It's the moter in the machine it's slightly rusted due to the wet filter being used. I know the response is 1 year but I just seen this video I fixed one on my channel. If you remove the motor give it some spins with a screw driver the rust particles will come out then put it back in machine.
Unfortunately, you're right. I disassembled my Tineco down to the motor. There was rust, and the motor wouldn't turn. It's working again for now, but it's only a matter of time until it breaks down again. Did you spray any rust remover or something else into the motor? I'm not sure how this can happen to a device that costs over 300 EUR. Thank you for your suggestion! Perhaps you could make another video that's a bit more structured, showing exactly how to access the motor. Thanks a thousand times for your advice.
Si, il problema è il motore che si era bloccato con la ruggine. Soluzione, con un cacciavite sottile delicatamente cercare attraverso i piccoli fori che accedono al motore di aspirazione far girare la ventolina, con aria compressa far cadere la ruggine rimossa e spruzzare all'interno sempre attraverso i fori un po' di spray sbloccante. Ripassare l'aria compressa sempre nel motore, lasciare asciugare 5 minuti e riprovare accensione. Ha ripreso a funzionare. Ho capito anche che il problema è stato causato dall'uso della Tineco senza il filtro, l'acqua si è infilata nel motore in maniera abbondante... errore da non fare assolutamente. Fare sempre asciugare il filtro almeno 24 ore all'aria, mai usarlo bagnato. La colpa è stata della mia scarsa manutenzione.
I had the same issue and after seeing some videos on how to fix that. They all suggest to dissassemble all but i have been fix it without opening it. You need just to put D40 on the hole above the dirty water tank and give it some minutes then run the tineco
Anyone ever find a solution? I purchased 2 one for my work and home. I have had both less than 2 years sent them to tineco twice for repair. It's doing the same thing again. Is there an easy fix?
I hate my tineco. It la only worked for about a total of 30 floor cleans in the two years I e owned it. It’s been broken most of the time. I’ve returned it and they ‘fixed it’. It worked for about another 10 times. It’s broken again. They say the warranty is up and will fix it but I have to pay them.
any problem with the machine, it is recommended that you send to customer service for the repair. Usually its not that expensive..For the motor i have been charge around $75 and warranty for 6 months
The suction fan stucked, or suction motor not working, i fiddle the suction holes with a stick and it's working again. So I guess I'm lucky it's just a stucked fan.
Mine wasn't charging at all. I had to send it back to the company. 7 months later it is doing the same exact thing not charging. They want me to send it to them again. I am over it. I have decided to cut my losses. I will never buy another product from them
Same here. Mine just started this shit. I will get the new 5S Pro 2 tomorrow. I hope I do not have this problem again. One Question, guys? have you been using a different cleaning detergent? I could not get Tinco detergent. They were sold out and used another brand. Could this have been a problem? Sorry for all of us.
One of the comments said to hold the power button and self cleaning button together at the same time off of the base and that sent it to reset and it worked again! I’ve sent mine back FOUR times and the last time they sent it back with a problem it didn’t even have before. For the inconvenience they sent me some soap lol.
Very good product and you will start facing problems after 6 months of usage. They have very expensive spares (ex: roller cost 3000/- against 600/- from other brand, mopping liquid costs more than 1000/- per liter). They have EXTREMELY BAD SERVICE support. Battery is abruptly shutting off which they aren’t not resolving for last 3 months. This is my 3rd Mopping machine. After paying more than 50% premium against other brands, I’m not satisfied with this product.
Essayez cette manipulation qui a fonctionné pour moi. Mettre lappareil en charge puis appuyer sur le bouton du lavage automatique et le bouton démarrer en même temps. L'appareil se mettra en reinitialisation, il va faire un lavage en profondeur puis se remettra en route normalement. Je croise les doigts pour tous.
I'm a small repair shop. It came with such a phenomenon. I disassembled. The suction motor is not working. Soaked or similar. Neither the engine nor the BLD processor is available. The line is over ....
Hi, just wondering, do you know if the main control chip or microcontroller on the motor was the problem, or if it was other components in the motor? Would you be able to post a picture of one of these motors? Thanks
This floor mop is piece of work! Some day I mean most of thr day when i use it leave streak of water especially when you move it backward more leak. I cleaned debris channel got all the junk out and changed roller still not working always puddle of water. Pos. Yeah when you idle it make it stand more water just leaked
Anche per me brutta esperienza L ho riparato troppe volte Adesso non più in garanzia, mi dice che non ho inserito il rullo bene .ho pulito e rimontato,resettato..ma nulla .
