Stop Using Cordless Hammer Drills...
Vložit
- čas přidán 7. 09. 2024
- Stop wasting time, money, and working less efficiently using cordless hammer drills! We give you all the reason to move past this relic of battery powered cordless tools. We let you know why you should stop using cordless hammer drills and how to get your construction projects done right and what to do after you make the right choice!
Join this channel to get access to perks:
/ @vcgconstruction
I'm an electrician and I'm often not going to need a rotary hammer during an entire week. But I will be drilling multiple holes for tapcons. In that case, it makes more sense for me to have a hammer drill, and when I really need to bust up some concrete or drill huge holes, I'll break out my corded rotary hammer. But that extension cord is more cumbersome than carrying around a (little) extra weight on my drill
As The Carpenter, i rarely agree with the electrician. But you got this one bro😎👍🏾
I'm also an electrician, this was literally my response I was coming down here to type.
I'm an electrician, and I completely agree with you.
Exactlyyyyy
@@SuitGeoff Same here, lol. I run conduit regularly on brick walls. The ironic part though is that I have DeWalt SDS drill and a drill/driver😆. But only because I was given the DeWalt drill as a gift from my daughter. I didn't have the heart to tell her I need a hammer drill.
I love the rotary drill though. Especially the "chisel" setting that I thought I would never use
As a concrete artist, I drill tons of 5/32" holes, in 1.5" thick concrete. The cordless hammer drill has revolutionized how I work, because I don't need my giant rotary hammer, but I can still blast through hundreds of holes. No other tool matches the versatility for me
Depends on the trade and what you do. But for me it doesn't hurt to have that extra versatility. As an electrician sometimes you gotta install conduit and smaller equipment on concrete walls with 1/4" anchors and you don't need a full size rotary drill for a 1/4" hole especially a couple holes. Anything larger you need a rotary drill.
I agree. Its is electricians I do see using the hammer drills the most. And you have to think if you are up on a lift working and need your drill driver anyhow why do you want to take another tool (rotary hammer) to drill a couple holes to attach some stuff to block? When talking about weight that would be more than just a drill driver with a hammer drill capability.
Agreed, definitely the sparkies using these the most, I’ve even seen them putting tapped holes in concrete for threaded rod for hanging GSTs
As an electrician I can say this is accurate. Got a dcd999 and I love it
Where I’m from, we have something like 90% concrete structures due to tropical storms. That number includes most homes. Being a DIYer in a concrete home, a hammer drill makes the most sense to me for its versatility. I totally get that for most people a hammer drill is unnecessary. I just used mine over the weekend to do something as simple as hang new curtain rods. Definitely a necessary tool for me.
For concrete a hammer drill is the most stupid thing. A rotary hammer is milions or even bilions times faster, and also milions times more reliable. And also the SDS bits are wey-wey-wey more reliable only with a hammer drill that is using a moderate RPM with wey higher impact, with less friction that heat up the soldering of the carbide tip...
But there is a use for hammer drill - for drilling brick wall a little faster then with no hammer and without cracking the bricks with a rotary hammer.
@@loochan325 you are absolutely right. A rotary hammer will out perform my hammer drill every day of the week.. but as I said, I’m not a contractor or tradesman. I’m not drilling 500 holes into concrete every day, so that time saving isn’t worth the lack of versatility to me. I don’t feel like my hammer drill takes long enough through concrete to warrant purchasing a rotary hammer, not to mention the additional bits. Even if I did, I still use my hammer drill on material other than concrete so I’d be using it anyway.
Hope this helps to clarify.
IDK buddy, I am a contractor and rotary is sexy, but who wants to pull out the big guns to hang shutters. Or a shower door...
@@jasonzoretic9239 exactly. I have some needs that I use rotary hammers for myself having two at my shop. But for most everything the hammer drill (15 year old Milwaukee m12 brushed hammer drill/driver) works excellent for the occasional fire extinguisher hanger installations or white board hanging.
@@loochan325 not every task requires a rotary hammer. Sometimes for drilling small holes or drilling in concrete blocks, you don't need a rotary hammer.
So why use the big tools ( I have SDS plus and SDS MAX rotary hammers) when you can use the smaller tool that is very capable for the job?
