This guy is a legit vendor and one of his modules fixed my problem. I don't change parts without first diagnosing/testing, and when my '98 Tahoe's battery went stone-cold dead leading to a stuck-on SECURITY light and a no-start, I did seriously comprehensive diagnostics using a factory service manual and multi-meter, checking voltages, grounds, signals, on the harness, at the connectors, etc. So I KNOW my components were good, except for what looked to be a bad module. I purchased a "55" module a few days ago, went through the key relearn process (also had to erase passlock-related dtc codes with a scan tool) and my Tahoe came to life.
I have a 1999 GMC Sierra truck v8 1500 had a key ignition switch put in after that my truck crank up and cut right back off I have to wait thirty minute before it will start
Hey guys, Question I have 99 suburban 6.5 diesel. Security light stays solid no flashing, no off just solid on. I think you said if that's the case the module is the problem. Am I hearing right? I have check every othe sensor. No luck starting. Thx
I bought one for 1998 GMC ; installed it and the relearn did not work. I tried to call the number that came with the instructions , but it did not work. I called Importa auto and the fellow wno help.Basically he said if we can't see your truck in person we can't help you. Truck still does not run.
I have a 1998 chevy blazer, does it have this module? I'm blazer wont start and I've tried everything except this, I've also noticed you don't mention blazers in your description, are blazers also an issue with this? Someone please lt me.know, I'll probably be buying one of these soon. Thanks
If your security light doesn't come on when you turn the key just twist a little further until it does. My 98 Chevy conversion van light wouldn't come on until I turned it to almost start it
I have a 99 Chevy Express van and could not find the passlock module where they say it is in a 99 Safari as a previous customer says his was. Any ideas where it will be? We've looked everywhere under the dash and behind the radio etc.
I'm looking for the passlock module in my 1999 GMC Safari and I can't find one like you show in this video. I need to find it to get the right number off it before ordering from you. It's supposed to behind the radio near the driver's right knee... however, the box I have there says "Remote Function Actuation Module"... is this my Passlock box?
Thats not the box. To get to the module, you need to remove the dash bezel, the radio and stick your hand all the way to the right. Its hidden in a little pocket. Usually held on with one 7mm bolt that is excessively long.
@@ProRebuild You're the best. THANK-YOU! I found it. Now, I have a very strange problem... no matter what I do the "Security" light NEVER comes on, not even for the bulb test with key on. I have verified that bulb works. I've never seen a passlock problem where the light does not come on... have you? I've also verified that fuel to my engine is being killed by the computer. Still - there no security light. Ever.
@@StuntDummyLives Thats surely not a common issue. The ground for the bulb is provided by the passlock module. If you can, check for power to the passlock, and check ground at the passlock. It may be a broken wire.
@@ProRebuild Brother, I appreciate you, your honesty, your knowledge and your videos a LOT. I was so lost. I ran low on oil during the pandemic and my Roadside Service Provider wouldn't/couldn't get me a tow truck so I was forced to drive and blow my engine. I spent a month and built a brand new engine and installed it into my 1999 Astro and it would start and run for 2 seconds then die. Every time. I was pulling my hair out for 2 weeks. I had no security light on the dash and couldn't find the right module. Anyhow, I thought my module would be totally fried and I would need to buy a new one from you. However, you were right, it was just a ground. As soon as I gave a ground to the module, the van fired right up and stayed running. The security light is even working. I cannot thank you enough for helping me!
I had seen a video that you can cut the purple wire and ground it as you turn the key. And take the box out? We did try it and it did work. For how long don't know??? But did say if your battery ever dies you will need the box.
I installed one in my savana but it was a different part number i was able to realern it and get the van running but will there be a problem becaus of the difference in part numbers
Will this cut then injectors off. I replaced my head gaskets had my battery disconnected on my 04 silverado for 2 days and now my injectors will not fire up do to the pass lock. Plz help I just want my truck on the road.
Hi I have a 98 it had been going dead during driving well after a tow. I replaced the ignition module. The truck started first try didn't even do the relearn it ran for about an hour. Then shut of abruptly "glad I made it back in the driveway👍🏻" With security light solid it has been solid since changing the module. Do you think I need one of your repaired devices?
Can a the pass lock from a 1999 blazer Tahoe 4wd 2door engine size 5.7 wrk on a 1999 Chevy suburban 4wd engine size 5.7 can they ener change yes or no does the part number make a difference.
I have a 99 Tahoe the security light stays solid. I tried the key learn and no good. I got my board out today and it looks fine but I'm sure it's done, because when I unhooked it the security light went off
If the light is on solid, the module will not learn the key. Solid light typically means a bad module and you can't usually tell a bad board from a visual inspection.
