Clear fix and helpful walkthrough. Even though you're in the plumbing field, you're helping many save money. You're a credit to your profession; hats off to you, my friend!
Thank you for this video. You just saved me almost $200 for a simple little fix! I just ordered the caulk and will be picking it up shortly. Then I'll be following your video! Thanks again.
I have been putting this off for a while now. I went to big box store to get some caulk and chose DAP adhesive sealant. It says it’s for kitchen , bath and plumbing . Thank you for this great tutorial.
Peter! Glory to God in the highest bro.. Awesome video and explanation of it.. Super easy fix. Thanks so much for your help and time.. Peace, health and prosperity be with you bro! Jesus Christ! I subbed!
Depends on how much more space you're talking about. If it's a slightly larger gap, you may be able to still get away with caulking it. Just know that the larger the gap, the more challenging it's going to be for the caulk to hold long term. If it's a sizeable gap, you may want to consider having the spout re-installed.
thankyou! appreciate the video! 2 questions, do you "wet" the caulk bead with a water spray before smoothing with finger? also do you painters tape around the faucet and remove after smoothing to get a crisp caulk line? Caulking has never been a problem for me, getting a nice smooth consistent finish is...:)
Hi Al! My process varies slightly depending on what sealant I am using on a given application. If I am using caulk, I typically will wet my finger before smoothing it out. I’ll often go over it a couple of times with a mix of wet and dry fingers, using paper towels to clear the excess until I am satisfied with the final product. In some scenarios, I’ll use silicone. In this case, I use the same procedure of spreading it nicely with my finger and wiping the excess, but I do not apply any moisture. I don’t use painters tape around the faucet as it’s pretty easy to clean the excess with a paper towel, but I don’t see why it would be a bad thing to use it if you are concerned about cleaning it quickly enough before it begins to dry.
A plumber reinstalled my bathtub spout the other day after shortening the copper pipe, but the caulking that was used around the outside of the spout ended up looking terrible and I am thinking about removing the caulk and putting new caulk so that I can ensure a proper seal. Some areas of the spout have a very narrow gap between the spout and tub wall. Even with the narrow areas, will it still be possible to use a razor knife to remove the caulk without having to take off the entire spout? I do not feel comfortable removing the spout and reinstalling it. Thank you in advance
Oh my. I'm sorry to hear about this! Yes, you should still be able to use a razor knife to cut it away. Remember when re-caulking to leave a small section at the bottom of the tub spout (about 5-7 o'clock if viewed as a clock) free of any sealant. That way water has a chance to escape into the tub should the spout itself ever leak internally.
@@two7plumbing Thank you for the quick response. Based on your experience, once you start peeling a bit of the caulk, does the rest peel away with it or does only bits and pieces peel and a lot of cutting and scraping involved? Just trying to see if the removal process will be a big project. I am nervous. I am also OCD so I am nervous about applying the silicone too and wanting it to look super smooth and clean lol
@vicktv33 well it primarily depends on whether silicone or caulking was used. In my experience silicone tends to shred apart as you remove it while caulking tends to peel off much easier.
In theory you may be able to get plumbers putty to work as a temporary measure if the gap isn't too wide. I wouldn't keep it like that for long though.
Sorry to disappoint. My “camera” was my 12.9” iPad on a massive tripod stand, so it was all I could do to catch as much as I could in this video 😂🤣 There really isn’t much special technique involved though. I like using a razor knife to scrape away the existing caulking, but you can also use actual caulk removal tools or even a chisel if you don’t have access to anything else. Most items with a point or ability to scrape are fine. Just gotta use some elbow grease. To apply, just squirt the caulk or silicone out in a little line around the spout (leaving the bottom open) and then use a finger to wipe the excess off into a paper towel. If you’re using caulk, it’s sometimes easier to wet the finger a bit first. I hope your project goes well! Don’t hesitate to ask if you have more questions!
Thank you for the tutorial-novice learner over here. What if water sits in the tub spout? Can that go back behind the wall and create a problem? Thanks in advance.
My pleasure! Any water that sits within the actual spout, should eventually drain directly into the tub (this may take some time if it’s an older spout that is clogged). Provided the spout is installed correctly and not damaged, it should not go behind the wall.