As a DIYer/non-pro, I opted for the hammer drill option because 1- my smaller impact driver gets used the most, and 2- since I don’t use it that frequently , I wanted to have the capability if needed. 3- the size/weight difference was minimal.
This guy is definitely a Milwaukee salesman
I prefer an all in one drill solution like a cordless hammer drill. The cost and weight isn't that significant and I drill a lot of holes for Tapcon screws. A cordless hammer drill is the right tool for that job.
I’m not sure where this video was going. I use m18 hammer-drill on tiles in customers bathrooms. These bathrooms cost anyway from 10-50k plus. You can’t come in there using a rotary hammer drill risking damaging porcelain,marble, granite, quarts and ceramic. You have to be a professional and use caution while using the best tool for the job.
I definitely agree that there are more specialized tools that will do the job better.
However, the hammer drill fills one specific role for me personally, it's versatile and I don't HAVE to carry an impact driver and an SDS drill, thus saving weight and space in my tool bag/belt.
At my job sites we are usually moving around a lot, nd getting very far from the car not knowing exactly what we're getting into, the hammer drill I find is perfect for that, it's light enough to have on your belt, can drill and screw in fasteners (gently and silently too, which the impact can't).
Basically it is as you said, the jack of all trades, master of none. And that's exactly what I need.
I have considered only carrying an impact, but I often do work where gentle fastening of screws is needed, and the lack of a clutch setting and extra noise on the impact just makes it fall short.
I feel like the video doesn't really understand the point it's trying to make. It's like he's arguing that instead of carrying a Leatherman, you should carry a hunting knife, pair of Knipex pliers, and a full set of fixed-blade screwdrivers all the time. Like... duh, those tools are better. But the whole point of the tool that combines them all into one is that you are trading some part of the utility and additional cost per tool, for a smaller package that does it all.
If I have to add a plastic anchor or 1 tapcon to something hammer drill is fine. Anything more or larger and sds plus comes out.
I've got both, I'm in trades, the issue is that a rotary hammer tends to break bricks a lot more often than a standard hammer drill. That's why I keep both. Punch a hole with either one but in certain situations a rotary hammer is too aggressive and the old stand by is the best choice.
Hi Vince, IMHO it all depends on the type of construction in the area you live in. In my area most house constructions including the rooftop are made in concrete, masonry, rebar and cement blocks, it's a must on any drill. I live in a hurricane prone area PR. But up in the mainland I have to agree with you because I've seen the type of construction they do and mostly with wood, cement boards, gypsum boards, OSB ect.
Appreciate the feedback Anthony!
I live in Miami and this is certainly my experience as well. I've been putting lights into the wife's new office recently and the ceiling is concrete.
I look at it this way. Hammer drills are not that much more than drill drivers. We have a lot of old brick buildings in my area and they always need a small hole to hang anything. Better to have it and not need it than to not have it and need it in a pinch.
In some battery platforms, the hammer drill doesn't have any more weight nor size than the standard drill. Yet it provides a higher rpm, torque, and unique features than the standard drill in that line. So having that extra function when you need it (and some of us actually do need it available without having to reach for a different bit of kit) makes it a no brainer to have the function available. Also, I carry the 1/4 impact driver as well. Depending on the job, both can be the right tool for it, and sometimes, one is the right tool where the other will destroy what you are working on.
Go Vince!
Your Wrong!
I pull it out when I need to use hole saws 1"+ and the occasional need for the Hammer Drill function.
I chose this instead of the regular Drill/Driver for these reasons. I get Drill/Hammer Drill.
I also have my hex Impact I use as a Drill/Driver with Spade Bits. Can't do Hole Saw with Impact.
Also good to have both to use at the same time to keep from continuously changing out bits for pilot holes.
Just drill & drive ambidextrous, lol.
👍
Well appreciate your input Redd, thanks!
I'm a service plumber and my hammer drill takes care of what little masonry drilling I do with ease and having the adjustable chuck vs sds specific bits is also very convenient.
I actually need the hammer function for my use case. I install window hardware for storm boards on new homes. Lots of them are stucco so theres a layer of mud i need to go through, I also run into nails every now and then. Definitely don't want to be lugging around a heavy rotary hammer for 15-30 windows, drilling 60-120 holes, especially when some are over 12 feet high. After that im putting in 5.5in lag screws with my impact. Wish i could only use one tool, but even if there was one, it would burn out from all the hole drilling and lag screwing. They both can heat up quite a bit on hot days.
