It's too bad the board, superintendent, or whoever made the rule you can't film inside the gates hasn't been flushed out by now. They should have realized your CZcams channel benefited not only you but also the cemetery. I always thought all the filming you did was done with respect.
Looks like a lot of fun I wish I was there doing with you I take things apart get run I put a rear end in my old Camaro 1970 all by myself took it all apart rebuilt it and put it back in again and it worked so the frame broke oops old age 1970
Hey Bill you can get some UV oil leak detector dye and a blacklight pretty cheap on amazon, fill 'er up with dyed oil and all of your leaks will light up bright green. YT has some good videos that show how it works.
Replaced a lot of clutch’s on cars so I don’t see how the tractor was even pulling with all the oil on the clutch and pressure plate. Good job, thanks for sharing the video looking forward for more!!
Bill you have the tractor split in my honest opinion it would be a great time to replace anything that wears (thrust bearing, clutch plate, All seals etc) while you have it that far apart.. I did the same thing and only replaced the clutch plate and 18mths later I had to do it all again to replace the thrust bearing, that time I replaced everything
you should have screwed in the 3 bolts where the pressure plate fingers are in line with to take the pressure off the flywheel before you removed the 6 mounting bolts it makes it easier to remove and reinstall the pressure plate and disk, that is a taper pin i believe it only goes one way
it supost to feel like -2 with frost here in pei wich not looking forward for winter but snows in the winter be a good test on my big powerful st430 20hp30'' snowblower wich hopefuly be at my dealer soon from the states
Yes but check out a youtuber called silvernews. He had news on the next farm sim game.pretty big news from what I saw. I think I it will make the game the most close to real life it has ever been.
Bill, you keep opening new cans of worms with each fix. What I would do is take the whole tractor apart, drive late at night to where you bought the tractor and dump it in his driveway, then leave.
This is painful to watch,..why would you attempt to even do this repair if you don't know what your doing without manuals to refer to, which are easily obtained
ok.. So please tell me what I'm doing wrong... Instead of saying I did it wrong.. That would be helpful.. Btw Ive split another 2n apart 2 times before! :)
Nice work Bill, feels like the old days in the shop. Thanks and be careful with the jacks.
It's too bad the board, superintendent, or whoever made the rule you can't film inside the gates hasn't been flushed out by now. They should have realized your CZcams channel benefited not only you but also the cemetery. I always thought all the filming you did was done with respect.
I Was really excited to see this! Thanks!
Wow Bill, what a project. Take your time, you will get it......
Wowwee! Your up to your elbows now! Great series.
Very cool 👍😎👍
I’m a Muncie 4 speed guy and my guess is the oil is coming from the input shaft seal.
Looks like a lot of fun I wish I was there doing with you I take things apart get run I put a rear end in my old Camaro 1970 all by myself took it all apart rebuilt it and put it back in again and it worked so the frame broke oops old age 1970
Wow you did it now you pull it all apart and found a pile mess you're really good what you do so you can figure it out
Hey Bill you can get some UV oil leak detector dye and a blacklight pretty cheap on amazon, fill 'er up with dyed oil and all of your leaks will light up bright green. YT has some good videos that show how it works.
Replaced a lot of clutch’s on cars so I don’t see how the tractor was even pulling with all the oil on the clutch and pressure plate. Good job, thanks for sharing the video looking forward for more!!
no idea. it pulled the plow pretty good really. but I’m surprised too
BILLSTMAXX Good Job! Thanks for Sharing!!
Bill you have the tractor split in my honest opinion it would be a great time to replace anything that wears (thrust bearing, clutch plate, All seals etc) while you have it that far apart.. I did the same thing and only replaced the clutch plate and 18mths later I had to do it all again to replace the thrust bearing, that time I replaced everything
that was the plan. hopefully it’s not a total replacement
Hope you got deep pockets $$ bill
you should have screwed in the 3 bolts where the pressure plate fingers are in line with to take the pressure off the flywheel before you removed the 6 mounting bolts it makes it easier to remove and reinstall the pressure plate and disk, that is a taper pin i believe it only goes one way
the new kit comes with the alignment pin
That fork has a roll pin that drives in and out not a bolt.
I wonder if the main bearings are tight and the crank isn't wondering Bill ?
May be a problem too.
Would the pilot shaft be leaking? Shouldn’t the inner housing be dry?
could be.. Something is really bad somewhere
it supost to feel like -2 with frost here in pei wich not looking forward for winter but snows in the winter be a good test on my big powerful st430 20hp30'' snowblower wich hopefuly be at my dealer soon from the states
Bill checkout yesterday’s tractor for parts
Bill get your step Dad to take a look and help guide you through this
You won't break the flywheel bolts loose without using an impact wrench bill.they are torqued in at anywhere from 50 to a 120 foot pounds of torque.
fire up the air compressor.
Yes but check out a youtuber called silvernews. He had news on the next farm sim game.pretty big news from what I saw. I think I it will make the game the most close to real life it has ever been.
Bill, you keep opening new cans of worms with each fix. What I would do is take the whole tractor apart, drive late at night to where you bought the tractor and dump it in his driveway, then leave.
lol.
Has the tractor ever been separated before you got it?
I’m not sure. likely had a clutch replaced.
first
I edited this comment so The replies don’t make sense
Brayden ALVEY gloves are for babies. Real men don’t wear gloves!
should have .. was really messy
Real Men Dont wear gloves
Justin Williams then you don’t have to clean your hands after or do your just Throw them away
Midnight Runner 68 but then you don’t have to clean your hands after or do your just Throw them away
And again we got that one rude person.
Who? ill feed them to my chickens!
BILLSTMAXX that one guy who always dislikes your videos
@Tsunauticus III true that! Bill is an awesome guy at what he does!
This is painful to watch,..why would you attempt to even do this repair if you don't know what your doing without manuals to refer to, which are easily obtained
Only one way to learn.
ok.. So please tell me what I'm doing wrong... Instead of saying I did it wrong.. That would be helpful.. Btw Ive split another 2n apart 2 times before! :)