Plumber installed new shower fixtures. He made several mistakes and a nothing I can do now without removing the new tile wall. I recently filled my baby bathtub and noticed plumber putty is coming out in the water that comes out of the bathtub faucet. Should I be worried? Will this stop?
Unfortunately, I am unable to diagnose this request without a proper evaluation. I would recommend you reach out to a reputable company in your area for a second opinion if this is a concern. Make sure to verify licensing for your best bet at getting someone who truly knows what they are doing.
Great question! We don't seal the bottom because we want a means for the water to escape back into the tub should there ever be a leak within the spout.
Just put in a new diverter repair kit. When pulling up lever for shower there is water coming out of tub spout which didn’t happen before. I notice that the cup seal doesn’t seem to stay in. What can I do to repair this I have a moen single handle design. I used a universal diverter repair kit. Thank you
A lot of the universal repair kits will leave you with a system that doesn’t fully divert water like what you are describing. I recommend replacing the spout entirely with a reputable brand like a Moen.
@@katherinekochis7896 in that case, the simplest solution would be to replace it with another Moen slip spout. Slip spouts don’t require a specific measurement and, if you’re replacing an existing Moen with another Moen, it’s unlikely you’ll need to cut the copper piping at all.
If there is a gap between your tub spout and the shower wall, it is a location where water from inside the shower stall can run down and into the gap as well as the wall. This gap should be sealed for that reason to protect against water damage. It isn’t necessarily about the spout itself leaking.
Sir you missing and not talking about the obvious problem...... YOU NEED TO SEAL THE PIPE BEHIND THE SPOUT WITH CAULK OR PLUMBERS PUTTY TO PREVENT WATER FROM GETTING INTO THE WALL. RIGHT? RIGHT? GOOD VIDEO ANYWAY.
I didn't miss that, but it was also beyond the scope of this video as it isn't the correct fix for the leak which this video covers. This video is also geared for the average homeowner who isn't going to be comfortable removing their tub spout. If the tub spout is removed, I agree that it is good practice to seal around the pipe as well. However, the only additional water this would prevent from getting into the wall is if the spout itself is leaking and spraying water back. In this case, greater work is needed anyway. Sealing around the spout as shown in this video is plenty sufficient to prevent water that is trickling down the shower wall from getting back into wall itself.
For this application, the brand isn’t really a big deal. More than likely anything you find at your local building supply house will be perfectly sufficient. If you want to go an extra step, you can look for one that specifies “kitchen and bath.”
This most commonly means that a the seal isn’t holding water against the pipe. This can be the result of a damaged seal, insufficient tightening, or simply a low quality product. Many cheap tub spouts will exhibit this problem, which is why I recommend the Moen used in this video.
@@two7plumbing I just had a new one installed today. I notice water drips down the back towards the wall (where the open spot is at the bottom), before even pulling the diverter up. After reading reviews, I think it's because I chose kohler. Hoping this is an easy fix of just switching product to Moen!
@@bethrocks sounds like the existing spout is either not installed properly or is defective. Switching it over will likely address the issue, though I’d pay attention to the condition of the pipe too when you remove it to check if there are any spots where it is damaged.
@@two7plumbing 3 years ago a plumber replaced the tub and shower piping and valve, then another worker worked on putting back tiles and he left those gap around the pipe, which I calked, but was not sure if there was a better way to seal. The apt below is now having a leak from me and I was wondering if that caulking is failing. Before I unscrew the faucet piece and I wanted to be ready as to what to do in case water was getting through
@@anthonydefex I’m afraid I can’t fully offer a diagnosis from the info alone, but I can tell you that if it’s properly sealed, it shouldn’t be leaking from water within the shower structure. Realistically, you’d even be okay to not deal around the actual pipe so long as the spout is installed correctly and the spout is properly sealed to the wall. However, it is still good practice to seal the hole.
Repairs for the handles and stems/cartridges above are not always consistent. You’ll need to verify the manufacture as well as the exact problem and go from there. Typically, however, it isn’t the same repair as shown here.
This will depend on the specific brand and style that you are using. Make sure you have a clean cut on your copper line. Most brands will slide right on, though you may need to first check to see if yours needs to be loosened to leave play for the oring.
