You should mod new oil pumps for the 3SGE and sell them...most guys would rather buy it from someone that has been there and done it "right" * 3SGE engines really do punch way above their weight, be a shame to lose one like you previously did
I'm confused; You measure a 7.5mm total depth for the valve body (6.5+1mm retainer clip). After this mod you 've shimmed 3mm with the plug (10mm plug but sitting flush to end of valve body) + another 3mm with washers...the spring's travel distance is now only 1.5mm? Am I reading that right?
Is there on top of the little piston a seal? I have a 3sge gen2 build and when the engine stands over night it takes 3 seconds to build oil pressure could the seal of that little piston be the problem?
The piston is part of the system that regulates the maximum amount of pressure created by the pump, other than damage only if any debris is preventing it from totally closing can delay oil pressure. Apart from incorrect oil clearances on the mains, you should check oil filter return/ anti drain seal, is the oil too thick for your application, check clearances on the old pump rotor/shaft/housing, is the oil pickup tight and sealed
I did the same exact thing on my 5SGTE build too. Later i blocked it and went for an external oil pressure regulator wich lets me adjust the pressure up and down.
@@mwpaus Hey Mark, I used rhis exact unit only with AN10 lines instead of 12 wich is in the link, it is a Peterson oil pressure regulator, it works really good for me I can set the maximum oil pressure to whatever I like as long as the pump can provide the flow of course. www.ebay.com/itm/Peterson-Fluid-09-0161-Oil-Pressure-Relief-Valves-12AN-In-Out-NEW/143910360250?_trkparms=ispr%3D1&hash=item2181b9d4ba:g:d2oAAOSwfW1f9i~9&amdata=enc%3AAQAFAAACgBaobrjLl8XobRIiIML1V4Imu%252Fn%252BzU5L90Z278x5ickk7d4nremBkvNKtcC0ZwqXDFzfA1F6FYHx6xJyUAhUCKNRaVHy4q5%252FW3vEejpJk5H7rDMunVD8UhE0DMBCKkeZSeXMMNa%252BXC9lJ7HLN6Kay4ryEp8za60qQmIJMgw02LMh%252BfvKfS%252BM9ZAMN8HaQPmAymgWaCXnalf4hIseeEAowDCXUpS4wTdXEJl%252FFTw1lYk0w0UwYzoVuGVS4hxbO3dxTpQaonQo591IAS3B8cpVwcay3BGosNO7BO1MZa962wiIh6vHQ5vpincleehgHS%252BlrGRAr44GXPD5dQVEH9G9z%252FoFTeNwtDLUhtnR7fPeyoFp7oBtqwcLT0xf3jpvabYNK3CMMRXptJDRBs9Bkid2KN9b4wQhytEbVGgMFuwGoJvsEGiDVri%252BYIMeMxdoAc83tNb9hHXi1CWpbqfxkEUPrtYQxzaRsVAQyyOMq58ORv20kCFMq4%252Bz%252Bxs4PcYrdouSUVPOIP7nufUKDTSkCQJqb2m9PLOpQh0Lfd0VaFAfBDsvvqphwlyxq3uSLE6LmKqphGGtAogmcSR0nfHBCLcbxy7obStL%252Biq1KLM63rOuBNSEUpNPwRctAzRQfDRhO3BwgUG0JGDT%252BTV27rUpLfKNrTgJnAQCfEHEmnAwRT1ukn9Q688gysFaoXA7UemsGRdfaVU0Yv8k%252BGZnFpV88h%252FNDYjUfBiat5T3KRBdJazS3CD3GDc%252BkiQWOqAp7ZzOQsAdjg%252BIMTVGfdzQAWzfQOyS%252BC3HoJ4HE1vygSYs4ekjLqGOSjoZsfJ0ybVVmJPy8ltFjv81Gg9K0zG%252B1hda4kgvMzc%253D%7Ccksum%3A143910360250b5342c27562b48f88812b0bddb8b0225%7Campid%3APL_CLK%7Cclp%3A2334524
@@mwpaus If you would like to do the same thing to your car/project and are confused about how to plumb it to make it work I can explain/show you how I did mine, not saying that how I did it is the right or best way to do it though but it works for me.
@@fdfx3 thank you very much. Ive got an idea of how i would use it... I would remove the factory valve, TIG up the relief hole, then plumb it between the block and my remote oil filter mount. Pretty simple really. What max pressure do you have it set to?