Hammer drill is nice for small anchors and when a rotary hammer may initially chip out your concrete/brick/block. I've had to put tapcons in old brick and the rotary hammer I had was too aggressive. Went to the hammer drill for the rest and it was smooth sailing.
these drivers are very usefull for bricks which are very common in Europe, most SDS drills go to hard and damage the bricks whils these hammerdrills do a terrific job at it. And in Europe a lot of carpentry involves brickwork so for me it is the only type of driver I have (got a few but multi purpose bits).
This is it for me. Many times the blowout on the back side of a rendered brick or block wall from a rotary hammer is a huge inconvenience for patch work. You could take the time to pilot hole it with a much smaller bit and then use the actual diameter bit on each side of the wall, but that's time consuming and also not always practical. I also hate doing more damage than is necessary personally. And I don't think you can get away from that with a rotary because it relies on that increased force/IPM to drill faster.
When we need to drill a lot of holes in concrete, we get out our old corded SDS drill, If its just 1 or 2 , less than 1/2 inch, we will just use a cordless hammer drill. For SDS jobs, we always throw in another bit of some sort with each job we use it on, its a good way to get stocked up on bits.
Fair enough , appreciate the feedback Chuck!
Hey Vince, as a remodel and maintenance person. It helps to have a hammer drill. Example- I own a bosch bull dog corded. I would have required more drywall to be removed when replacing a bad or rotten bottom plate in a bathroom. The old anchors or nails were rusted down to concrete. Just made new holes and set anchors. Quicker easier and had the driver function to tighten the nuts down. Did not have to carry two tools, or mess with cords. Saved me time. I'm sure there was a faster way, just working with what I have. With that said, I was impressed how fast gen4 hammer drill performed. Gen 3 was meh in slabs when it came to that. Keepem coming love the content.
I think it depends on the person and what jobs they need to accomplish. Some people may prefer using a hammer drill over buying a SDS and all the specialized bits you would need. Maybe you already have a whole set of drill bits of different sizes that only fit into a chuck. Maybe an M18 hammer drill is just the right amount of power and size for the job. The installation driver may be under powered for what you need. That's the beauty of having many options, it caters to the individual. Thanks for the insight Vince!!
Thank you BG
@@VCGConstructionNo, thank you Vince. That was a poor reply to BG. I'm 100% with him on this one. I own an sds and an sds max corded hammer drill. Only way to go if you're doing repetition drilling. My cordless rotary hammer is great for a lot of midsized jobs. That little hammer drill feature on the regular drill has saved the day close to 50x! Installing a septic drain field... The chain for the concrete cover needed to be affixed to the concrete tank structure. 2 - 1/4" concrete anchors. Come back the next day? No. Use the hammer drill feature, get it done and call it a day.
Sudden rain and had to plastic up the window openings. We weren't the general, but it was the right thing to do. 8 tapcons were needed on 2 windows. You guessed it, hammer drill feature on the drill. Saved the day.
Many more instances. I drill all my wood holes with it anyways. What are you saving? 10 ounces... probably not even that much. First time I'll say this, Vince don't dig so deep for content. SMH
@@edpoints1127 Milwaukee was probably seeing low rotary hammer sales that month, so called up Vince to convince people to spend money on tools they don't need.
I do remodel construction. I have a rotary hammer. It mostly collects dust. My hammer drill is on every job and as you said, is the one that gets the job done quick and easy.
Vince is over here pretending new construction commercial builders make up the majority of his viewership. Not even close. Most folks watching these videos aren't spending days on end, drilling big holes in concrete. I'm not hefting out a rotary hammer to drill a few holes in some stucco, brick, or even concrete - when all I have to do is flip a switch on my drill. It's hilarious that he talks about how "very heavy" a hammer drill is and then recommends a rotary hammer. What?!
I'm an electrician in a hurricane-prone area so all houses & buildings are of concrete/block construction. While I do carry specialized drills for given tasks when I know what that task is beforehand, however, the hammer drill is my EDC which allows me to carry fewer tools to my basic call-out jobs.