@@two7plumbing I was actually referring to the o-ring literally inside the spout tube. It comes new in all slip on spouts that I have seen. I followed instructions and cleaned the copper tube and cleaned it up and used some silicone lube and when I slipped it on the o-ring that's in the plastic tube inside the spout came out and it's all angled in the plastic tube and I'm trying to get it back in place so this spout can be used. Specifically this is a Danco slip on spout with diverter and personal shower head feed.
Honestly, the problem is likely with the product itself. Danco is a low quality product that is immensely frustrating to work with. I actually refuse to install their spouts as they run a very high risk of immediate failure. Many of theirs also require you to tighten the spout to the piping in such a manner that you can damage the pipe itself if you aren’t very careful. I would recommend going with a better quality product such as the Moen used above.
water is coming out and up out the back of my tub spout. that's not normal, right? I just noticed it today. I was afraid water might be going back into the wall. If I re-sealed it is that all I need to do or do I need to replace the tub spout first? there's no seal at all. TIA!
@@vaneese85 if it’s leaking water from the back of your spout when the tub or shower is in use, this would indicate a failure within the spout itself. In this scenario, replacing the bead of caulk shown in this video will not be sufficient. You’ll need to remove the spout and address the issue accordingly (often by installing a new spout).
It depends on the application at hand. If the home has occupants who ate more likely to be rough on the spout (children playing in the tub), I'd use 100% clear silicone as it'll flex a bit easier than caulking and will hold up a bit better. If this isn't a concern and the spout is nicely positioned against the wall of the tub, any white caulking would be fine and tends to look much nicer if applied well
@@two7plumbing Thanks. We are trying to redo the face plate and spout. Have read different things about leaving the bottom side uncaulked. Would Kwik Sweal Kitche & Bath be okay? Thanks
@mogtrader8 yes, that product would be fine. I recommend leaving the bottom portion uncaulked (from about 5 to 7 oclock). Water won't be able to get into the wall from that position and it will help to allow water from a leaking connection within the spout to escape into the tub instead of ending up I'm the wall.
Great question! This depends on the application at hand. Most valve trims already have a gasket on the backside of the trim which deters water from entering into the wall. For this reason, I do not typically caulk around them. However, if the trim does not have this gasket and/or if it is installed on an uneven surface (such as a deep grout line) which may prevent the gasket from fully sealing, I will go ahead and caulk around them too.
@@two7plumbing wow thanks for replying!! Based on what you mentioned, I’m thinking this one KES Shower System 12 Inch Rain Shower Head with Handheld Spray Shower Faucets Sets Complete Pressure Balance Shower Valve and Trim Kit, XB6230S12-BK, doesn’t have one & need to be caulked?
@Kristine B I’m not familiar with this specific system. You can always contact the manufacture and ask them to confirm or you could just caulk it anyway. It won’t hurt to do so.
This is a possible location of a leak. Though in my personal experience, it’s definitely not the more common leak. Failed seals at the wall are notorious for allowing water that trickles along the shower wall to leak into the wall. I see this almost every week.
Though I will agree that if you’re using a cheap quality product, what you’ve stated is going to be a high likelihood. Many of the cheaper versions don’t seal properly to the pipe and will leak from inside the spout. This is why I’m highly selective about the products that I use as well as the products that I recommend in my videos.
Yep! Not everything is worth our time. Just as I don’t really want to block out a section of my schedule just to put a bead of caulk on a spout, many people would be appreciative to not have to pay the service fee for a bead of caulk. Win-win in my opinion! :)
@Supa Trending Daily I would love to find a good and honest handyman. Unfortunately, in my experience every one of them I’ve come across does work they aren’t licensed to legally perform and end up causing problems. I’m certain there are good ones out there who are ethical and knowledgeable so this isn’t a blanket statement against them, but sadly I’ve been unable to find them.
Not wise to use a utility knife on or around the fixture. DAMAGE ! To either fixture or tub wall. I would want to hire someone more meticulous in their work.
