Hello could you please tell me where connector Chestnut than you have tested number 20 goes because I don't have 12V on the radio or the center console. for information all fuses ok optics is ok
Hi, I test the system with optical loop cable. I tried connecting different. Systems installed at in the boot (Sat Nav, sound amp, etc) and under dash with female plug in loop cable, but still RMC MMI unit didn’t turn on. I tied to put male optical loop cable in RMC control unit, to see if the systems cones in, but still no luck. But I narrowed down the issue to RMC control unit, I think the circuit board is faulty. Any help , how to replace or repair the RMC MMI board on Audi A1 2012? Thanks.,
I have a a5 sometimes it boots up most of the time not but can still enter a CD and eject no mmi sat nav or steering wheel controls if u try turn on u can hear it trying to boot up
The Audi a6 c6 central panel half the keys work half it doesn't work and doesn't light up. The steering commands don't work at all and the lights, what could be a malfunction? And is the central panel of the mmi connected to the steering wheel?
Can anyone tell me how to install a aftermarket radio in a q7 sline quattro 09 TDI i have the fibers optics to the unit 10.1" and can't get the power to the unit i just want to no how the power go to the unit that is all it is 3 wire that comes out of the q7 i can't find adapter to go to my unit 1 of the wire is brown one is green with white the next one is yellow i no that it is the power i don't no if the green is the ground wire and the Brown is the key can anyone help out please i want to use this unit in the q7
Great work, and a nice find. When you replaced the board on the other car you spoke of, did you have to reprogram it or can it be replaced with a secondhand unit?
Nice video... my cars mmi display is fine but cd paused itself and no sounds from mmi. I checked the amp with fibre optic loop still same. Please could you give me some suggestions
thank you so much for this video i have little question about mmi that bought it . i think this is protected by component protection. did you off cp for mmi or not
Hi Have not been through that yet... czcams.com/video/5Jl_poF35_A/video.html Expose you question on the forum... someone might be able to help you... Thank you for watching!
The problem others have experienced with Autel scan tools is if the computer is not responding, the Autel skips it. Unlike OTC which will list the system with a no communication error.
H is my centre button doesn’t work when I scroll few lights are off I want to replace the board but do I need a 2g or 3g board ? It’s 2008 il has the navigation and a can conect my phone for calls
Hi mate I've got a 2012 a6 and my mmi works fine but after 10 secs it switches off n the lights on the buttons stay it's like it get initial power n then looses it?
Hi scan the car first... systems nowadays are quite smart, and they log faults... See if there is anything that guides you in the right direction... Thank you for watching!
The dude just dismantled the whole car like hell no I’m not attempting to do any of that. As an ordinary person with basic understanding of things, I thought the video would show an easy solution like pushing a hard reset button hidden somewhere in the car. Now a visit to the mechanic is inevitable lol
@@LMAutoRepairs You're welcome. I wanna thank you as well. Very insightful video. I have the same problem with my 2010 Q7. I read somewhere that if you press Setup + the cursor and the top right arrow at the same time, the MMI would reset. Is that true? I tried it but it didn't work. You're probably right though. My wife (not me of course) probably spilled something there though there's no way she'll ever admit that lol
Hi mate, good video. I have an Audi A6 C6 that has a similar MMI controller but the one with 4 buttons only. The screen works fine and it responds to some steering wheel controls but the controller in the middle console doesn’t work at all! I have tried to clean with alcohol as well but no success. Should have at least lighten up but is dead. Do you think there is a blown fuse as well?
Possibly... but check power and grounds at the controller plug... if all there, then you have a bad controller... Thank you for watching and for your comment!
As always, well done! As plus information, in Gateway you have some blocks that indicates the communication in differents networks: confort, powertrain, Most, etc.. They are from 120 to 130, depending of the equipment
Hi and thanks for your video. I did (change mmi) everything like you explained but the radio still doing the same thing. I'm suspicious to fuse. Could you please help me found where the radio fuse are located please? Thanks and God bless you.
J.A.C.P I have a quick question? Where is that amplifier located? Do you have a part number? I have a 2007 Q7 Can you post a picture of it? I already changed the MMI card and I have power on the line that plugs into the MMI card so my best guess is the amplifier may be the problem. Thanks in advance looking forward to hearing from you!!
