JAWA 2-stroke power tuning (part 3) - new clutch
Vložit
- čas přidán 28. 02. 2022
- Welcome to this little insight of how the clutch system of my 350 cc power vintage JAWA has been improved. With nothing / no solution from another bike on the market I was forced again to help myself by re-designing some major components to make it robust enough to cope with more than 30 #twostroke HP without any visual changes to the clutch side engine cover. Yes, that’s the point. Certainly there would be even better and more modern technical solutions for a clutch, but nothing from stock fits below this small cover…
Here is a little more information why all of this became necessary:
• JAWA 2-stroke power tu...
• JAWA 350 / 559R 2-stro... - Auta a dopravní prostředky
Love to watch your enginering and how all the staff are going to fit together. Great job!
Thanks Mate.
@@Quiet.Light.Engineering good afternoon, how much does one kit for tuning the clutch drum cost!?
Amazing job, all jawa users facing the gear prblm, now this is the end for this issue.
Thanks for your feedback!
Great content, i watched the other videos of your channel, you have gret skills mate and you sure know how to handle a two stroke! Here in Italy we do a lot of stuff like these on old vespas, somebody manged to overtake 30hp on that small thick frame, quite crazy, so we had to solve problems like yours... clutch bell which easily open in two parts, gearbox shift cruises which breaks and so on...today we have a lot of reinforced stuff on the market made by some really skilled guy, but somebody still does it like you, machinig everything from zero into the garage. I've been into two stroke for more than 15 years and i love them. Last month i found, here in Italy, a rare Jawa 250 californian , white fenders and black\chrome tank , from 1970...a quite rare motorcycle, especially here in Italy. The baby has got just 7000km but needs some repair, a new piston and a new connecting rod , i've already found almost every part. I love this bike since the day i took it with me from its recovery on the outside, mine has got the same engine as your, the 590 with the second type of piston , the one with those marks for the porting on its top. I would really enjoy to make a better contact with you, if you have a social or something similar! 🙏 thanks for your contents , greetings from Italy and from a young jawa owner!
Thanks for your message and greetings to Italia. You can contact me via quietlightengineering@gmail.com
Finally been looking forward to this keep up the good work
I absolutely adore your skills and craftsmanship!
Thank you Obbe.
Very awesome! Love you work. You're like the master of Jawa. Its very fun to see a quite simple, low powered vehicle get completely changed by someone that has absolutely mastered a brand/ model. My own project is a Tomos. I've been modifying the clutch too, cuctom cnc segments, Puch maxi cylinder, custom exhaust, custom welded intake, waaay bigger high tech carburetor. Its just fascinating to absolutely get 100% of the maximum performance out of "old obsolete tech". Looking forward to the next video!
Thanks Mate 👊🏼👍🏼💪🏼
I really like your work aesthetics
Thanks for the nice feedback.
Verzeih mir den Ausdruck, aber einfach ein geiler Typ mit richtig Passion für die Sache! Macht einfach richtig gute Laune dir bei dem Projekt zu folgen!
Danke für’s Zuschauen.
lovely clutch .. simply amazing ...hope it rides great too
Yes, it does. Perfectly smooth.
i'm looking forward to it.
Очень интересная доработка, ваше мастерство впечатляет 👍
Great video. As a czech and owner of many JAWA motorcycles, there are 2 major clutches. Your's original is called 634 small clutch for older jawas. Then there is the "big" 634 clutch, which has some plates more and stiffer springs, is also a duplex, but essentialy is the same as the "small". Then there is the 638 clutch, which is way less reliable, but can be fixed with proper adjustments and can transform much more horsepower. Small 634 clutch can transfer up to 15-17hp (theoretically), the "big" can transfer up to 23hp (my personal experience is up to 26hp, but you have to get special springs and cant do stunts and full accelerations in short periods of time) and 638 clutch can transfer up to 35-60hp. All of these clutches can be swapped with no to low changes to engine, except small clutch isn't duplex. My favourite is normal 634 with stiffer springs, i use it on my 638 engine, which has 23-26hp. New is cheap and lasts +- 100k km before replacment. 638 clutch is the best for tuning and 99% of all racers use it. It lasts up to 150k km and when fixed (look it up, solution is pretty easy), it is better in every aspect than 634 clutch, except some minor issues, which make the difference in normal commuting and that's why is 634 clutch more popular.
Also, modern 4T motorcycle oil can be used, beacuse plates are made from the same material as any other manufacturer uses today. This also helps transfering more power. All hp values here are with factory oil, which is basic 75w90 (don't know exactly), which gets its job done.
Yeah and one note to the clutch hub tolerances. In normal service and commuting, just ignore it. These machines were poorly made and are made to go everywhere. There are examples of 400k km of these engines and clutches still worked. My has 120k km and i changed plates once, 3x springs and 4x primary chain over the years. By normal bike's standards, my clutch is KO, but for jawa, its almost like new. I reccomend looking up 638-640 series, my favourite indestructible jawa motorcycles.