I’m a fiber and low voltage installation technician, and the hammer drill is used when needed. IE. making holes in mortar. The impacts can do it, but not as quickly as a hammer drill. I know what you mean, but it does have a purpose on my truck.
i cant say i completely agree, but you certainly do make some very valid points. i really cant argue anything you said, but sometimes ppl have different priorities and the trade offs are acceptable.
Vince certainly gets u thinking ...whether u agree or disagree.
I would actually disagree. For residential contractors who do renovations, its just too versatile to pass up. Having a single tool that can mix small batches of mud/thinset and drill holes in masonry/tile is an absolute win. For the size of jobs we did, having dedicated solutions would have been massive overkill and, honestly, a waste of money.
I use the hammer function often as a fiber technician. But I tend to use my m12 drill/driver for drilling most holes in wood and only pull out the m18 hammer drill when necessary..
I use mine for tapcons and driving large timber and structural anchors, and it’s the best heavy duty drill for large holes 4” plus for duct work. Everything else impact or compact drill
I learned this the hard way. I tried using my Bosch with a 6v battery to hammer holes in concrete/ masonry and was very disappointed in the failure of the tool. Luckily i had my trusty Makita corded Jammer drill to get the job done. The Bosch became my go to regular drill driver.
I rarely ever use the hammer function, this is true. But I do like having it when I am drilling into masonry. This is only because as a DIYer, I haven't purchased a dedicated rotary hammer yet. I have used the M18 rotary hammer, and it by far destroys the abilities of my hammer drill for sure. But it's just not worth it to me to go out and buy one when my hammer drill will get the job done, but slower. (much much slower)
I’m a handyman. Why carry a bag with 3 tools when my hammer drill will do all of these jobs. It’s not enough heavier to wear me out. It actually saves time by not have to go get another tool or carry multiple tools on my belt when I’m 8 feet in the air putting anchors in a brick wall, and then need to drive the screws.
I don't know why Vince is trolling hammer drills 😂, but Im a cable installer in Florida and more than 90% of the homes I install onto are masonry. I started with using a non hammer Craftsman. Totally changed the game for me when I upgraded to a Hanmer. It's not even a contest. Hammer is a must! Then, I use/carry my impact to drive the fasteners once the hammer makes the hole 🕳️. I'd rather carry my impact than unchuck and change bits to drive a 1/4 Nut tapcon with the hammer. So, I carry both.
Hammer drill does everything , I stand by it. I’ll bring out my SDS for maybe once in a while
I've just bought the M12 Rotary hammer. When I'm drilling in a concrete wall I want that thing to hammer and not to gently vibrate it self through. But I mostly do drilling for 6 and 8mm, so M12 is the perfect specialised tool for the job.
I'm an electrician who works in residential new constructions. My impact fastens and my hammer drill makes holeys. Between my M12 impact and M18 hammer drill I can do anything. Using spade/augur bits on an impact is fine but if it hits a nail it will destroy the bit which my hammer drill wont do. it just stops.
I’m an electrical apprentice and I will say that yes you make a very good point BUT as you know, there’s always going to be that one or two times where you’re going to need a hammer drill so it just makes sense to spend the extra little $ to save yourself time in a pinch
Sure came in handy when my wife needed 4 holes in her glazed ceramic pot. Don’t use it often but it keeps me from going to the shop to get my Bosch corded hammer drill MOST of the time.
I use a hammer drill for drilling small holes in tile but I also own all the different styles of drills you spoke about. also a hammer drill will work when you need to drill holes for a few tapcons unexpectedly if you don't have a rotary hammer with you.
As was mentioned - you will use the hammer drill function for tapcons, and drill less than a couple concrete holes. If you’re drilling more than a couple of concrete holes you’re going to want to use the rotary sds.. every tool serves a purpose and for lightweight concrete drilling and or concrete tapcon mounting ect.. the hammer drill is excellent!
Thanks for another great video and not being scared of sharing a well-founded opinion!
My first reaction was to disagree with your statement. As a DIY enthusiast and sort of amateur Jack of all trades, my experience with my hammer drill is beyond positive. Besides drilling into (hard) concrete, I'm able to perform all kinds of tasks with this versatile tool. I think I even don't mind the weight issue, while I'm often using 1.5 or 2aH batteries.