Hi! I have the same problem and after to install the new board everything works fine, except te center selector cylinder. You don’t have these problem?
You might have a different model... Check all fuses on the car... specially the ones on the interior fuse boxes... other than that, you might need diagrams...
Any idea about 2009 mmi screen and control button lights on centre console not working? I had water in both compartments in the boot from the roof, all fuses seem to be okay. Cheers
Hi, nice videos. Wondering , what’s your location? I wanted to bring in car for repairs if you near by. Control unit & display screen stopped working suddenly. Though head unit still takes in cd/DVD & ejects etc. I need help to sort out this issue, Plzz
Hi, I test the system with optical loop cable. I tried connecting different. Systems installed at in the boot (Sat Nav, sound amp, etc) and under dash with female plug in loop cable, but still RMC MMI unit didn’t turn on. I tied to put male optical loop cable in RMC control unit, to see if the systems cones in, but still no luck. But I narrowed down the issue to RMC control unit, I think the circuit board is faulty. Any help , how to replace or repair the RMC MMI board on Audi A1 2012? Thanks.,
i have the same problem but when i press combination of 3 buttons for reset everything turn on display and radio are working fine then when i turn off my car after minute car goes to sleep i put key in start the car radio and display is dead again when i press that combination of 3 buttons again it start again everything is working ???? did you ever had that case ?
Hi Isopropyl Alcohol rover.ebay.com/rover/1/710-53481-19255-0/1?mpre=https%3A%2F%2Fwww.ebay.co.uk%2Fitm%2FIPA-99-9-1-LITRE-Lab-Grade-Isopropyl-Alcohol-Isopropanol-1L%2F183965887641%3Fhash%3Ditem2ad538ac99%3Ag%3AYNMAAOSw3FNdh1yc&campid=5338344466&toolid=20008 Thank you for watching!
Hi. Great vid. I have an A6 C6. Battery died and the local mechanic tried jump starting it through the battery rather than at the points under the bonnet. He eventually got it going but MMI hasn’t worked since. It starts for a second but then shuts down. I replaced the control unit, checked all fuses, replaced the amplifier in the boot and checked the radio unit in the glove compartment. Still same problem. Any suggestions?
@@LMAutoRepairs Yes. My Polish mechanic scanned it and said that it was the fibre optic system was showing a fault and it was most likely a component in the amplifier in the boot. Mine is a Harman Becker automotive system. I replaced it and still have the same issue. He also suggest it might be the cable got damaged but it was working fine before the battery went dead. ???
The most bus can be diagnosed using fibre optic loops, and if it is a cable, you can also easily diagnose it by checking the loops... I also doubt that the jump starting would damage a cable... Yo7 need to check all the modules in the most bus... one by one... And one thing... avoid to jump start cars with loads of electronics... that is what happens... 👍👍👍
I have 2008 a6 4.2 Having the same issue no power at all the whole system is down But mine have cd changer in the glove box How i can know where the power coming to it I apriciate if you can help
No i replacet the board but still nothing power up 1-I check the 3 fuse boxes 2-i tried to baypass the fiber optic loop for every simgle unit 3-i took the module behind glove box open it its look clean but no red wire that coming to it no power some other wires have power Im trying to find where this module take power i cant all the fuses good and no fuses missing
Hi mate, I've had a problem with a fuzzy display. There's no problems with power etc, just the actual display screen is different colours and lines, sometimes it would return as normal, but is now constant, I'm suspecting water damage as the drain in engine bay was blocked up and footwells became flooded. Do you have any advice how to fix this, thanks. Great video
Hi If you suffered from water intrusion, there is no silver bullets... Start by inspect and clean if necessary all the connectors, etc... see where the water went to and clean... 👍👍👍
@@LMAutoRepairs Thanks for reply, do you know if there is a connector linked to mmi, under carpet in drivers footwell. I seem to recall this, that would maybe explain problem
thank you for the video. i have an audi A6 2006 MODEL and the mmi screen doesn't light up but the controls are working and the radio is working only the screen. any ideas?
Thanks. i replaced this with new board, some seconds all the red led on board and MMI LCD show up then gone. no any button actions too. what is your suggestion?
