Installing a Mopar Speedmaster Aluminum Intake Manifold | Mopar 5.9 Magnum Build #17
Vložit
- čas přidán 11. 09. 2024
- The daily-driver 5.9 Magnum going into my truck is going to be carbureted - at least to start with - so I needed a manifold to replace the factory EFI manifold. There aren't a lot of options for the Mopar Magnum engines, and since I'm trying to keep this build lower-cost I decided to try out the Speedmaster mid-rise intake. In this video we'll take a look at the intake as well as the general steps for installing an intake, no matter which one you choose.
Parts used:
Intake: www.summitraci...
Ultra Black RTV: amzn.to/3cN1rOV
MS953921 gasket set: www.summitraci...
Thank you for the build guide. Your vids are to the point. Some other guy has over 17 "steps" but every video is 20 minutes of him unboxing the parts. Thats it. So thanks for doing actual engine work.
Also I believe those round dimples on the lower part of the intake manifold is where you can drill and weld mpi port for fuel injectors
Have you ran this motor yet? I watched this whole playlist multiple times to help me with my complete rebuild. Would love to see yours running if you have a video.
Excellent informative video, very well done.
Looks like the EXACT same casting as the Pro Products Crosswind intake in my vids, except they have their logo in the casting , nice to see a vid on it for magnum I had it on LA Thanks for the vid
Got mine for $135 last black Friday. Let's see if they have any in stock this year. 😂
the bolt holes are ovaled? that means that the gasket head and intake must be aligned perfectly
So there's no video completed and running? Ive got this same intake manifold. Didnt work out. Took 2 gasket sets to get coolant sealed up. Then after trying 3 or 4 different carbs trying to adjust it, i found that it would run with carburator blocked off. There is a major vacuum leak somewhere in #6 or #8 runner. Curious how yours turned out.
Have you ran it yet? How do you like it?
Asking a lot from something a little more than the 1/3rd the price of the Hughes stuff . May use one with a throttle body injection setup on top that’s sold , it ooks like an old Demon carburetor.
How does it perform ?
I know if you do a little work on a Kegger it acts just like a tunnel Ram or a LS style manifold. Considering it was designed for all torque for a truck it couldn’t be worse than a stick Kegger
Are there any intake upgrades for the 5.9 Durango?
Hello, when using this on magnum 5.9. what carb did you use and how did you wire it? What else would I need to swap out kag ND fuel injection for the carb set up. Thanks for video. I just subscribed.
I used an Edelbrock 1406. The only wiring needed is switched power for the choke. That said, if you're replacing injection, I don't have any idea what the ECU will think, what the dash will end up doing or if it will affect the way the transmission shifts.
If anyone comes across this looking for info; you need an LA distributor. The magnum “distributor” isn’t actually a distributor, it’s to synch the fuel injection.
Great point!
Heat the area and freeze the plugs.
Mine are already in, but this is a good idea worth trying for anyone else starting on this.
Jus watched full video 👍 are you using a carburetor instead the factory efi tb ? Is there one for factory efi tb ?
Yes, I'm using a carb and will likely move toa a Holley injection setup. If you want to keep the factory EFI, the factory manifold is the only option I know of.
@@YoshimoshiGarage ok thanks .. I will continue to follow along with your channel now 👍
I bought one and it was the worst china casting I have ever had. I literally put my finger around one runner turn and cut myself and on the top one was hole big enough to put my finger tip in. I spent a couple hours debuting and epoxying
This intake a Summit Chinese knockoff of a Edelbrock 7577? How did the engine run once done?
Yes, I think it's a poor quality casting of a knockoff.
Never actually showed how to install the middle plugs properly. Would you recommend this intake?
I shaved them on the lathe. Someone else suggested freezing them and maybe heating the manifold . Probably worth a try. If I were to do it again, hard to say. The Edelbrock is a lot nicer fit and finish, but it's a lot more expensive, too. For a daily driver, I'd say it's good enough.
What thermostat did you use and neck the stock magnum thermostat is too small
I used the water neck and thermostat from an LA motor
Hello how are you, very good video!
Ask, can you tell me what intake bolts you put in?
I just reused the original bolts from the factory intake.
I would've drilled n tapped and used pipe plugs
That's a pretty good idea, and would look pretty good, too.
What thermostat housing did you use?
Just a standard one off of Rock Auto
Can you get away with not plugging the unused holes?
I think so - they don't seem to open holes to anything. They'll just collect dirt and oil quickly.
@@YoshimoshiGarage ok thanks I'm considering this intake for my build but don't have a press or anything to shave them down
Do them from the bottom
What made you go with that intake?
Mostly price. There aren't many options for the Magnum engines, and since I'm using the factory cam, I wanted a dual plenum and that puts me at either this one or the Edelbrock. They don't look functionally much different and this one was quite a bit cheaper (and you can see why). Should work fine, just not quite as "finished" looking.
@@YoshimoshiGarage smart!
I’m currently doing the kegger mod with mine. Should increase the efficiency and fix the notoriously leaking plenum gasket.
Great vid! Can’t wait to hear it running
because the edlebrock version is 400+ dollars, and this one is like 230$....but now i see why...jesus it sucks...now im not even sure i want to buy it OR the edlebrock one...i guess itll be good enough for a street engine.
@@frigglebiscuit7484 Or you can try and hunt down a Mopar M1 Magnum intake which goes for around $600 used its damn near gold or there is the Hughes Air Gap for those who still want to run the Factory Efi
Um standard c clamp
Waste of 11 minutes
Did you run ac? My ac compressor wont fit with this intake.
No A/C , no.