However, nowadays I more often grab the more specialist tools when taking on bigger projects. When working all day on a renovation or any other type of project, it totally makes sense to be able to grab the specialist tool and switch tools to fit the needs. Why drill a hole with with your hammer drill and then switch bits to drive a screw into something?
I carry a hammer drill and a rotary hammer. Sometimes the rotary is far too large to fit in some spots. Sometimes I don't want to lift a heavy ass rotary overhead for a couple hours at a time. Some anchors are so thin that a large bouncy rotary hammer will wallow out the hole as you drill and ruin the hole or force you to move your hole and change your layout when a hammer drill wouldn't. I run into this a lot with tapcons in particular. I'm an industrial mechanic by trade and have set 10's of thousands of anchors and have come to the conclusion that you need both to actually be efficient.
As a electrician I think the hammer drill has its place, often times I’m hanging one or two boxes on a concrete slab and have to run conduit to those boxes. So I need to be able to drill 1/4” holes into concrete to put anchors in so I can mount my boxes and straps. Yes the rotary hammers are nice and I have a small one just for this stuff but Sometmes I’m parked far from where I’m working and if I’m only drilling like 4 holes it’s nice to have that function to save me time from walking back to my work van
Yo Vince! As a drywall punch out guy (for those who don't know what that means, sorry about your luck) the instant versatility of a hammer drill to drill/driver is priceless! One never knows when drilling into a slab one minute, then fastening track and studs into that slab the next minute, might be necessary. I swear by the hammer drill/driver. Though, these days, the installation drill is an awesome addition to a punch out person's arsenal. Thank you for the topic and God bless! 😁👍✌
Yes!
BOO-YAA!!!!
Interesting point Vince. If it's a lot of driving, I use my bulldog. But for small little things, it's straight to the m18.
I ice fishing a lot and a hammer is a must to drill 8 to 10 inch holes I used a regular brushless without the hammer once and it struggles
I mainly use my M18 for drilling wood up to 1"holes with auger bits, 4⅛ & 6⅜" holesaws, and the ¼" masonry bit on hammer mode.
If I need bigger, deeper, or more, it's the SDS & HoleHawg all day.
Otherwise it's my M12 impact or M18 impact.
If I know I'll only need a couple small holes drilled, wood or fenceblock, I'm using the tiny M12 impact that fits almost anywhere
Just got the gen 4 hammer drill. I have an older brushed m12 drill/driver set. They can handle 80% of what I do around the house and restaurant. But I have the installation driver for doing shelves and random stuff. It's an awesome standalone drill. Has entirely replaced my old brushed m12 drill.
But the restaurants pre-fabbed with metal studs. And getting through those is a pain in the butt. Also occasionally have to punch through concrete or brick for running speaker wires. So I decided to just go ahead and invest in a drill that can do all that without cutting out. I don't think I need a new m12/m18 fuel impact until my old brushed m12 impact dies.
Starting out in the trades field it makes sense to use the hammer drill. Having no tools and starting to build up I prefer a 1 in all. As I get mo money I may go into lighter more expensive tools
Been from Puerto Rico where 95% of the structures are made of concrete (yes, even roofs), you’ll even need a hammer drill to hang a framed picture on your wall lol
I use a Milwaukee cordless 18v Hamer Drill when I drill holes in concrete for TapCon screws. The Hamer action combined with a good quality masonry bit works way better than an impact or regular drill...
As a multitrade. I'm always trying to streamline my kit. The standard box I carry now only has my M18 Fuel Impact Driver. I'd never drive screws with a hammer drill because the impact is so superior. And drilling with good impact compatible drill drill bits is also superior. There is a little more play in the bit, but that compensated for by less vibration were accuracy is concerned. Anything the impact can't drill out with a multimaterial bit on full speed is a job for the sds. The bit change is fast for instances where I'm drilling a countersink, then a plug hole, then driving the fastener. My hammer drill is obsolete. I'll probably replace it with an M12 impact. What would be useful is a clutched attachment for delicate work and drywall, but the trigger control is good enough for now.
A jack of all trades may be a master of none but I'd rather a jack of all trades than a master of one.