Nothing wrong with using a utility knife for this situation. In fact, they now make utility knives designed for this specific application (I own one, though this tool wasn't around at the time this video was shot). I do agree, though, that it wouldn't be wise for someone to use a utility knife for this if they are not competent in the tools they are using. May I ask what method you would use in this situation?
Clear fix and helpful walkthrough. Even though you're in the plumbing field, you're helping many save money. You're a credit to your profession; hats off to you, my friend!
Thank you so much! I truly appreciate your kind words!
You are true bro. Giving tips on how people can help themselves save money, even though it's your occupation. Great work man!
I appreciate that! Thank you!
Thank you for this video. You just saved me almost $200 for a simple little fix! I just ordered the caulk and will be picking it up shortly. Then I'll be following your video! Thanks again.
My pleasure!
I just did this last year and I’m back again doing it again. Great video!
Yeah, it's sometimes an annual thing depending on how the spout is installed and what kind of usage it gets. Glad you've found the video helpful!
@@two7plumbingthat's good to know. It seems once a year my faucet in my tub has a huge gap all of a sudden.
I have been putting this off for a while now. I went to big box store to get some caulk and chose DAP adhesive sealant. It says it’s for kitchen , bath and plumbing . Thank you for this great tutorial.
So glad you found it helpful!
Peter! Glory to God in the highest bro.. Awesome video and explanation of it.. Super easy fix. Thanks so much for your help and time.. Peace, health and prosperity be with you bro! Jesus Christ! I subbed!
Jared Showers my pleasure! I’m happy I was able to help!
What does your jesus have to do with plumbing? Nothing.
great video, my tub always manages to get water outside and onto the floor.
Glad you found it helpful!
They have plastic tools to remove caulk that won't damage your tub wall. Why use a razor ? You risk damage. Cripe ! That is your mistake.
Just came across this video, awesome info. What if the space is bigger than what is in ur video? Thanks for the vidro
Depends on how much more space you're talking about. If it's a slightly larger gap, you may be able to still get away with caulking it. Just know that the larger the gap, the more challenging it's going to be for the caulk to hold long term. If it's a sizeable gap, you may want to consider having the spout re-installed.
thankyou! appreciate the video! 2 questions, do you "wet" the caulk bead with a water spray before smoothing with finger? also do you painters tape around the faucet and remove after smoothing to get a crisp caulk line? Caulking has never been a problem for me, getting a nice smooth consistent finish is...:)
Hi Al! My process varies slightly depending on what sealant I am using on a given application.
If I am using caulk, I typically will wet my finger before smoothing it out. I’ll often go over it a couple of times with a mix of wet and dry fingers, using paper towels to clear the excess until I am satisfied with the final product.
In some scenarios, I’ll use silicone. In this case, I use the same procedure of spreading it nicely with my finger and wiping the excess, but I do not apply any moisture.
I don’t use painters tape around the faucet as it’s pretty easy to clean the excess with a paper towel, but I don’t see why it would be a bad thing to use it if you are concerned about cleaning it quickly enough before it begins to dry.
Sound advise Peter, thanks.
Great, helpful information! Thank you!
You’re very welcome!
Thanks for this.
I was cleaning the tub and wacked mine with my knee. The silicone seal popped.
Hope your knee is okay!
@@two7plumbing knee is fine, minus a minor bruise.
Thanks Peter for this video!!
Great tutorial
Thank you! More like it coming soon!
A plumber reinstalled my bathtub spout the other day after shortening the copper pipe, but the caulking that was used around the outside of the spout ended up looking terrible and I am thinking about removing the caulk and putting new caulk so that I can ensure a proper seal. Some areas of the spout have a very narrow gap between the spout and tub wall. Even with the narrow areas, will it still be possible to use a razor knife to remove the caulk without having to take off the entire spout? I do not feel comfortable removing the spout and reinstalling it. Thank you in advance
Oh my. I'm sorry to hear about this! Yes, you should still be able to use a razor knife to cut it away. Remember when re-caulking to leave a small section at the bottom of the tub spout (about 5-7 o'clock if viewed as a clock) free of any sealant. That way water has a chance to escape into the tub should the spout itself ever leak internally.