That's a stupid place to put the fuse which powers the Cd player, the controller and the MMI. It should be with all the other fuses in a fuse box. This forces you to pull out the cd player which created a bigger headache
WELCOME TO THE MOST BUS WORLD.....TRY DEALING WITH IT ALMOST DAILY.....I ALWAYS END UP REPLACING THE 07 MODULE...BUT I AM CURIOUS TO SEE HOW U COME OVER COMPONENT PROTECTION THAT IS ACTIVE THE MINUTE U REPLACE A COMPONENT OF THE MOST BUS CIRCUIT......LET ME KNOW..
@@LMAutoRepairs U ARE SURE CORRECT...NOT AN EASY FREAKING JOB.....15 MIN TO REPLACE AND 50 MIN TO PROGRAMM THIS SHIT.............I WAS CURIOUS WHERE U PICKED UP THE BOARD...LET ME KNOW IF U ARE OK WITH IT...
@@LMAutoRepairs cool, i was using soap and water on just the buttons. They were working then the next day after i but it back together the inner buttons are sticking again. Will tear it back apart and reclean the buttons again. Not the buttons on the electrical board, the buttons on the main piece that you push when its in the car i ment
Meron akong inaayos na audi a8 2011 model loss com ang mmi pero kumpleto naman ang supply nag check na ako ng fiber optic ok naman .. pagkinabit ko sa iba ang mmi module gumagana.. ano pa kayang pweding posible na sira at dapat i check..
@@tenekahall1617 I fixed it last year, here is the video. It is in my polish language, but you can see the problem (back door water going into BOSE unit). czcams.com/video/kExQbtQcUCk/video.html
Gd spilled soda and didnt tell me... Wow.. Media doesnt start... Rsdio works blue tooth for phone callworks..but i cant play.my youtubemusic into the car... F soda is shit.
Thanx Louis, it always a pleasure watching your videos !!
Thanks Colin!
👍👍👍
Nice one mate, always a wow when watching your videos keep it up.
Hi
Thank you for watching and for your comment!
👍👍👍
What is number 18 for does that heat the car up before you go into it the auxiliary parking heating
Hello
could you please tell me where connector Chestnut than you have tested number 20 goes because I don't have 12V on the radio or the center console.
for information all
fuses ok
optics is ok
Great work Luis
Thanks!
Hi, I test the system with optical loop cable. I tried connecting different. Systems installed at in the boot (Sat Nav, sound amp, etc) and under dash with female plug in loop cable, but still RMC MMI unit didn’t turn on.
I tied to put male optical loop cable in RMC control unit, to see if the systems cones in, but still no luck. But I narrowed down the issue to RMC control unit, I think the circuit board is faulty. Any help , how to replace or repair the RMC MMI board on Audi A1 2012? Thanks.,
Awesome work/video! Thank you many times over!
😊
👍👍👍
I have the same issue with my 2008 Q7, are you able to sort it for me please?
Nice work man 👏👏
Thanks!
👍👍👍
Thank you for another great video
Thanks!
👍👍👍
Thank you for another great video!!!
Thank you for watching and for your comment!
Hi friend can you explain audi A6 the same problem thank you
Enjoyed this video so much! Keep up the good work!!!
Hi
Thanks!😊
👍👍👍
Wich is the fuse for the mmi?
I have a a5 sometimes it boots up most of the time not but can still enter a CD and eject no mmi sat nav or steering wheel controls if u try turn on u can hear it trying to boot up
great job .... thanks for your information
Thanks!
👍👍👍
Thank you very much this video really help.
😊
Thank you for watching and for your comment!
👍👍👍
The Audi a6 c6 central panel half the keys work half it doesn't work and doesn't light up. The steering commands don't work at all and the lights, what could be a malfunction? And is the central panel of the mmi connected to the steering wheel?
Nice video. Good to see you managed to repair it. I have seen that brown plug in the control unit of the windows in the driver door of my passat. :-)
Lol
Thank you for watching and for your comment!
Can anyone tell me how to install a aftermarket radio in a q7 sline quattro 09 TDI i have the fibers optics to the unit 10.1" and can't get the power to the unit i just want to no how the power go to the unit that is all it is 3 wire that comes out of the q7 i can't find adapter to go to my unit 1 of the wire is brown one is green with white the next one is yellow i no that it is the power i don't no if the green is the ground wire and the Brown is the key can anyone help out please i want to use this unit in the q7
I dont have a fuse on my radio, maybe u know where it can be?
