@tornerong kamay vlog 1) Lapping the head is completely useless , but it is critical that the radius of the cradle be slightly higher than the corresponding radius of the valve-plate. (Think about rotation a 30.000 mm shaft into a 30.000 hole mm. it won't work, you need some play between the hole and the shaft) 2) If you have remove 2.00 mm of material on the cradle of the head ( at the deepest position of the valve-plate), you must also remove exactly 2.00 mm on all the contour of the head. 3) the most important, the cradle MUST be hardened by gas nitrification process only (molten salt don't go deep enough). Without hardening, the pump won't last more than 100 hours while it's design for 10000.
Hello sir actually I only remove 0.004 or less it depends upon the wornout.Its not a hardened its cast iron material,I used only a high speed cutter to cut that one.And actually is not a useless after we repair they used it and they earn more money before they buy a new one.thank you so much for sharing your knowhow too and I appreciate it goodluck
@@tornerongkamayvlog1009 When they are new, the thickness of the hardened metal on a typical cast iron head is 0.005" (Nitrified). If you remove 0.004" there is not much hard surface remaining. And the valve plate is very hard material, pretty sharp at the edge, so it have the bad tendency to "bite" into the softer metal of the cradle. That's why you need to have hardening surface treatment. And when I say lapping is useless, it's because it won't make the pump leak more or less. Assuming that you know how to surface grind the valve plate exactly with the corresponding cylinder block. I must admit that this part is a bit tricky even for seasoned machinist.
@@PopeBenedictXVIHollyman hi ! Why do you wrote « lapping won’t make Leak more or less » ? Do you think it’s necessary to lap together a brand new cylinder when mating it with the old but nice valve plate ? Do you also think it’s best to lap using paper instead of paste ? Thank you for your help !😊
@@renesolaire8319 Why « lapping won’t make Leak more or less » ? Answer; Because I have test it !!! For this particular brand of variable displacement pistons pump from Hitachi, internal leak (or case drain), measured at the drain plug is a steady 4% of the output flow at maximum operational pressure (around 4500 psi), no matter how well lapped or not lapped at all, the valve-plate and the head are matched (new). If the head/valve plate are regrind, the radius of the valve-plate MUST be somewhat smaller. Think as if the valve-plate was a full big shaft inside a corresponding cavity (the cradle of the head). To avoid seizing, the shaft MUST be smaller than the hole. Let's say 19.980" diameter shaft inside a 20.000" hole. Otherwise, the 2 edges of the valve-plate (which is made of hardened steel) are going to "bite" the inside of the cradle on the head and kill the pump after a few hundred of hours only.
Hello host full watch with harang TAMA PO TALAGA ANG CHANNEL NINYO TURNERONG KAMAY KASI NAPAKA GALING PO NINYO SA PANGANGALIKOT NG MGA BAKAL. INGAT PO PALAGE.
@tornerong kamay vlog
1) Lapping the head is completely useless , but it is critical that the radius of the cradle be slightly higher than the corresponding radius of the valve-plate. (Think about rotation a 30.000 mm shaft into a 30.000 hole mm. it won't work, you need some play between the hole and the shaft)
2) If you have remove 2.00 mm of material on the cradle of the head ( at the deepest position of the valve-plate), you must also remove exactly 2.00 mm on all the contour of the head.
3) the most important, the cradle MUST be hardened by gas nitrification process only (molten salt don't go deep enough). Without hardening, the pump won't last more than 100 hours while it's design for 10000.
Hello sir actually I only remove 0.004 or less it depends upon the wornout.Its not a hardened its cast iron material,I used only a high speed cutter to cut that one.And actually is not a useless after we repair they used it and they earn more money before they buy a new one.thank you so much for sharing your knowhow too and I appreciate it goodluck
@@tornerongkamayvlog1009 When they are new, the thickness of the hardened metal on a typical cast iron head is 0.005" (Nitrified). If you remove 0.004" there is not much hard surface remaining. And the valve plate is very hard material, pretty sharp at the edge, so it have the bad tendency to "bite" into the softer metal of the cradle. That's why you need to have hardening surface treatment.
And when I say lapping is useless, it's because it won't make the pump leak more or less. Assuming that you know how to surface grind the valve plate exactly with the corresponding cylinder block. I must admit that this part is a bit tricky even for seasoned machinist.
What is the name of the oil?
@@PopeBenedictXVIHollyman hi ! Why do you wrote « lapping won’t make Leak more or less » ? Do you think it’s necessary to lap together a brand new cylinder when mating it with the old but nice valve plate ? Do you also think it’s best to lap using paper instead of paste ? Thank you for your help !😊
@@renesolaire8319 Why « lapping won’t make Leak more or less » ?
Answer; Because I have test it !!!