@@two7plumbing Thank you for the quick response. Based on your experience, once you start peeling a bit of the caulk, does the rest peel away with it or does only bits and pieces peel and a lot of cutting and scraping involved? Just trying to see if the removal process will be a big project. I am nervous. I am also OCD so I am nervous about applying the silicone too and wanting it to look super smooth and clean lol
@vicktv33 well it primarily depends on whether silicone or caulking was used. In my experience silicone tends to shred apart as you remove it while caulking tends to peel off much easier.
can you use plumber's putty for this? As a temporizing measure can you put tape around it until you can get the correct type of caulk?
In theory you may be able to get plumbers putty to work as a temporary measure if the gap isn't too wide. I wouldn't keep it like that for long though.
@@two7plumbing thank you
@@ebthonit's my pleasure!
Would have been nice if you had the camera closer so we could see your technique for removing and reapplying the new seal.
Sorry to disappoint. My “camera” was my 12.9” iPad on a massive tripod stand, so it was all I could do to catch as much as I could in this video 😂🤣
There really isn’t much special technique involved though. I like using a razor knife to scrape away the existing caulking, but you can also use actual caulk removal tools or even a chisel if you don’t have access to anything else. Most items with a point or ability to scrape are fine. Just gotta use some elbow grease.
To apply, just squirt the caulk or silicone out in a little line around the spout (leaving the bottom open) and then use a finger to wipe the excess off into a paper towel. If you’re using caulk, it’s sometimes easier to wet the finger a bit first.
I hope your project goes well! Don’t hesitate to ask if you have more questions!
Really helpful. Thank you so much.
My pleasure!
Hi Peter. Does plumbers putty work as a seal? I understand that it doesn't dry...
No, don’t use putty. It does dry out and will crack when this happens.
Thank you for the tutorial-novice learner over here. What if water sits in the tub spout? Can that go back behind the wall and create a problem? Thanks in advance.
My pleasure! Any water that sits within the actual spout, should eventually drain directly into the tub (this may take some time if it’s an older spout that is clogged). Provided the spout is installed correctly and not damaged, it should not go behind the wall.
Plumber installed new shower fixtures. He made several mistakes and a nothing I can do now without removing the new tile wall. I recently filled my baby bathtub and noticed plumber putty is coming out in the water that comes out of the bathtub faucet. Should I be worried? Will this stop?
Unfortunately, I am unable to diagnose this request without a proper evaluation. I would recommend you reach out to a reputable company in your area for a second opinion if this is a concern. Make sure to verify licensing for your best bet at getting someone who truly knows what they are doing.
why he doesnt caulk the whole thing around it? why he left that bottom not seal?
Great question! We don't seal the bottom because we want a means for the water to escape back into the tub should there ever be a leak within the spout.
Thank you 🙏🏾
Just put in a new diverter repair kit. When pulling up lever for shower there is water coming out of tub spout which didn’t happen before. I notice that the cup seal doesn’t seem to stay in. What can I do to repair this I have a moen single handle design. I used a universal diverter repair kit. Thank you
A lot of the universal repair kits will leave you with a system that doesn’t fully divert water like what you are describing. I recommend replacing the spout entirely with a reputable brand like a Moen.
@@two7plumbing It is a moen so
I how do I measure the tub spout so that I can by a new spout or does it matter.
@@katherinekochis7896 is your existing spout a slip style or a threaded style?
@@two7plumbing slip
@@katherinekochis7896 in that case, the simplest solution would be to replace it with another Moen slip spout. Slip spouts don’t require a specific measurement and, if you’re replacing an existing Moen with another Moen, it’s unlikely you’ll need to cut the copper piping at all.
How do you know if there's a leak or not? Mine has a gap for few years. Thanks
If there is a gap between your tub spout and the shower wall, it is a location where water from inside the shower stall can run down and into the gap as well as the wall. This gap should be sealed for that reason to protect against water damage. It isn’t necessarily about the spout itself leaking.
@@two7plumbing there is a yellow stuff look like a sponge behind the spout.. any idea what that is? I appreciate your help!!
Sir you missing and not talking about the obvious problem...... YOU NEED TO SEAL THE PIPE BEHIND THE SPOUT WITH CAULK OR PLUMBERS PUTTY TO PREVENT WATER FROM GETTING INTO THE WALL. RIGHT? RIGHT? GOOD VIDEO ANYWAY.