This machine is so badly engineered... Owned one, stopped working after a while. Requested assistance, they sent me another one after I sent back mine. Then the new one also stopped working. They sent another one without wanting back the last. I own two of them and each and eveyy one has the same problems. All the metallic parts (screws included) are rusting after a while. Even the impeller is rusting, since it's made out of metal. It's not that difficult for water to get to the motor. If you don't use them at least two or three times a week, the impeller gets stuck again due to rust.
One pf the comments said to hold the power button and self cleaning button together at the same time off of the base and that sent it to reset and it worked again!
Нашел фикс. Снисаем контейнер для воды. Нажимаем на 20 сек очистку на зарядной станции Далее снимаем с зарядки и включаем ее без контейнера для воды. Если не пофиксилось то разбираем. Смотрим мотор и передаточный элемент. Если все норм крутится и не закислелось повторяем первые пункты
ho risolto.per 6 mesi non funzionava e un giorno per puro caso ho risolto staccando un connettore,(bisogna arrivare alla scheda ) senza quel connettore é ripartito il motore aspirazione, senza il connettore poi ho provato a fare la pulizia automatica e mi dava errore vasca vuota. poi ho inserito il conettore ed é ripartito, ora funziona. spero di essere d'aiuto a qualcuno. il connettore e quello rosso in alto a sinistra.
@@m4rtin83 ti ringrazio, ma ho appena ricevuto una mail dal centro assistenza con un video allegato in cui mi spiegano come resettare la macchina. Vediamo cosa succede. Casomai ti contatto
It's the moter in the machine it's slightly rusted due to the wet filter being used. I know the response is 1 year but I just seen this video I fixed one on my channel. If you remove the motor give it some spins with a screw driver the rust particles will come out then put it back in machine.
Unfortunately, you're right. I disassembled my Tineco down to the motor. There was rust, and the motor wouldn't turn. It's working again for now, but it's only a matter of time until it breaks down again.
Did you spray any rust remover or something else into the motor? I'm not sure how this can happen to a device that costs over 300 EUR.
Thank you for your suggestion! Perhaps you could make another video that's a bit more structured, showing exactly how to access the motor.
Thanks a thousand times for your advice.
Si, il problema è il motore che si era bloccato con la ruggine. Soluzione, con un cacciavite sottile delicatamente cercare attraverso i piccoli fori che accedono al motore di aspirazione far girare la ventolina, con aria compressa far cadere la ruggine rimossa e spruzzare all'interno sempre attraverso i fori un po' di spray sbloccante. Ripassare l'aria compressa sempre nel motore, lasciare asciugare 5 minuti e riprovare accensione. Ha ripreso a funzionare. Ho capito anche che il problema è stato causato dall'uso della Tineco senza il filtro, l'acqua si è infilata nel motore in maniera abbondante... errore da non fare assolutamente. Fare sempre asciugare il filtro almeno 24 ore all'aria, mai usarlo bagnato. La colpa è stata della mia scarsa manutenzione.
I had the same issue and after seeing some videos on how to fix that. They all suggest to dissassemble all but i have been fix it without opening it. You need just to put D40 on the hole above the dirty water tank and give it some minutes then run the tineco
Mine is currently doing this too. Please update if you hear of a sign solution. I’ve emailed support, but no response yet. ☹️
Anyone ever find a solution? I purchased 2 one for my work and home. I have had both less than 2 years sent them to tineco twice for repair. It's doing the same thing again. Is there an easy fix?
The very first time I turned it on it did this exact same thing! Any solutions?
I hate my tineco. It la only worked for about a total of 30 floor cleans in the two years I e owned it. It’s been broken most of the time. I’ve returned it and they ‘fixed it’. It worked for about another 10 times. It’s broken again. They say the warranty is up and will fix it but I have to pay them.
any problem with the machine, it is recommended that you send to customer service for the repair. Usually its not that expensive..For the motor i have been charge around $75 and warranty for 6 months
Same problem here! Can I know how did you fix it?
Any updates? The same thing just happened to mine. I contacted customer service and they say it’s in warranty. So we will see
Did the replaced u for free or asked payment?
The suction fan stucked, or suction motor not working, i fiddle the suction holes with a stick and it's working again. So I guess I'm lucky it's just a stucked fan.
Thank you for your solution; it worked for me as well, fortunately!!!
Mine wasn't charging at all. I had to send it back to the company. 7 months later it is doing the same exact thing not charging. They want me to send it to them again. I am over it. I have decided to cut my losses. I will never buy another product from them
Any solutions?!
The roller brush not spinning but the programmed are ok only the roller brush is not functioning
J’ai exactement le même problème avez vous trouvez la solution
Same here. Mine just started this shit. I will get the new 5S Pro 2 tomorrow. I hope I do not have this problem again. One Question, guys? have you been using a different cleaning detergent? I could not get Tinco detergent. They were sold out and used another brand. Could this have been a problem? Sorry for all of us.