Great work, and a nice find. When you replaced the board on the other car you spoke of, did you have to reprogram it or can it be replaced with a secondhand unit?
No reprogramming required...
👍👍👍
Another great vid as usual mate 👍
Thanks...
👍👍👍
Nice video... my cars mmi display is fine but cd paused itself and no sounds from mmi. I checked the amp with fibre optic loop still same. Please could you give me some suggestions
I would scan the car and go from there...
👍
Thank you for watching!
thank you so much for this video
i have little question about mmi that bought it . i think this is protected by component protection. did you off cp for mmi or not
Hi
Have not been through that yet...
czcams.com/video/5Jl_poF35_A/video.html
Expose you question on the forum... someone might be able to help you...
Thank you for watching!
The problem others have experienced with Autel scan tools is if the computer is not responding, the Autel skips it. Unlike OTC which will list the system with a no communication error.
That's correct... it assumes that the module is not fitted...
Thank you for watching!
H is my centre button doesn’t work when I scroll few lights are off I want to replace the board but do I need a 2g or 3g board ? It’s 2008 il has the navigation and a can conect my phone for calls
you are magician
Lol
I wish...
Thank you for watching and for your comment!
I have no power on the mmi panel near the shift gear nor cigarett lighter. Also my mmi screen comes on with audi emblem and then goes out.
you are a god
😊
Wouldn't take it that far... lol
Thank you for watching and for your comment!
Great video. Do you need to do any reprogramming after you insert the new circuit board?
No...
Thank you for watching!
Useful video 👍
Thanks!
👍👍👍
Hi
Car.Audi Q7 2008 3000 TDI
İ will change odometer
Which path should I follow?
Sade mode
The plastics are very clean
Hi mate I've got a 2012 a6 and my mmi works fine but after 10 secs it switches off n the lights on the buttons stay it's like it get initial power n then looses it?
Hi
scan the car first... systems nowadays are quite smart, and they log faults...
See if there is anything that guides you in the right direction...
Thank you for watching!
Hi i have audi q7 2011 the steering up and down not working what should i do only forward and back working any help thanks
I would start by get it scanned, and look at some live data... see if the issue is the switch or the motor...
Thank you for watching!
Hi thanks for your video. Where can i order the circuit board please. I need one for a 2011 a6
Thanks
I got this one from eBay...
Thank you for watching!
Dear Sir, i have water damage on my amp. At the fibre inlet area. Do you maybe have a BOSE amp schematic for me - Audi Q7.
No I don't... sorry...
The dude just dismantled the whole car like hell no I’m not attempting to do any of that. As an ordinary person with basic understanding of things, I thought the video would show an easy solution like pushing a hard reset button hidden somewhere in the car. Now a visit to the mechanic is inevitable lol
No magic buttons for when you decide to water the electronics of the car...
LoL
Thank you for watching!
@@LMAutoRepairs You're welcome. I wanna thank you as well. Very insightful video. I have the same problem with my 2010 Q7. I read somewhere that if you press Setup + the cursor and the top right arrow at the same time, the MMI would reset. Is that true? I tried it but it didn't work. You're probably right though. My wife (not me of course) probably spilled something there though there's no way she'll ever admit that lol
No worries...
I am sure there is a reset procedure...
All depends on your model...
👍👍👍
There is no fuse behind the radio of my 2009 audi q7.
I have the same problem on my vauxhall insignia 2009
Hi mate, good video. I have an Audi A6 C6 that has a similar MMI controller but the one with 4 buttons only. The screen works fine and it responds to some steering wheel controls but the controller in the middle console doesn’t work at all! I have tried to clean with alcohol as well but no success. Should have at least lighten up but is dead. Do you think there is a blown fuse as well?
Possibly... but check power and grounds at the controller plug... if all there, then you have a bad controller...
Thank you for watching and for your comment!
Hi, I’m having the same problem but with a Audi a1 my radio docent have a fuse on the back of it any advice
same here, did you figure this out?
As always, well done!