@@wea.r.e4483 yes we do, we have plenty in stock. Call us at 573-340-3776 if you want to order one over the phone, or you can visit pro-rebuild.com and order one through the site. Thanks!
My 99 Yukon Denali just died on me last week Thankfully in my garage after driving a week to work with the security light Solid, starts and dies immediately. Doing lots of research on the matter as I've been slowly completely rebuilding this truck the past 2 years so it's nearly Done anyway gonna do some testing and pull the module this weekend, what's the core $?
I own a 97 Silverado everyone says that year doesn't have passlock system. It starts then dies, it has no security light on the dash but that passlock module is in it right next to the ashtray! Where I see other guys on youtube pulling it from, it also has the ignition with the 3 passlock wires above the cylinder. It is a Canadian truck maybe they added this in early in Canada? Has anyone else encountered this? Any info would be great. Thanks for the vid!
Do you know anything about the passkey locks. I have a 2003 escalade ext and my key doesn't have the transponder or chip. It's just a standard key. But I saw nothing about having one of these modules in my truck. I know you're dealing with vehicles from 98 to 2002 but I'm just inquiring.
As of this moment, we are selling either over the phone, or on ebay at the link at the top. We don't charge a core on the 55 part number as we have a few hundred of them in stock currently. Feel free to call us at 573-340-3776.
I have a 2001 Chevy 3500 van and on my truck had a no-start I was able to reprogram and it lost programming next day is that a sign that my unit is bad?
*WARNING: FIRST LOOK at your KEY! Does it look WORN-OUT with rounded edges? I actually got two IDIOT lights on the dash come on. ENGINE and SECURITY and I read the code as SECURITY KEY ERROR. Simple, my key was worn out and did not push the lock tumblers high enough any longer. I had the Locksmith make me a key that had taller dimensions by shimming the key in the "KEY" copying machine. This new key pushed the pins up higher like the old stock key used to and it worked fine after that. $25.00 and FIXED!*
Can you clear this up for me, and your viewers . On your gadget that you made there, a blinking light means that it's good, so weird .. On my 99 Chevy SuburbanI I turn the key to the on position, and if I see the light blinking it doesn't start, and when the light is steady on it starts . So you made your gadget to do it in reverse ... Why ?
Blinking means its in "key learning mode". Once the key is learned(After the 33 minute process), the light should turn on for 2-3 seconds before turning off every time you start or key on the truck. If the light stays on while the truck is running, there is likely another fault in the system. My testing rig is not backwards. its engineered the same as a vehicle. -Eric
I have a 99 Chevy Tahoe 1500 do you need the number off the one of my truck before sending me one is that what you said trying to find the understanding that's all I'm interested in purchasing one for my truck
I usually am always able to start it after the 10minute relearn process but it’s starting to get annoying having to do it more frequently lately , is this the part I need to replace for the security light to stop turning on ? There’s a lot of videos on here about cutting wires but I’m not sure I want to mess with wires.
If the truck won't start and the security light is on solid, this is the most likely culprit. If the light is flashing repeatedly, its more than likely not a bad module.
Well yesterday I had to do the 10 minute relearn process because it was flashing and then it started up but the light has been on and stays solid when I’m driving it
@@chrisnunez1025 Do you have a scan tool that can communicate with different modules in your truck? If so, see if you can communicate with that module.
Pro Rebuild no I don’t have one , the sucurity light hasn’t flashed or turned on the past two days truck starts right up. But I know it will do it again eventually. I just want to do whatever I can to fix this problem so I don’t have to deal with it again. I was hoping your module was the problem but I’m guessing it might now be
My security light turn off when turning the key before crank still won't start it cracks it has fuel pressure fuel pump turns on still won't start why key is not the issue why??? Already replaced that box
I checked still no sign of spark and fuel injection electric that is something that is about the security still hope this helps to all to a short of a wire and a lead that is a factory mistake
@@ProRebuild I'll try again see if it's a sensor or something like crack sensor or distributor other been replaced like coil and icm that box it's the problem other wise I will delete all security system by replace by a same 96 or 97 Chevy truck it doesn't have that security system on those truck same type fit and the key is the same with out bats and box
@@benking4252 thats a different system as thats the next generation of truck from this system. It sounds like a wiring issue, as the scan tool is probably providing a power or ground that you are missing.
go to www.pro-rebuild.com and you can order one there through paypal, or call us at 573-340-3776 to pay over the phone. we ship same day by 3pm central time.
Have you thought about reproducing them in their entirety, and having them made in China? You can spec them with whatever chips, resistors, etc. that you want, and they'd be brand new.