Thanks for watching. Are you sure the bigger 638 clutch fits below the old type 559 / 360 engine cover?
@@Quiet.Light.Engineering it should be OK. Look at bistella 500, it's 10cylinder Jawa with 60 hp and has the same engine block from 350/559. I think only problem is the primary gear, which must be changed to duplex. I ve seen many tuned 559 and many had 638 clutch. If 634 clutch is compatible with 559 and 638 engines, then there should be way to install 638 clutch to 559. I am more to the newer jawas, but I can ask on a our forum, where are really skilled and knowledgeable people.
P.s. salut to you, great skill and dedication.
The larger clutch only fits in conjunction with the (rare) automatic Jawa clutch cover, not the best looking and smooth shaped original one. By all means I wanted to keep this cover. This is why I modified the small standard clutch.
@@Quiet.Light.Engineering you have done great job. If it works, than there is no need to switch clutches. I wonder how much it will last
Do you have any suggestion how to get rid of the vibrating/rattling effect on 638 clutches during the start?
wow, amazing work!
Thanks Mate.
Danke shöne,super videos,for good mood,thank You,So Much👍
Fantastic work... and stay driving it like u stole it... 😉👍👍👍👍👍👍👍👍
Kus umění, nádherný sleeper!
Thank you, nice comment.
mit sinn und verstand sehr schöne arbeit... respekt
Schön, dass die Vorstellung gefallen hat. Vielen Dank für die Rückmeldung.
Awesome...thank you
Thanks Richard. And the clutch still works perfectly.
.. sounds like a Ducati clutch.. YOU ARE A BIG MASTER 😄😄
Thank you, Sir. 😎🤟🏼👍🏻
i really like your hardwork sir. very detail 😍😍😍
Thanks. Every good engineer will confirm, details are important in all technical fields.
@@Quiet.Light.Engineering yes i confirm too. keep your hardwork sir.
Vorneweg: spitzenmäßige Arbeit! Junge war die "alte" Kupplung ausgefeuert 😱. Hätte nicht gedacht das das Drehmoment da so einen Schaden verursacht. Wieviel hatte denn die vorherige Kupplung gelaufen? Freue mich riesig auf die Auspuffanlage! Mach weiter so 👍!
Die alte Kupplung hat knappe 2000 km gehalten und war neu…
@@Quiet.Light.Engineering Ja dachte ich mir schon das die neu war....Wirklich heftig für 2000 Kilometer! Hab vorhin noch die Bilder von den Essen gesehen...🤩...geil!
Как всегда сто лайков тебе !!! Красавчик!!!
Cпасибо александр
Просто и гениально
Спасибо за видео!
Я неделю перед сном задумывал так сделать!
А теперь ещё и увидел что это реально!
Вопрос: какая марка стали на корзину?
42CrMo4.
POWER :D
Nice work. How was the clutch bearing. Thought you might of replaced it to.
There is no clutch bearing. Just simple studs. The mains shaft bearing was good.
Wow
I had a 1974 CZ enduro bike, It had a dry clutch but the shaft seal always leaked so it was a wet clutch.
😂😂👊🏼👍🏻
what material did you use for the clutch basket?
Hi. As shown in the video: 42CrMo4. Can be nitrated without much distortion should it be required.
Hey, since you've machined a new clutch, didn't you consider replacing the sleeve bearing with a needle bearing?
Will you make a video about the exhaust?
Yes, but that takes a while. Still not back from chrome plating and a lot of video material to put together…
@@Quiet.Light.Engineering awesome, can't wait!
I just pee myself a little. Very nice!
Very good... You changed jawa from stock to strong jawa.. so. Are you still working on this project... ??
Yes, a bit. Racing exhaust system next. Coming up soon…
Tenho 8. Motor JAWA 150cc. 3. 250 vc
Hi
Hi I was thinking about making external clutch basket. My idea was to make external basket diameter 4mm bigger and slots for lamels make by EDM wire cutting machine. It would be very strong, easy to production if you have accest to EDM wire cuttin machine.
Why not. Give it a trial. Good luck.
When will you finish this project???
Such projects are probably never finished, mate.
Hi , can you do this clutch for me? What will be the price?
5:43 is just machining porn! Beautiful craftmanship!
Kako da bodem u kotak sa ovg majstora
That’s easy: QuietLightEngineering@gmail.com
Добрый день, возможно ли заказать у вас такую же корзину?
Здравствуйте, в какую страну должен быть отправлен компонент?
And the gearbox was the weak point on Jawa 350. I suppose we see next episode on that soon
Your are right. Already working on improved gears from a rare 575 gearbox..
♦️♦️♦️♦️♦️
Bu motor bloğunun aynısını Türkiye’ye gönder bana
Отправь мне такую корзинку на мою 559/250💜
Bore out your jawa cylinders to 60mm and it's a 367cc bike.
If it was a twin. It‘s not mate…