As plus information, in Gateway you have some blocks that indicates the communication in differents networks: confort, powertrain, Most, etc..
They are from 120 to 130, depending of the equipment
Thanks!
👍👍👍
Can anyone help me out have a few questions
Hi, where did you get the replacement board and what was the cost ?
Ebay... can't remember now how much it was...
Thank you for watching!
Hi and thanks for your video. I did (change mmi) everything like you explained but the radio still doing the same thing. I'm suspicious to fuse. Could you please help me found where the radio fuse are located please? Thanks and God bless you.
The fuse is behind the unit... on the unit itself...
Thank you watching!
@@LMAutoRepairs Hi I have the same problem with the screen, and my system does not have a fuse behind it.. Mine is a 2007 Audi Q7 UK model.. thanks
@@MsREDCIVIC Change the amplifier in the back, my car had the same problem.
J.A.C.P I have a quick question?
Where is that amplifier located? Do you have a part number? I have a 2007 Q7 Can you post a picture of it? I already changed the MMI card and I have power on the line that plugs into the MMI card so my best guess is the amplifier may be the problem. Thanks in advance looking forward to hearing from you!!
Hi! I have the same problem and after to install the new board everything works fine, except te center selector cylinder. You don’t have these problem?
No...
Check live data... confirm that the button is actually working...
I know is a new board, but you never know...
Thank you for watching!
I have the same problem...but i can't find the fuse behind of radio!!! Where can be??
You might have a different model...
Check all fuses on the car... specially the ones on the interior fuse boxes... other than that, you might need diagrams...
you stuck your lead end into the seat? @3225 lol
Hi I have got Audi Q7 2008 same MMI can we update it to android or Apple car play with a new screen ?
Possibly... never researched such thing...
Thank you for watching!
What did you use to take the radio unit out? Pleaseee I have the same problem
Any idea about 2009 mmi screen and control button lights on centre console not working? I had water in both compartments in the boot from the roof, all fuses seem to be okay. Cheers
Check the areas where the water has been... check for corrosion etc...
👍👍👍
@@LMAutoRepairs I've dried out everything, checked fuses again but unfortunately no luck.
Grear stuff
Thanks!
👍👍👍
Thanks for the video. Where did you get your PCB board to purchase ? I have the same issue with my 2009 Q7 MMI not working, Thanks for your help
From eBay at the time, if recall correctly...
👍👍👍
Hi name is darcy I have audi A6 2006 my radio is working fine but mmi screen is not working
Hi, nice videos. Wondering , what’s your location? I wanted to bring in car for repairs if you near by. Control unit & display screen stopped working suddenly. Though head unit still takes in cd/DVD & ejects etc. I need help to sort out this issue, Plzz
Hi, I test the system with optical loop cable. I tried connecting different. Systems installed at in the boot (Sat Nav, sound amp, etc) and under dash with female plug in loop cable, but still RMC MMI unit didn’t turn on.
I tied to put male optical loop cable in RMC control unit, to see if the systems cones in, but still no luck. But I narrowed down the issue to RMC control unit, I think the circuit board is faulty. Any help , how to replace or repair the RMC MMI board on Audi A1 2012? Thanks.,
i have the same problem but when i press combination of 3 buttons for reset everything turn on display and radio are working fine then when i turn off my car after minute car goes to sleep i put key in start the car radio and display is dead again when i press that combination of 3 buttons again it start again everything is working ???? did you ever had that case ?
No... never had that...
Hi man im from spain
I like your videos alot
Where can i get de UTEL MAXISYS that you use??
Hi
I bought it from eBay...
Thank you for watching and for your comment!
🎄👍👍🎄🎄👍🎄👍🎄👍🎄👍🎄👍
With what did you clean this syrup, alcohol?
Yes...
Thank you for watching!
what do you clean the circuit board with?
Hi
Isopropyl Alcohol
rover.ebay.com/rover/1/710-53481-19255-0/1?mpre=https%3A%2F%2Fwww.ebay.co.uk%2Fitm%2FIPA-99-9-1-LITRE-Lab-Grade-Isopropyl-Alcohol-Isopropanol-1L%2F183965887641%3Fhash%3Ditem2ad538ac99%3Ag%3AYNMAAOSw3FNdh1yc&campid=5338344466&toolid=20008
Thank you for watching!