Thats an avenue that likely has a whole set of issues associated with it. I think the best course of action is to fix what we have here. We have about 600 of these in stock at any given time.
Htown Stunna My 98 k1500 stopped running due to the passlock, like it starts then dies due to the passlock cutting fuel to the injectors. is yours doing the same thing or something different?
my 98 is doing the same, cranks fires for one second then dies, security light stays lit always, relearns do no good, may try one of these and see if it helps if I can find any details on how hard it is to install or anything
This guy is a legit vendor and one of his modules fixed my problem. I don't change parts without first diagnosing/testing, and when my '98 Tahoe's battery went stone-cold dead leading to a stuck-on SECURITY light and a no-start, I did seriously comprehensive diagnostics using a factory service manual and multi-meter, checking voltages, grounds, signals, on the harness, at the connectors, etc. So I KNOW my components were good, except for what looked to be a bad module. I purchased a "55" module a few days ago, went through the key relearn process (also had to erase passlock-related dtc codes with a scan tool) and my Tahoe came to life.
For those wondering, on 98-00 suburban/Tahoe, it’s directly underneath your CD player. You’re welcome!
I have a 1999 GMC Sierra truck v8 1500 had a key ignition switch put in after that my truck crank up and cut right back off I have to wait thirty minute before it will start
Is how do I get your dumbler
Hey guys, Question I have 99 suburban 6.5 diesel. Security light stays solid no flashing, no off just solid on. I think you said if that's the case the module is the problem. Am I hearing right? I have check every othe sensor. No luck starting. Thx
I bought one for 1998 GMC ; installed it and the relearn did not work. I tried to call the number that came with the instructions , but it did not work. I called Importa auto and the fellow wno help.Basically he said if we can't see your truck in person we can't help you. Truck still does not run.
I have a 1998 chevy blazer, does it have this module? I'm blazer wont start and I've tried everything except this, I've also noticed you don't mention blazers in your description, are blazers also an issue with this? Someone please lt me.know, I'll probably be buying one of these soon. Thanks
If your security light doesn't come on when you turn the key just twist a little further until it does. My 98 Chevy conversion van light wouldn't come on until I turned it to almost start it
I have a 99 Chevy Express van and could not find the passlock module where they say it is in a 99 Safari as a previous customer says his was. Any ideas where it will be? We've looked everywhere under the dash and behind the radio etc.
Is there a way I can test mine at home?
I'm looking for the passlock module in my 1999 GMC Safari and I can't find one like you show in this video. I need to find it to get the right number off it before ordering from you. It's supposed to behind the radio near the driver's right knee... however, the box I have there says "Remote Function Actuation Module"... is this my Passlock box?
Thats not the box. To get to the module, you need to remove the dash bezel, the radio and stick your hand all the way to the right. Its hidden in a little pocket. Usually held on with one 7mm bolt that is excessively long.
@@ProRebuild You're the best. THANK-YOU! I found it. Now, I have a very strange problem... no matter what I do the "Security" light NEVER comes on, not even for the bulb test with key on. I have verified that bulb works.
I've never seen a passlock problem where the light does not come on... have you?
I've also verified that fuel to my engine is being killed by the computer. Still - there no security light. Ever.
@@StuntDummyLives Thats surely not a common issue. The ground for the bulb is provided by the passlock module. If you can, check for power to the passlock, and check ground at the passlock. It may be a broken wire.
@@ProRebuild Brother, I appreciate you, your honesty, your knowledge and your videos a LOT.
I was so lost. I ran low on oil during the pandemic and my Roadside Service Provider wouldn't/couldn't get me a tow truck so I was forced to drive and blow my engine. I spent a month and built a brand new engine and installed it into my 1999 Astro and it would start and run for 2 seconds then die. Every time. I was pulling my hair out for 2 weeks. I had no security light on the dash and couldn't find the right module.
Anyhow, I thought my module would be totally fried and I would need to buy a new one from you. However, you were right, it was just a ground. As soon as I gave a ground to the module, the van fired right up and stayed running. The security light is even working.
I cannot thank you enough for helping me!
My Escalade excepted the key relearn process now the security light goes off but still no start
Are you still in business. Have tried to call phone number and get a recording that the number is not available
I had seen a video that you can cut the purple wire and ground it as you turn the key. And take the box out? We did try it and it did work. For how long don't know??? But did say if your battery ever dies you will need the box.
I installed one in my savana but it was a different part number i was able to realern it and get the van running but will there be a problem becaus of the difference in part numbers
Will this cut then injectors off. I replaced my head gaskets had my battery disconnected on my 04 silverado for 2 days and now my injectors will not fire up do to the pass lock. Plz help I just want my truck on the road.
my 2000 chevy silverado 1500 security lights is on when i driving,what you tinke was the problem
We would have you contact a local mechanic, we can not diagnose a vehicle with a sentence.