@@mwpaus Yes it's really that simple, for the returnline for the relief line or whatever you would call it I just made a block of plate for the oil level sensor and put an AN fiting there so it would drain back through there. I had the pressure set to 6,5 kg/bar or 92,43 psi, but I'm having problems with the head filling up with oil and pushing it out the PCV pipe on the rocker cover after long periods of WOT, so I reduced the pressure down to 5,5kg/ 78,21psi to help with this problem. So far I haven't gotten around to find a fix or the source of my problem with the the rocker cover filling up, maybe I need an oil restrictor to the top or have excessive bearing clearances on the camshaft or have too much blow by so that the oil won't drain back propperly. If anyone have had any problems with this I would like to hear about it. So 5,5 is what i'm running at the moment, if I could fix my drain back problem I would probably increase it to 92 psi, but I'm yet to figure that out.
How much would you charge if I would purchase an oil pump for a 3SFE, a 1997 oil pump for a RAV4? How much would this mod increase the oil pressure? Can it be used on the street, turbo?
@@rm2932 I got my motor 5SFe still at Machine shop, I got the Motor Powder coated, I can’t believe they took a year on this project, custom cut forged pistons, t Rods, bored cylinders, 10:1 compression even though I’m supercharging after break-in, the pistons took 5 months , they said due to covid, all delays excuses are covid I want to raise my oil pressure when i get my New oil pump Housing My motor is almost complete soon I kept original head instead of putting 3sgt head which has to timing pulleys, intake exhaust, mine is original 1 pulley drives both cams, The grinded the center piece in head, thermal insulation costing on pistons. Oh & stronger springs for lifters, new valves, i told them I may run it 10 or 12k rpm, but wow, you got yours 14k rpm. I’m going yo check with them on springs since they’re waiting on powder coating to finish before they assemble everything
14.000 RPM ?!? Incredible !!! Great explanations !!!
You should mod new oil pumps for the 3SGE and sell them...most guys would rather buy it from someone that has been there and done it "right"
* 3SGE engines really do punch way above their weight, be a shame to lose one like you previously did
Good info! Keep it up!!!!!
Ten problema con un motor de Toyota Camry año 92 la lubricación muy baja y le rectifique el sigueñal y nada que sube la presión del aceite
Hi Ryan - What size tap did you use? 3/8" is too small, it looks closer to 1/2" diameter.
Thank you for the awesome video!
Videos en español porfa de la bomba de aceite del Toyota Camry año 92
Bro, i have some questions about aem pro. Could you help me
Can you share the size of the plug? thanks
Thanks for sharing, really interesting 👍
I'm confused; You measure a 7.5mm total depth for the valve body (6.5+1mm retainer clip).
After this mod you 've shimmed 3mm with the plug (10mm plug but sitting flush to end of valve body) + another 3mm with washers...the spring's travel distance is now only 1.5mm? Am I reading that right?
great video! would you mod the ACL oil pump for a 500hp 3sgte? i got the upgraded oil pump for it
Hello, can you help me to modify my DD 3sfe oil pump or the materials I need? I'm from Chile, I don't understand much English
Is there on top of the little piston a seal?
I have a 3sge gen2 build and when the engine stands over night it takes 3 seconds to build oil pressure could the seal of that little piston be the problem?
There is no seal at the top
The piston is part of the system that regulates the maximum amount of pressure created by the pump, other than damage only if any debris is preventing it from totally closing can delay oil pressure. Apart from incorrect oil clearances on the mains, you should check oil filter return/ anti drain seal, is the oil too thick for your application, check clearances on the old pump rotor/shaft/housing, is the oil pickup tight and sealed
I did the same exact thing on my 5SGTE build too.
Later i blocked it and went for an external oil pressure regulator wich lets me adjust the pressure up and down.
Interesting... what external reg did you use?
@@mwpaus Hey Mark, I used rhis exact unit only with AN10 lines instead of 12 wich is in the link, it is a Peterson oil pressure regulator, it works really good for me I can set the maximum oil pressure to whatever I like as long as the pump can provide the flow of course.