I use a hammer drill all the time for everything and I always have masonry bits in my backpack at all times. I mostly use smaller masonry fasteners and I don’t have to make the extra trip to the truck to get a hammer drill, because I already have it. If I’m doing bigger holes in masonry then I go get my rotary hammer drill and drills.
I would say that almost everyday I will use the hammer drill function at some point, it’s just the type of work I do.
It's better to have one versatile tool, than having to carry several different tools.
I rather have the specialized tools, hell, I have the specialized tools, but in a pinch, I rather have the rotary drill lol, my friend, everything is block and concrete here in Puerto Rico, if the drill doesn't have hammer on it to save my ass in a pinch, I don't want it lol
Definitely
Vince, you are correct. This is why I strictly use Flaced tools
As a locksmith I love having the M18 hammer drill handy at the flip of a switch for light hammer drilling about two percent of the time....I already know I'm going to plug in the REAL Dewalt corded hammer drill for heavy hammer drilling installations...
I use both a hammer drill and a rotary hammer, I use my hammer drill for installing small 5/32" tapcons and such, and save the big boy 1-9/16" rotary hammer for breaking up concrete or tile
Concrete. Nuff said
Yep 110% That’s why separate tools are sold. Rotary hammer is the only way to go!
You're not wrong in the minimal usefulness of the hammer drill feature on cordless drill drivers, but the non-hammer drills available from Milwaukee in particular are non-Fuel and poorer featured. Most of the time, the only hammer drill activities I'm doing with my driver are small 1/4 or 3/8 inch concrete anchors for decks and ramps. For me, the combo tool is worth the extra weight because my corded hammer drill isn't taking up space or having to be accounted for at the end of the work day. When I know larger (or deeper) concrete holes need to be drilled, I'll take my corded hammer drill with me, but when they aren't, the space savings and easier inventorying makes the extra weight of the Fuel Hammer Drill Driver worth it for the versatility of that tool.
As an Electrician the hammer drill works great for putting tap cons in. I strap conduit to block walls all the time.
I specifically use my impact drivers to drive screws and lags, my SDS Plus and Max to bore or drill through concrete and my drill to drill holes in wood and metals.
I would argue that an impact only does a 1/4” bit. A hammer drill has a chuck that can adopt adapters, bigger bits, uni-bits, hole saws, you can even make your own bits and the chuck will adopt it
As a concrete guy hammer drills are an awesome tool we wore and nail a lot of forms and a big rotary would be heavy bulky and likely break the small bits alot
It make sense, since this channel primary audience, I believe are from USA, where many constructions are done using timber.
In other part of the world, such as Malaysia, 80-90% of the houses are made of bricks and mortars. So, hammer drill perfectly make sense.
Been working in construction from foundation to finish for 2 years now and have done personalized homes to comercial buildings...when im on a larger site and further from my tools, or working up high, I prefer to carry tools that can get most of my jobs done...I dont want to get weighed down by a bunch of tools, be running around more than necessary, or have more tools to carry up and down ladders, staging etc...hammer drill is the quick and dirty do all for anything that is gonna get covered up that can easily fit any bit/ doohickey i need. However i will say my impact gun is more comfortable to use in more situations
M12 Surge with a 5.0ho and Bosch 12v Flexclick. Can’t beat the quality in both, I highly recommend them
I'm a homeowner. I have larger 18V cordless handtools that include a hammerdrill, but have recently been adopting the Milwaukee M12 system for working on my cars. The M12 system is so lightweight and convenient that I've been using it for most things, and I'd go for that M12 multi-head installation driver before their compact hammerdrill for the exact reasons in this video.
damn it Vince. I wanted to say you are wrong... but you're right.
I just did (6) 5/16 holes to mount a TV in a cement wall today. I missed the rotary.
I build and install wrought iron gates and fences. We use a corded hammer drill for every job since we always have an extension cord ran for our welder. But in the cases where it’s a quick install and don’t need to unload our cords we do use our cordless hammer drill for drilling into concrete, brick walls, and through stucco to install our anchors. Don’t really see the need to buy a dedicated cordless hammer drill so it’s worth the cost to me to have the hammer drill function on my regular drill.
