Thank you very much. Counterclockwise cutting blade is the correct cutting direction of the machine. The blade is tightened even more when cutting in a counterclockwise direction.
I see your point. Miter saw usually spin downward or front to back to avoid saw dust shooting at your face. This saw has dust shooting forward. Anyway, nice job!
@@kietvo1992 You are a knowledgeable person, what you say is correct. But the screw holding the blade is tightened in the right direction. If you turn the blade in the right direction, the blade will fall out, which is very dangerous.
It's not the best idea to use PVC because a high RPM engine will produce high heat which will make the PVC material melt. But your creativity deserves appreciation 🎉
No início vi o símbolo dos lanterna Verde, no meio vi uma arma dos lanterna Verde para o pulso e no final a ferramenta mais fantástica do mundo e totalmente artesanal e funcional.
Run the motor and blade in the opposite direction, you'll have more control over the cut and it Will stop the blade jumping around. Change the screw/nut holding it on to a left hand thread and the blade won't come off. It's not the safest way go use it with the set up you have.
wow, das ist mal ein Gruselvideo. Handwerkliches Geschick ist hast du auf jeden Fall, aber aus PVC eine Werkzeugmaschine herzustellen, die es an Sicherheit, Kraft, Stabilität und Präzision vermissen lässt, halte ich einfach nur für gefährlich. Ich wünsche dir, dass nichts von dem, was da passieren kann, passiert.
Thank you for your interest. The screw holding the saw blade is moved in the forward direction, so the saw blade must rotate in the reverse direction, the saw blade will be tightened when sawing.
PVC sheets? Pure genius to create easy pieces! 😍
Thank you very much
Exelente Video Podrias Mostrar Como Hicistes La Sierra Muchas Gracias !!!!!
This is MASTERPIECE !!!!
Thank you for your ingenuity.
🎉🎉🎉 Video tuyệt vời.
Congratulations on a nice video. I think the motor is reversing and the blade direction is reversed.
Thank you very much. Counterclockwise cutting blade is the correct cutting direction of the machine. The blade is tightened even more when cutting in a counterclockwise direction.
I see your point. Miter saw usually spin downward or front to back to avoid saw dust shooting at your face. This saw has dust shooting forward. Anyway, nice job!
@@kietvo1992 You are a knowledgeable person, what you say is correct. But the screw holding the blade is tightened in the right direction. If you turn the blade in the right direction, the blade will fall out, which is very dangerous.
I like this video it's amazing thank you for bringing it 💜 to view I wish your channel more success
Thank you very much
Gracias por tus fantásticos inventos llenos de creación!
Thank you for your attention
Perfect 👏👏👏🇧🇷🇧🇷🇧🇷
Thank you for creating a creative masterpiece
Thank you for watching the video
Amazing skills brother 😍🎉❤
Thank you
It's not the best idea to use PVC because a high RPM engine will produce high heat which will make the PVC material melt. But your creativity deserves appreciation 🎉
Thank you very much
With proper bearings, PVC can make a lot of useful prototypes.
Thank you for comment
good job bro,,i like it
Thank you very much
Einfach genial , ein bisschen harkt er noch , das darf er aber !
No início vi o símbolo dos lanterna Verde, no meio vi uma arma dos lanterna Verde para o pulso e no final a ferramenta mais fantástica do mundo e totalmente artesanal e funcional.
PARABÉNS VC E O CARA 👋👋👍
Obrigado
Genial invento.
Gracias
❤
süper.
Thanh lý lại đi bạn... 😊😊
Fivou lindo demais 😳
Obrigado
Hola, yo le pondría un guarda al disco y un tope de profundidad.Aun así está muy chula.
Thank you for your attention, your opinion is very reasonable.
what adhesive do you use for gluing the plastic?
I use 502 glue
@@QuangMinh_Selfconstruct Thank you!
Run the motor and blade in the opposite direction, you'll have more control over the cut and it Will stop the blade jumping around.
Change the screw/nut holding it on to a left hand thread and the blade won't come off.
It's not the safest way go use it with the set up you have.
Thank you for your feedback, I was going to do as you said but I couldn't find the screw/thread on the left so I had to do it that way.
sentido da rotação ta errado, e a serra ta virada dai kkkk
Acha pra comprar?
How to make mini table saw
Que medidas usarán en el dispositivo y materiales ?
Please tell me which circular saw cutter you have used in this video
I use the HSS 110mm ultra - thin cutting wheel
Is there a drawing of this wonderful machine?
I don't have the drawings
Por quanto você vende esse aparelho me chamo adilson aguardo a resposta.
Obrigado pela sua atenção. Estou usando este cortador multiangular, então não posso vendê-lo.
пильный диск переверни
Are there any build plans or parts list?
Thank you for your attention
Có file k a
Không có rùi bạn.
Hola, me gustaría tener los planos de la máquina para saber qué medidas usar
No tengo diagrama de la maquina. Pero las medidas y tallas ya están en el vídeo.
@@QuangMinh_Selfconstruct podrías especificar que materiales que sé usaron
wow, das ist mal ein Gruselvideo. Handwerkliches Geschick ist hast du auf jeden Fall, aber aus PVC eine Werkzeugmaschine herzustellen, die es an Sicherheit, Kraft, Stabilität und Präzision vermissen lässt, halte ich einfach nur für gefährlich. Ich wünsche dir, dass nichts von dem, was da passieren kann, passiert.
Vielen Dank
How much cost of this making in materials?
The cost of all the materials is about $20
Can you sell me one?
Thank you for your attention. I don't sell it
the direction of rotation is wrong, this is dangerous and not good
Thank you for your interest. The screw holding the saw blade is moved in the forward direction, so the saw blade must rotate in the reverse direction, the saw blade will be tightened when sawing.
Вопрос. Зачем???😅
To do light manual work.
Для моделистов такие инструменты 😉
Or you can upload STL files to the machine