For this particular brand of variable displacement pistons pump from Hitachi, internal leak (or case drain), measured at the drain plug is a steady 4% of the output flow at maximum operational pressure (around 4500 psi), no matter how well lapped or not lapped at all, the valve-plate and the head are matched (new). If the head/valve plate are regrind, the radius of the valve-plate MUST be somewhat smaller. Think as if the valve-plate was a full big shaft inside a corresponding cavity (the cradle of the head). To avoid seizing, the shaft MUST be smaller than the hole. Let's say 19.980" diameter shaft inside a 20.000" hole. Otherwise, the 2 edges of the valve-plate (which is made of hardened steel) are going to "bite" the inside of the cradle on the head and kill the pump after a few hundred of hours only.
Grand Master, as your follower and colleague from Turkey, I respectfully salute you 🙏
Tamsak watching live
Thank you bro
replay host w/paharang fullwatch...
Thank you so much maam goodluck to you
Watching replay po
Thank you so much maam goodluck to you
Watching premier host
Yes maam nkita kita doon maraming salamat
Hello host full watch with harang TAMA PO TALAGA ANG CHANNEL NINYO TURNERONG KAMAY KASI NAPAKA GALING PO NINYO SA PANGANGALIKOT NG MGA BAKAL. INGAT PO PALAGE.
Hehe maraming salamat maam tama amping din kayo palage
Tamsak host watch full replay po..ingat ho kayu lage sa work dipo biro amg trabho nyu thumbs up po 😊
Salamat kaayo mega goodluck diha
waiitng here ulit...
Thank you so much maam
Waiting premier.
Thank you so much maam
Watching your premier live melabs to show my appreciation and support
Yes maam nakita kita doon maraming salamat sa support palage GOD BLESS
waiting na ito bro
Thank you so much bro
nice video chong....watching and support share.my friend
Thank you so much chong goodluck to you
Watching sir #tornerongKamayvlog
Tamslove my kuya tor..waiting n here
Thank you so much maam ingat always
L96 fullwatch done na ito bro. like refracing hydraulic pump head cover with niew cylinder block and valve plate. here to support. god bless
Thank you so much GOD BLESS YOU TOO
waiting prem host
Thank you maam
Watching your premier bai. Natimingan rin. 👍
Yes bai nakita kita doon maraming salamat hehe timing timing lang yan goodluck bai
tamslAb wAtching live po
Yes maam nakita kita doon thank you so much
Hello fren watching live your video keepsafe always
Yes fren nkita kita doon maraming salamat keepaafe always too
Sending my full support kabayan maganda ito informative video makakatulong ito kabayan salamat
Maraming salamat kabayan goodluck to you
ang galing mag ayos ah
Salamat ma'am MB goodluck
like 2 tamblab host good luck
Thank you so much love goodluck to you too
Tamsak host watching replay done
Thank you so much maam
Waiting host
Thank you idol
Waiting for this premiere first like
Maam thank you so much more blessings and GOD BLESS
Good job bai partner ingat
Thank you so much ingat din kayo dyan GOS BLESS
Watching here from Oton 🌅🌅🌅
Thank you so much bro keepsafe always
Galing! Ingat kau lagi sa work nyo sir
Maraming salamat maam ingat din kayo palage
Ang husay mo tlga kaibigan.
Maraming salamat kaibigan goodluck sa trabaho
Watching refacing hydrolic pump with ads
Thank you so much bro ingat sa work
looking forward for this premiere mo Bai
Thank you so much bai
You’re good, thanks for sharing us what you do with refacing hydraulic pump and such.
Thank you so much maam goodluck
Waitting here
Thank you day
Likes 77 watching live Bai
Yes bai nkita kita doon maraming salamat bai
Sending hug and support kabayan
Thank you idol
Thanks host
Welcome sir thank you din goodluck
tambzlab host
Thank you maam
Lk dn pre watched
Thank you so much my friend
ang galing...
Thank you so much mega
Tmslab waiting
Maam thank you sa support ingat palage
Nice vedio 💝💝 my friend
Thank you so much my friend
Lablam ma'am tornero tusok
Thank you sir mag binuotan palage hehe
Hello hoots nice share video 👍👍👍
Hi kawan thank you so much
watching and sending support Connected to your channel
Yes sir nakita kita doon maraming salamat GOD BLESS
Waiting ❤️
Thank you so much maam keepsafe
Done full replay mego
Thank you so much maam eve
Shout out sir
Sir san ung shop nyo
Sending my support
Thank you so much maam blessed sunday
Waiting
Thank you maam
Tamsak💕✅✅✅✅
Thank you so much maam
Waiting sir
Maam lhyn thank you ingat palage
like 31 ltambzlab host
Thank you so much maam love
Waiting sir tornero
Thank you so much maam lhyn ha sa support palage ingat maam sa work
Yahooo
Thank you amiga yahooooo
Wait for this L18
Thank you so much maam
I'm here tornerzzzzz
Thank you bajjzz
هناك طريقه افضل
Location po
Malaysia po lods
Repacing hydraulic
Thank you so much sir
Zaxis 225
L27
Thank you
Hello po, new subscriber here, padikit po sa kubo namin Godbless
Tamsak watching replay po
Waiting
Thank you so much bro