What did you use to clean that MMI out
Isopropyl alcohol...
Thank you for watching!
Hi. Great vid. I have an A6 C6. Battery died and the local mechanic tried jump starting it through the battery rather than at the points under the bonnet. He eventually got it going but MMI hasn’t worked since. It starts for a second but then shuts down. I replaced the control unit, checked all fuses, replaced the amplifier in the boot and checked the radio unit in the glove compartment. Still same problem. Any suggestions?
Have you scanned the system?
👍👍👍
@@LMAutoRepairs Yes. My Polish mechanic scanned it and said that it was the fibre optic system was showing a fault and it was most likely a component in the amplifier in the boot. Mine is a Harman Becker automotive system. I replaced it and still have the same issue. He also suggest it might be the cable got damaged but it was working fine before the battery went dead. ???
The most bus can be diagnosed using fibre optic loops, and if it is a cable, you can also easily diagnose it by checking the loops...
I also doubt that the jump starting would damage a cable...
Yo7 need to check all the modules in the most bus... one by one...
And one thing... avoid to jump start cars with loads of electronics... that is what happens...
👍👍👍
I have 2008 a6 4.2
Having the same issue no power at all the whole system is down
But mine have cd changer in the glove box
How i can know where the power coming to it
I apriciate if you can help
Check fuses...
Have you had liquid spilled over it as well?
Thank you for watching!
No i replacet the board but still nothing power up
1-I check the 3 fuse boxes
2-i tried to baypass the fiber optic loop for every simgle unit
3-i took the module behind glove box open it its look clean but no red wire that coming to it no power some other wires have power
Im trying to find where this module take power i cant all the fuses good and no fuses missing
@@elienasr4387 Any luck? Same car same problem. My screen tries to turn on but turns off in seconds every time
I just got a q7 wit similar issue pl help 911
i have the same problem with my audi q7 2008
my stupid mmi 2017 sq7 screen turns off while i'm driving and turning on like crazy
Hi mate, I've had a problem with a fuzzy display. There's no problems with power etc, just the actual display screen is different colours and lines, sometimes it would return as normal, but is now constant, I'm suspecting water damage as the drain in engine bay was blocked up and footwells became flooded. Do you have any advice how to fix this, thanks. Great video
Hi
If you suffered from water intrusion, there is no silver bullets...
Start by inspect and clean if necessary all the connectors, etc... see where the water went to and clean...
👍👍👍
@@LMAutoRepairs Thanks for reply, do you know if there is a connector linked to mmi, under carpet in drivers footwell. I seem to recall this, that would maybe explain problem
what model do you have of your maxisys
Hi
MS908P
Thank you for watching!
Thx 👍👍
👍👍👍
thank you for the video. i have an audi A6 2006 MODEL and the mmi screen doesn't light up but the controls are working and the radio is working only the screen. any ideas?
Hi
Bad screen?
Check power and grounds etc...
Thank you for watching and for your comment!
Do you still have this problem? I think I can help you out
is the fuse behind the cd exchange or the actual radio?
Radio...
Teneka Hall, this May help if you have not solve your problem. czcams.com/video/IWW9QX8SOEA/video.html
Hello Good Morning. Where are you located?
Great job. Where did you purchase the pcb from
Ebay if I recall correctly...
👍👍👍
Thanks. i replaced this with new board, some seconds all the red led on board and MMI LCD show up then gone. no any button actions too. what is your suggestion?
Check powers and grounds grounds...
Thank you for watching!
u fixe it?
Looking for a good diagnostic tool supplier in uk... what shop do you use?
Hi
Depends what you are looking for...
Thank you for watching!
That's a stupid place to put the fuse which powers the Cd player, the controller and the MMI. It should be with all the other fuses in a fuse box. This forces you to pull out the cd player which created a bigger headache
Where do you order your electrical boards from? Great video
Hi
From wherever I find them...
This one, from eBay...
Thank you for watching!
LM Auto Repairs do you know if the Q5 is the same board !? I can’t find one specific to Q5 just q7
They possibly share the same... but i never seen the one from the Q5... so don't take my word for it...
Thank you for watching!