One of the comments said to hold the power button and self cleaning button together at the same time off of the base and that sent it to reset and it worked again!
I’ve sent mine back FOUR times and the last time they sent it back with a problem it didn’t even have before. For the inconvenience they sent me some soap lol.
The same thing just happened to my machine as well. Do you have a solution?
You need to put hot water (60-70 Degrees) in water tank ,after that waiting (30-60 minutes) und reset and new start 😉
@@saieedalaiyeb2134 how do you reset it? I have an iFloor 3 though
Same Problem
Very good product and you will start facing problems after 6 months of usage.
They have very expensive spares (ex: roller cost 3000/- against 600/- from other brand, mopping liquid costs more than 1000/- per liter).
They have EXTREMELY BAD SERVICE support. Battery is abruptly shutting off which they aren’t not resolving for last 3 months.
This is my 3rd Mopping machine. After paying more than 50% premium against other brands, I’m not satisfied with this product.
Change the hepa filter to the new one or clean the debris channel
where's the debris channel?
Essayez cette manipulation qui a fonctionné pour moi. Mettre lappareil en charge puis appuyer sur le bouton du lavage automatique et le bouton démarrer en même temps. L'appareil se mettra en reinitialisation, il va faire un lavage en profondeur puis se remettra en route normalement. Je croise les doigts pour tous.
Sa veut pas se mettre en réinitialisant
It doesn't work, still same issue.
Thank you thank YOU!!!! It worked for me!!
Mine just started doing this today
I'm a small repair shop. It came with such a phenomenon. I disassembled. The suction motor is not working. Soaked or similar. Neither the engine nor the BLD processor is available. The line is over ....
Hi, just wondering, do you know if the main control chip or microcontroller on the motor was the problem, or if it was other components in the motor? Would you be able to post a picture of one of these motors? Thanks
Same problem 😢
This floor mop is piece of work! Some day I mean most of thr day when i use it leave streak of water especially when you move it backward more leak. I cleaned debris channel got all the junk out and changed roller still not working always puddle of water. Pos. Yeah when you idle it make it stand more water just leaked
Same here
I saw that u press the too long. U need to press it once only do it on the tray to self clean
Mines keeps saying clean the dirty water tray and debris channel. Trust me it’s clean so now what?
Same for me :(
Same here and its my first day using it.
I have the same after 7 weeks of the purchase. Do not recommend buying this
Anche per me brutta esperienza
L ho riparato troppe volte
Adesso non più in garanzia, mi dice che non ho inserito il rullo bene .ho pulito e rimontato,resettato..ma nulla .
This machine is so badly engineered... Owned one, stopped working after a while. Requested assistance, they sent me another one after I sent back mine. Then the new one also stopped working. They sent another one without wanting back the last. I own two of them and each and eveyy one has the same problems. All the metallic parts (screws included) are rusting after a while. Even the impeller is rusting, since it's made out of metal. It's not that difficult for water to get to the motor. If you don't use them at least two or three times a week, the impeller gets stuck again due to rust.
same here
One pf the comments said to hold the power button and self cleaning button together at the same time off of the base and that sent it to reset and it worked again!
Нашел фикс.
Снисаем контейнер для воды.
Нажимаем на 20 сек очистку на зарядной станции
Далее снимаем с зарядки и включаем ее без контейнера для воды.
Если не пофиксилось то разбираем. Смотрим мотор и передаточный элемент. Если все норм крутится и не закислелось повторяем первые пункты
It’s because when you are trying to self cleaning, the machine needs to be put on the charging dock.
A pile of junk on my third one all the same fault
Motor verkostet
worse machine ever. returning mine this week!
ho risolto.per 6 mesi non funzionava e un giorno per puro caso ho risolto staccando un connettore,(bisogna arrivare alla scheda ) senza quel connettore é ripartito il motore aspirazione, senza il connettore poi ho provato a fare la pulizia automatica e mi dava errore vasca vuota. poi ho inserito il conettore ed é ripartito, ora funziona. spero di essere d'aiuto a qualcuno. il connettore e quello rosso in alto a sinistra.
Stesso problema, qual'é il connettore?
@@mdverardi come faccio a mandarti la foto?
@@m4rtin83 ti ringrazio, ma ho appena ricevuto una mail dal centro assistenza con un video allegato in cui mi spiegano come resettare la macchina. Vediamo cosa succede. Casomai ti contatto
Stesso problema...penso sia il motore bloccato ...non sento più aspirare....ho provato il reset ma non funziona....puoi mandare video dell'assistenza?
@@marcobanterla7924 se mi dai la tua mail te lo giro