm lâu rồi, anh gỡ ở board cũ ra. em tải file ở mô tả video nhé, có file mạch PWM nhỏ đó ở trong đấy.
Hallo sir, pleasd make skemati egs 002 and suplay 20 mosfet more. Thanks
For low freq
I am designing it
I am waiting for it sir. Thanks
E 42 thì quấn bao nhiêu vòng vậy anh, mạch này có hồi tiếp kg anh?
hola muy bueno , como seria con cargador de bateria .... si se le puede anadir un cargador
Кроме количества витков и способа разборки трансформатора, видео не несёт никакой информации. Значит оно бесполезно.
Es muy complicado realizar un inversor de onda pura??
Hi Sir Please help us for some components at sg3525 section Pin no: 2, 5, 8, 10 and 15 capacitors value ?? please
heloou frends! what is R8 Resistance? its mising.
how to overcome the voltage drops in the battery when hit by a heavy load

put more batteries in parralel
the pcb file its unavailable
5:28 - secondary winding direction - in other deriction ?
what do you mean?.
Direction winding primary & secondary - are they reversed?
Can this be use as a split phase inverter 110 / 110 volts
Thankyou very much, can i get the schematic diagramme
capacitor value missing in pwm card and please make schematic in pdf form i dont understand pcb very much
View component values in the img file
Please how do you combine the two transformers ,is it in series or parallel
In series each transformer out 110v
eagle schematics are not always clear to me
U must mention the guage of copper while teaching no need of dimensions
good morning!! excellent all your projects !!! I like them all!! I want to do your investor projects with ferrite transformers but they are 220V and in my country it is 110V and I would like you to tell me how many turns I have to take to get that voltage in addition if you could do a voltage inverter project but recharge the battery ... greetings from Venezuela !!!
Reduce 1/2 turn secondary transformer
irfp260n mosfet inverter board diagram
Puedes decirme como hace un inversor 24v a 220v
increase x2 number of primary wires
Where can find this transformers?
Sir Can we use 2 big transformer in low frequency sine wave inverter??
No inverter. This is transformer CC-to-CC.
INVERTER IS CC-to-CA, ori CA-to-CC.
Digram of this inverter please give sir
in the video description
Bro, please share the inverter