Video není dostupné.
Omlouváme se.
How To Clean Carburetor and Impeller Replacement on Mercury 15 (four stroke)
Vložit
- čas přidán 11. 07. 2018
- step-by-step / how-to video on how to clean a carburetor, and replace an impeller on a mercury outboard.
if you have any questions, please feel free to ask in the comment section and I will do my best to answer to the best of my knowledge.
You not only shared your knowledge but also created an easily understood vid. Thanks for making sure we could see what you were doing & explaining everything. Great job.
THANK YOU FOR BEING SO VERY KIND TO SHARE YOUR KNOWLEDGE PLEASE CONTINUE, THANK YOU AND GOD BLESS YOU.
Bro VERY WELL DONE!!! Great Job!! Great way to show people how to do it right!! Hopefully young people can learn from a video like this… Well Done Sir!
Awesome video. I have a 20 HP tohatsu exact same motor was unsure about taking apart the carb. Seems like a piece of cake. Thanks for the informational video.
Thank you for sharing. What a great video. Thank you!
thank you for this!!!!!!!!!!!
Awesome video my friend! Very useful and very good explained.
Very good video you make it look so easy thank you.
Excellent tutorial my friend Thank you
Thanks for the detailed video. I have the exact motor and it only ran when choked fully. Crap in the jets of course!
Good video thanks
Excellent video. 2 notes for you. Silicone grease should be used on impellers not petroleum grease. Pet grease will break down the rubber over time. Ever use Creolina undiluted to polish up your brass carb parts? No sand paper needed. Amazing stuff. Americans never heard of it.. it is in many latin supermarkets. It takes a few hours to work. Even 500 grit sand paper makes micro gooves to acquire more gunk.
What was the torque on the intake manifold bolts ?
This was awesome, got same motor on my jon boat.
cleaned carb (but not as thoroughly as i just viewed) after 3yr non use as it wouldnt start starts now and runs well but needs partial 1/2 choke at all throttle settings or it will die ...guessing i should have cleaned out the barrel like part with all the little holes like you did ? or do you think my problem involves another part? ps. great informative video!
I have the 20 HP Mercury 4 stroke, and I think they are pretty much the same motor. My motor will idle, all though it is rough, but if I open the throttle, it bogs down. Every once in a while it will idle up and run full speed but only for a few seconds. Any idea why it would act like that? Great video... I will be replacing the Impeller soon thanks!!!!!!
Having the same problem with a merc 15... Im thinking the carb
What was it ?....mine to
I’d guess the fuel tank if it’s not the carb. Look into it. 🤷🏻♂️
Having same problem 😅 Could you tell me what was the problem and how to repair ?Thanks
thank you for helping us.
Excellent video thank you 😊
Great video, thank you.
Which one is the idle air passage?
Thanks for sharing! Question. Have 2012 Tohatsu 15hp 4 stroke idles perfect and runs at high speed just has stutter going from idle and transitioning. Low speed or high speed jet issue ?
Where can I find a complete rebuild kit at. Great video mine is leaking from the top and from the plunger looking thing on the side.
awesome work very clean and well explained ,found u channel looking for a video that can help me fix a problem on a 2013 15hp stars right up runs good and fast but when i slow down engine cuts off and has a brand new carburetor i noticed on this video the idle screw is 5 1/2 turn mine came with 1 3/4 turn not sure thats the problem is getting the spark plugs black on 1 side and light orange on the other side , me tiene loco brother ,any tips that might help ? thanks
Though loosen a screw was counter clockwise
Great video, I took mine apart and I can’t figure out how that plastic clamp is supposed to go on the shifter rod and what is its purpose
Question;
Is it possible to add an
in- line fuel filter after the fuel pump and before the carburetor?
Thanks for the awesome video!
Hi. Have you ever heard of needing to add about twice the amount of recommended lower gear oil ? I drained my 2017 15hp. Manual says 370ml to fill. I had to add about 700ml before it started to come out of top hole.
Hey bud I have a question. At 15:14 what are those two cables for or what are they plugged to? I’m reassembling a carb that I did not take apart and having trouble finding where that plugs to or if it plugs to anything. Thanks!
Hey!! Bro thanks for sharing! I think I'm going to need your help soon just got one motor just like it! I haven't tasted in water! Hey bro que tu cres que sea lo prendi hoy solo con muffs pero se apaga después de unos 15 minutos tu cres que sea el carburador
I have a question. How the part (narrow part of the notes or outside) must be inserted correctly at the time of the recording 10:45
I saw that too. The brass sleeve/tube has a ball check valve inside. The accelerator pump pushes fuel UP that channel in the carb bowl THRU that brass sleeve. It would seem that the flat end of the sleeve goes in first and the smaller end is on the top at the rubber gasket. Otherwise, the check valve would block the flow of fuel to the needle jet that was shown earlier that injects fuel right into the barrel. Am I thinking correctly? This is obviously a very important point that was skipped over in an otherwise excellent video.
Me podrias ayudar tenhob1 mercury 15 hp y cuando lo uso pierde fuerza y le doy todo el gas y se acelera solo y ya como a los 10 min de llebarlo fallando ya jala bken cres q sea q esta suscio el carburador
hi what year ? i guess i missed it
nice video
My idle screw has a plug over it
Do you know if this is the same process for an 08 15 hp looks like the exact same carburetor
Sorry just finished the video and realized you state it right in the audio amazing video
Thanks bro
Where would the model # be on this?
👍🌹👍🌹👍