So your advice is dont use a hammer drill because it is heavy. Instead, use the more expensive, more heavy, less versatile rotary hammer ? How is that logical lol
I do cabinets and trim work and I'm currently having this debate with myself. Most of my jobs are done in less than a week so for me, I like to have as little of tools there as possible. I hate using the hammer drill for drilling holes in my cabinets as it is super heavy, hower sometimes I do need to drill 1/4" holes in concrete to secure toe kicks, end panels, etc. I hate the idea of carrying a roto hammer all the time to use it once a month, however I also hate having to use a hammer drill all day every day to drill small holes that the M12 drill driver is more than capable doing.
Funny… I remember a time when someone on our jobs would get upset with the noise of the impact drivers and wanted us to use drills 😂😂😂
Whhaaaaaaa?
@@VCGConstruction 🤣
I work at a welding/fabrication shop that does some mechanical contracting and use my hammer drill frequently running anchors into concrete and block. I use my sds cordless when doing bigger wedge anchors but the hammer drill is awesome for smaller tasks that just use tapcons. I’m talking specific jobs where I may put in less than 10-20 tapcons on a jobsite.
I’m a low voltage alarm tech and I use the hammer function everyday. Drilling into stucco for external cameras and doorbells.
I'm gonna be straight honest here, i have a milwaukee m12 hammerdrill, and for me as a service electrician, i can do everything with it from concrete and bricks with the hammer function to drywall. i can do it all. it is a differend discussion for when i am working on a construction site were I have to drill bigger holes through Deeper concrete walls. at that point i am switching to the m18 rotery hammer. one downside is that is it so freaking heavy, so drilling in a place that is JUST about to be out of reach can be pretty hard.
I'm a warehouse technician who also does construction for the warehouse as needed (under a jack of all trades & master electrician who's also been a forman, superintendent, senior superintendent, and inspector). I don't really find myself needing to do stuff like coring or anything. Even drilling holes into concrete all day, it's usually for tapcons and anchors, drilling around 3/16" holes. I don't generally have a use for a rotary hammer, nor do I or the shop own one. My hammer drill isn't as fast as a rotary hammer but it does just fine. That and an impact are with me every day, as well as a handful of other tools as needed.
I use that hammer drill for tap cons in brick and block all the time. The one drill can drill holes in studs and then tap cons in block. Maybe i'm not a "real tradesmen" hahaha just a licensed electrician with a LLC company.
Also an electrician. It’s hard to beat for drilling for tapcons.
I invested in a cordless rotohammer because my hammer drill didn't have a hammer only setting. Now that I have it, I don't anticipate ever using the hammer setting on my hammer drill.
The video and the comments are really interesting. I'm not in the trade, just a casual observer and occasional DIYer but great to listen to everyone's ideas and to see how the tool world is changing.
I have never used the hammer drill function on a drill/driver. I always go to the sds simply because it’s a lot faster. Especially when drilling large holes like 1/2” and 5/8” as we do for our pole sheds and the large anchors we use
As a mechanic I get the most use out of my M12 1/4 hex impact driver, than any other power tool. it's lighter & does about 85% of the work load. So I see where Vince is coming from. Not once, have I ever had to use the hammer function on my drill!
I have the drill and impact in 18v for work and 12v for home. The 12v models work on everything I would need them for at home and I'm confident it would handle my job, minus the capacity. I just don't like getting my home tools nasty.
Yea, you clearly aren't thinking this though. Why carry 2 tools when you can use one tool to do to separate jobs. That's why our company uses hammer drills.
I’m a home owner, DIYer, couple odds and ends sides jobs, kinda guy and I will always own a drill/hammer drill combo. For drilling tapcons ect it’s all I need. That and my impact driver are the perfect combo.
You are absolutely right. Hammer drills suck. Especially for drilling concrete. That's why I own light cordless lithium drills and drivers and a corded Bosch Bulldog Roto-Hammer.