I didn't miss that, but it was also beyond the scope of this video as it isn't the correct fix for the leak which this video covers. This video is also geared for the average homeowner who isn't going to be comfortable removing their tub spout.
If the tub spout is removed, I agree that it is good practice to seal around the pipe as well. However, the only additional water this would prevent from getting into the wall is if the spout itself is leaking and spraying water back. In this case, greater work is needed anyway. Sealing around the spout as shown in this video is plenty sufficient to prevent water that is trickling down the shower wall from getting back into wall itself.
What brand caulk do you recommend? Also how long should I wait for it to dry?
For this application, the brand isn’t really a big deal. More than likely anything you find at your local building supply house will be perfectly sufficient. If you want to go an extra step, you can look for one that specifies “kitchen and bath.”
What might cause a newly put on spout to shoot water back towards the wall after pulling on the diverter?
This most commonly means that a the seal isn’t holding water against the pipe. This can be the result of a damaged seal, insufficient tightening, or simply a low quality product. Many cheap tub spouts will exhibit this problem, which is why I recommend the Moen used in this video.
@@two7plumbing I just had a new one installed today. I notice water drips down the back towards the wall (where the open spot is at the bottom), before even pulling the diverter up. After reading reviews, I think it's because I chose kohler. Hoping this is an easy fix of just switching product to Moen!
@@bethrocks sounds like the existing spout is either not installed properly or is defective. Switching it over will likely address the issue, though I’d pay attention to the condition of the pipe too when you remove it to check if there are any spots where it is damaged.
what about any gaps on the wall through which the water pipe goes through? How to best close that up?
Same thing. Use either caulk or silicone to close up the home where the pipe goes through the shower wall and then install the new spout.
@@two7plumbing ty
@@two7plumbing 3 years ago a plumber replaced the tub and shower piping and valve, then another worker worked on putting back tiles and he left those gap around the pipe, which I calked, but was not sure if there was a better way to seal. The apt below is now having a leak from me and I was wondering if that caulking is failing. Before I unscrew the faucet piece and I wanted to be ready as to what to do in case water was getting through
@@anthonydefex I’m afraid I can’t fully offer a diagnosis from the info alone, but I can tell you that if it’s properly sealed, it shouldn’t be leaking from water within the shower structure. Realistically, you’d even be okay to not deal around the actual pipe so long as the spout is installed correctly and the spout is properly sealed to the wall. However, it is still good practice to seal the hole.
@@two7plumbing I understand. thanks
Is it the same to replace the seal on the handle above also?
Repairs for the handles and stems/cartridges above are not always consistent. You’ll need to verify the manufacture as well as the exact problem and go from there. Typically, however, it isn’t the same repair as shown here.
Any silicone can do it ? Or it has to be waterproof?
Waterproof would be preferred if available
What do you do if the oring in the spout got nerfed in the install. How do you get the oring in the groove on the spout feed tube
This will depend on the specific brand and style that you are using. Make sure you have a clean cut on your copper line. Most brands will slide right on, though you may need to first check to see if yours needs to be loosened to leave play for the oring.
@@two7plumbing I was actually referring to the o-ring literally inside the spout tube. It comes new in all slip on spouts that I have seen. I followed instructions and cleaned the copper tube and cleaned it up and used some silicone lube and when I slipped it on the o-ring that's in the plastic tube inside the spout came out and it's all angled in the plastic tube and I'm trying to get it back in place so this spout can be used. Specifically this is a Danco slip on spout with diverter and personal shower head feed.
Honestly, the problem is likely with the product itself. Danco is a low quality product that is immensely frustrating to work with. I actually refuse to install their spouts as they run a very high risk of immediate failure. Many of theirs also require you to tighten the spout to the piping in such a manner that you can damage the pipe itself if you aren’t very careful. I would recommend going with a better quality product such as the Moen used above.
water is coming out and up out the back of my tub spout. that's not normal, right? I just noticed it today. I was afraid water might be going back into the wall. If I re-sealed it is that all I need to do or do I need to replace the tub spout first? there's no seal at all. TIA!
kafaya77 so when you run water from the tub spout, it’s leaking out the back?