Does the nav still work?
Have not been told otherwise...
Thank you for watching!
👍
Where did you buy the motherboard pleaze?
If I recall correctly, on eBay...
Thank you for watching!
Nice video. Can you share link to purchasing the board, I have same problem in my Q7.
There is loads on eBay...
👍👍👍
@@LMAutoRepairs Yes, saw many listings with different rates, but not sure about the quality
☺️
The one I have used on this video, it is still going...
Keep liquids out of the way and you should be fine...
👍👍👍
@@LMAutoRepairs great. Thanks.
@@LMAutoRepairs Seem the way to go. Thank you.
What program and scan tool are you using
MS908P...
👍👍👍
Thanks for the video.
Q: Where did you buy only the pcb?
Hi
EBay...
Thank you for watching and for your comment!
Wow exactly my first thought :D
Do you clean it with alcohol or soap?
Isopropyl alcohol...
👍👍👍
This will work on Audi a6 c6 2007
WELCOME TO THE MOST BUS WORLD.....TRY DEALING WITH IT ALMOST DAILY.....I ALWAYS END UP REPLACING THE 07 MODULE...BUT I AM CURIOUS TO SEE HOW U COME OVER COMPONENT PROTECTION THAT IS ACTIVE THE MINUTE U REPLACE A COMPONENT OF THE MOST BUS CIRCUIT......LET ME KNOW..
Never had to do one... but heard is not easy...
Thank you for watching!
@@LMAutoRepairs U ARE SURE CORRECT...NOT AN EASY FREAKING JOB.....15 MIN TO REPLACE AND 50 MIN TO PROGRAMM THIS SHIT.............I WAS CURIOUS WHERE U PICKED UP THE BOARD...LET ME KNOW IF U ARE OK WITH IT...
How did you clean the buttons
Isopropyl alcohol...
Thank you for watching!
@@LMAutoRepairs cool, i was using soap and water on just the buttons. They were working then the next day after i but it back together the inner buttons are sticking again. Will tear it back apart and reclean the buttons again. Not the buttons on the electrical board, the buttons on the main piece that you push when its in the car i ment
@@jasonschagt6527
Ah... yes you need something like the alcohol that dissolves the sugar/sticky stuff...
👍👍👍
Prolong spl 500 anticorrosionoil
Meron akong inaayos na audi a8 2011 model loss com ang mmi pero kumpleto naman ang supply nag check na ako ng fiber optic ok naman .. pagkinabit ko sa iba ang mmi module gumagana.. ano pa kayang pweding posible na sira at dapat i check..
I replaced circuit board and nothing please help
Have you checked fuses?
LM Auto Repairs same issue here! Changed circuit board and nothing and checked the fuses
Teylor Ray. This may help if you haven’t solve your problem. czcams.com/video/IWW9QX8SOEA/video.html
problem for me resolved an audi Q5
👍👍
Where are you located
UK
Thank you for watching!
@@LMAutoRepairs whereabouts mate
love the design, obv gonna spill your drink...oh nice place to spill it
Lol...
Thank you for watching!
Do an ultrasonic clean.
Not a bad idea...
👍
Thank you for watching and for your comment!
Save the old board for spare parts, specially the led's
I did...😉
The owner did no wanted the old part...
Thank you for watching!
Good job. Now I go to my wife' Q7 and find the same problem - MMI no screen.
martinflashgordon what was wrong? My car just came from the dealer I replaced the amp but it wasn’t the amp.
@@tenekahall1617 I fixed it last year, here is the video. It is in my polish language, but you can see the problem (back door water going into BOSE unit).
czcams.com/video/kExQbtQcUCk/video.html
The coke cola dried up gooey syrup attacks again 😁. Great job mate 👍👍👍
Lol
Thanks!
👍👍👍
that screen looks old
Next time try to show us any module you are disassembling so that we see if you break anything
What?
🤷♂️
Why don't people tell you they might have spilled some sort of liquid on the radio controls it would save you so much time
Lol
I get that all the time... 🤦♂️
Thank you for watching and for your comment!
Gd spilled soda and didnt tell me... Wow.. Media doesnt start... Rsdio works blue tooth for phone callworks..but i cant play.my youtubemusic into the car... F soda is shit.