I've been in the skilled piping trades for going on 15 years now. I can honestly say that I have absolutely zero use for the hammer function on a drill driver. Things like the Shockwave impact Duty attachments for Milwaukee allow you to check up an impact drill for most drilling applications your hole saws would be one of the few things where I would use an actual drill driver but never on the hammer function. And then when it comes to stuff like concrete I've never used a hammer drill, I've always used the SDS rotary hammer. What a waste of time the hammer drill would be. MUCH LOVE. great video
A cousin of mine wh9o has worked on construcion most of hi life as a woodworker always says "You're as good as your tools" and he is 100 percent correct. I'll say one thing though. Yesterday, I had to do some light work, and instead of using a drill and impact driver, I used the impact driver to both drill and fasten. I think for around the house, this is all I need. I'll save the M18 and M12 Fuel drills for more intense work, or to hand off to a worker doing a job for me when I think their tool is inferior.
Vince, I work as a handyman, a jack of many trades and will tell you that I need tools that are kind of like me. I only use the hammer trill function when drilling through brick or concrete with masonry bits. I think using the HD function for anything else is moronic. Who tries to drill a precision hole in wood with a hole saw or spade bit dancing around. With the HD function my 4 year old DeWalt XR drill driver goes through most brick and masonry like a hot knife through butter. I've tried the same without the HD function and it was like a cold knife through frozen butter.
If you're a homeowner that hammer drill is the only drill you need. If you're a pro and need to go to a rush job and don't have a truck full of tools, grab that hammer drill and it will get whatever job completed. It's not the best tool for ever application but it can get the job done whether it's boring holes thru wood, drilling into concrete, or installing fasteners
I am an electrical construction worker in Korea. In order to use a screw anchor, we have to drill a hole in the concrete with a diameter of 6 to 6.5 mm, and use a self-drilling screw on the metal plate to fix the steel box or steel support at the same time as the drill hole. I think it's really inefficient to have to bring both a drill driver and a rotary hammer drill for this job every time. All it takes is a 14.4v hammer drill. A rotary hammer drill is required only when drilling a large number of holes with a diameter of 10 mm or more. Since you are a carpenter, you may have posted this video without understanding the peculiarities of these various professions. You only know about your work.
But those two "compact" tools take up more space and weigh more than the hammer drill does.
I'm a DIY Hobbyist I don't need the specialised drills and bulk of it all, so hammer drill is perfect for me for doing IKEA furniture and sometimes using the hammer function to drill into walls.
when you are an apprentice it's a good tool to fill in where you haven't gotten the specialized tool yet.
I work for a cabinet shop and a hammer drill, an impact driver, and a right angle attachment are my go to’s. I never know what I am going to find on the job site, and why take more tools than I need? Are there specialty tools that might be better at each task I need? Yes. Do I want to buy and carry all of them when I have enough I have to take to a job site as it is? No
I use the M12 impact driver with a 5amp battery all day long as an HVAC tech. Now that said I forgot my drill even had that feature till it was accidentally turned on. Lol if I need to drill any masonry I use my 1 1/8 Milwaukee rotory Hammer. I usually only use that when I am helping out our plumbers.
I’m with you on this one. I definitely try to plan out the job and bring the appropriate tools. Especially when drilling and fastening into block and concrete. My M18 hammer drill isn’t my go to for that. I have used it in a pinch for drilling concrete when I needed to but it wasn’t the specific reason for me purchasing it. It’s definitely more than capable, but I’ll default to a rotary drill for that task. Great video! Have a great night! 👍🏻
Shout out to u and vcg lol
Around the house I use a DeWalt Atomic Impact Driver for most tasks. I use a normal Atomic Drill for drilling holes into studs or woodworking projects where I need accurate slow holes made. 90% of the time I use an Impact driver for most tasks.
I’m an electrician who needs to carry tools that can accomplish a variety of tasks from site to site, room to room. And at the end of the day they have to fit in the back of the ute. So for me a hammer drill accomplishes what I need day to day in Australia
I agree a hammer drill is not the same as a dedicated rotary drill BUT for a while I could not buy a dedicated rotary drill and the small jobs I was doing my m18 hammer drill was getting the job done. Drilling 3/4x8" size anchor holes for post and whatnot, it served its purpose and got the job done, now I have the fuel m18 hammer drill big boy and its truly much better at drilling through concrete but if need be I can go back to my hammer drill and assist in any job of space is a issue.
It's good for tapcons into foundation, and boaring wood out the 2 inch holes for the pvc, the two things I use it for. So its perfect for me. I use my SDS max for the masonry.