www.ebay.com/itm/Peterson-Fluid-09-0161-Oil-Pressure-Relief-Valves-12AN-In-Out-NEW/143910360250?_trkparms=ispr%3D1&hash=item2181b9d4ba:g:d2oAAOSwfW1f9i~9&amdata=enc%3AAQAFAAACgBaobrjLl8XobRIiIML1V4Imu%252Fn%252BzU5L90Z278x5ickk7d4nremBkvNKtcC0ZwqXDFzfA1F6FYHx6xJyUAhUCKNRaVHy4q5%252FW3vEejpJk5H7rDMunVD8UhE0DMBCKkeZSeXMMNa%252BXC9lJ7HLN6Kay4ryEp8za60qQmIJMgw02LMh%252BfvKfS%252BM9ZAMN8HaQPmAymgWaCXnalf4hIseeEAowDCXUpS4wTdXEJl%252FFTw1lYk0w0UwYzoVuGVS4hxbO3dxTpQaonQo591IAS3B8cpVwcay3BGosNO7BO1MZa962wiIh6vHQ5vpincleehgHS%252BlrGRAr44GXPD5dQVEH9G9z%252FoFTeNwtDLUhtnR7fPeyoFp7oBtqwcLT0xf3jpvabYNK3CMMRXptJDRBs9Bkid2KN9b4wQhytEbVGgMFuwGoJvsEGiDVri%252BYIMeMxdoAc83tNb9hHXi1CWpbqfxkEUPrtYQxzaRsVAQyyOMq58ORv20kCFMq4%252Bz%252Bxs4PcYrdouSUVPOIP7nufUKDTSkCQJqb2m9PLOpQh0Lfd0VaFAfBDsvvqphwlyxq3uSLE6LmKqphGGtAogmcSR0nfHBCLcbxy7obStL%252Biq1KLM63rOuBNSEUpNPwRctAzRQfDRhO3BwgUG0JGDT%252BTV27rUpLfKNrTgJnAQCfEHEmnAwRT1ukn9Q688gysFaoXA7UemsGRdfaVU0Yv8k%252BGZnFpV88h%252FNDYjUfBiat5T3KRBdJazS3CD3GDc%252BkiQWOqAp7ZzOQsAdjg%252BIMTVGfdzQAWzfQOyS%252BC3HoJ4HE1vygSYs4ekjLqGOSjoZsfJ0ybVVmJPy8ltFjv81Gg9K0zG%252B1hda4kgvMzc%253D%7Ccksum%3A143910360250b5342c27562b48f88812b0bddb8b0225%7Campid%3APL_CLK%7Cclp%3A2334524
@@mwpaus If you would like to do the same thing to your car/project and are confused about how to plumb it to make it work I can explain/show you how I did mine, not saying that how I did it is the right or best way to do it though but it works for me.
@@fdfx3 thank you very much. Ive got an idea of how i would use it... I would remove the factory valve, TIG up the relief hole, then plumb it between the block and my remote oil filter mount. Pretty simple really.
What max pressure do you have it set to?
@@mwpaus Yes it's really that simple, for the returnline for the relief line or whatever you would call it I just made a block of plate for the oil level sensor and put an AN fiting there so it would drain back through there.
I had the pressure set to 6,5 kg/bar or 92,43 psi, but I'm having problems with the head filling up with oil and pushing it out the PCV pipe on the rocker cover after long periods of WOT, so I reduced the pressure down to 5,5kg/ 78,21psi to help with this problem.
So far I haven't gotten around to find a fix or the source of my problem with the the rocker cover filling up, maybe I need an oil restrictor to the top or have excessive bearing clearances on the camshaft or have too much blow by so that the oil won't drain back propperly. If anyone have had any problems with this I would like to hear about it.
So 5,5 is what i'm running at the moment, if I could fix my drain back problem I would probably increase it to 92 psi, but I'm yet to figure that out.
Looks like Alltrac101 taught you well
I came up with this on my own after popping the clip out 2 times
@@rm2932 Sure you did just like the blocks you figured out
How much would you charge if I would purchase an oil pump for a 3SFE, a 1997 oil pump for a RAV4? How much would this mod increase the oil pressure? Can it be used on the street, turbo?
From Where & what part is the plug
Just an NPT plug that is aluminum
@@rm2932 you mentioned that the ring clip may pop out if spring of spacing is modified for higher oil pressure?
Any specific size npt plug?
@@rm2932 I got my motor 5SFe still at Machine shop, I got the Motor Powder coated, I can’t believe they took a year on this project, custom cut forged pistons, t Rods, bored cylinders, 10:1 compression even though I’m supercharging after break-in, the pistons took 5 months , they said due to covid, all delays excuses are covid
I want to raise my oil pressure when i get my New oil pump Housing
My motor is almost complete soon
I kept original head instead of putting 3sgt head which has to timing pulleys, intake exhaust, mine is original 1 pulley drives both cams, The grinded the center piece in head, thermal insulation costing on pistons.
Oh & stronger springs for lifters, new valves, i told them I may run it 10 or 12k rpm, but wow, you got yours 14k rpm. I’m going yo check with them on springs since they’re waiting on powder coating to finish before they assemble everything
@@SteveSolaka ⁰0
@@rm2932 what does that mean?