@@two7plumbing mine is leaking at the back is caulking the solution to the problem?
@@vaneese85 if it’s leaking water from the back of your spout when the tub or shower is in use, this would indicate a failure within the spout itself. In this scenario, replacing the bead of caulk shown in this video will not be sufficient. You’ll need to remove the spout and address the issue accordingly (often by installing a new spout).
What type of caulk do you recommend for this?
It depends on the application at hand. If the home has occupants who ate more likely to be rough on the spout (children playing in the tub), I'd use 100% clear silicone as it'll flex a bit easier than caulking and will hold up a bit better. If this isn't a concern and the spout is nicely positioned against the wall of the tub, any white caulking would be fine and tends to look much nicer if applied well
@@two7plumbing Thanks. We are trying to redo the face plate and spout. Have read different things about leaving the bottom side uncaulked. Would Kwik Sweal Kitche & Bath be okay? Thanks
@mogtrader8 yes, that product would be fine. I recommend leaving the bottom portion uncaulked (from about 5 to 7 oclock). Water won't be able to get into the wall from that position and it will help to allow water from a leaking connection within the spout to escape into the tub instead of ending up I'm the wall.
@two7plumbing Thank you very much. We hope it goes smoothe.
@@mogtrader8I'm rooting for you! Feel free to reach out if you have any questions along the way.
Do you caulk the value trim too ?
Great question! This depends on the application at hand. Most valve trims already have a gasket on the backside of the trim which deters water from entering into the wall. For this reason, I do not typically caulk around them. However, if the trim does not have this gasket and/or if it is installed on an uneven surface (such as a deep grout line) which may prevent the gasket from fully sealing, I will go ahead and caulk around them too.
@@two7plumbing wow thanks for replying!!
Based on what you mentioned, I’m thinking this one KES Shower System 12 Inch Rain Shower Head with Handheld Spray Shower Faucets Sets Complete Pressure Balance Shower Valve and Trim Kit, XB6230S12-BK, doesn’t have one & need to be caulked?
@Kristine B I’m not familiar with this specific system. You can always contact the manufacture and ask them to confirm or you could just caulk it anyway. It won’t hurt to do so.
How long does it take to completely dry
Depends on how much is used, but I generally recommend my customers wait a couple of hours before use.
What’s the stuff called you used
Are you referring to the caulk?
Better chance the leak is in the spout going backward in the wall
This is a possible location of a leak. Though in my personal experience, it’s definitely not the more common leak. Failed seals at the wall are notorious for allowing water that trickles along the shower wall to leak into the wall. I see this almost every week.
Though I will agree that if you’re using a cheap quality product, what you’ve stated is going to be a high likelihood. Many of the cheaper versions don’t seal properly to the pipe and will leak from inside the spout. This is why I’m highly selective about the products that I use as well as the products that I recommend in my videos.
Im a cheap ass
That’s okay. Admitting it is the first step to recovery ;) jk
Lol
Hahaha, a plumber giving advice on what to do to prevent calling one.
Yep! Not everything is worth our time. Just as I don’t really want to block out a section of my schedule just to put a bead of caulk on a spout, many people would be appreciative to not have to pay the service fee for a bead of caulk. Win-win in my opinion! :)
@Supa Trending Daily I would love to find a good and honest handyman. Unfortunately, in my experience every one of them I’ve come across does work they aren’t licensed to legally perform and end up causing problems. I’m certain there are good ones out there who are ethical and knowledgeable so this isn’t a blanket statement against them, but sadly I’ve been unable to find them.
Not wise to use a utility knife on or around the fixture. DAMAGE ! To either fixture or tub wall. I would want to hire someone more meticulous in their work.
Nothing wrong with using a utility knife for this situation. In fact, they now make utility knives designed for this specific application (I own one, though this tool wasn't around at the time this video was shot). I do agree, though, that it wouldn't be wise for someone to use a utility knife for this if they are not competent in the tools they are using. May I ask what method you would use in this situation?
Nice simple fix. Being skilled with all kinds of tools goes into being a tradesman or DIY guy. Common sense goes a long way. Nice repair!
@@mitchh6702 thank you!