Hi I have a 98 it had been going dead during driving well after a tow. I replaced the ignition module. The truck started first try didn't even do the relearn it ran for about an hour. Then shut of abruptly "glad I made it back in the driveway👍🏻" With security light solid it has been solid since changing the module. Do you think I need one of your repaired devices?
What happened is the light turns off but come bk solid
I have a 1998 gmc seirra
I have a 2002 Chevy Express 3500 it starts for 1 second I am trying to find that box in the vehicle do you know where it's at
Can a the pass lock from a 1999 blazer Tahoe 4wd 2door engine size 5.7 wrk on a 1999 Chevy suburban 4wd engine size 5.7 can they ener change yes or no does the part number make a difference.
What u think my original was 75 n ive got 2 55 my truck light goes off n then comes back after a min
How do I know if my module is bad
Hey do you have one for a 03trailblazer I can’t get it to relearn the new key
No that's a different system, these are for the older vehicles.
Does the 2001 Gmc Jimmy SLE use these? If so where is it located?
I have a 99 Tahoe the security light stays solid. I tried the key learn and no good. I got my board out today and it looks fine but I'm sure it's done, because when I unhooked it the security light went off
If the light is on solid, the module will not learn the key. Solid light typically means a bad module and you can't usually tell a bad board from a visual inspection.
@@ProRebuild thank you so much for your response. Do you still have modules?
@@wea.r.e4483 yes we do, we have plenty in stock. Call us at 573-340-3776 if you want to order one over the phone, or you can visit pro-rebuild.com and order one through the site. Thanks!
My 99 Yukon Denali just died on me last week Thankfully in my garage after driving a week to work with the security light Solid, starts and dies immediately. Doing lots of research on the matter as I've been slowly completely rebuilding this truck the past 2 years so it's nearly Done anyway gonna do some testing and pull the module this weekend, what's the core $?
I own a 97 Silverado everyone says that year doesn't have passlock system. It starts then dies, it has no security light on the dash but that passlock module is in it right next to the ashtray! Where I see other guys on youtube pulling it from, it also has the ignition with the 3 passlock wires above the cylinder. It is a Canadian truck maybe they added this in early in Canada?
Has anyone else encountered this? Any info would be great. Thanks for the vid!
Have a 1998 GMC sierra 1500, so this would be the part I need?
We suggest you visually look at your part and match part numbers, thanks
My 99 c1500 has a 16294921 do u sell those. I didn't see on your website
Do you know anything about the passkey locks. I have a 2003 escalade ext and my key doesn't have the transponder or chip. It's just a standard key. But I saw nothing about having one of these modules in my truck. I know you're dealing with vehicles from 98 to 2002 but I'm just inquiring.
The 03' use are different then the ones we sell. Please consult with a mechanic in your area for help, Thanks Adam
Thanks for a great info video, Eric. What's your website called again? And how much is the core charge for the 55?
As of this moment, we are selling either over the phone, or on ebay at the link at the top. We don't charge a core on the 55 part number as we have a few hundred of them in stock currently. Feel free to call us at 573-340-3776.
I have a 2001 Chevy 3500 van and on my truck had a no-start I was able to reprogram and it lost programming next day is that a sign that my unit is bad?
is the light still blinking or is it on solid?
@@ProRebuild the light is solid I just ordered a module on eBay
Could it be in the ignition if vat been replaced
Please contact us through ebay , follow the link www.ebay.com/usr/pro-rebuild
*WARNING: FIRST LOOK at your KEY! Does it look WORN-OUT with rounded edges? I actually got two IDIOT lights on the dash come on. ENGINE and SECURITY and I read the code as SECURITY KEY ERROR. Simple, my key was worn out and did not push the lock tumblers high enough any longer. I had the Locksmith make me a key that had taller dimensions by shimming the key in the "KEY" copying machine. This new key pushed the pins up higher like the old stock key used to and it worked fine after that. $25.00 and FIXED!*
Can you clear this up for me, and your viewers .
On your gadget that you made there, a blinking light means that it's good, so weird ..
On my 99 Chevy SuburbanI I turn the key to the on position, and if I see the light blinking it doesn't start, and when the light is steady on it starts .
So you made your gadget to do it in reverse ... Why ?
Blinking means its in "key learning mode".
Once the key is learned(After the 33 minute process), the light should turn on for 2-3 seconds before turning off every time you start or key on the truck. If the light stays on while the truck is running, there is likely another fault in the system. My testing rig is not backwards. its engineered the same as a vehicle.
-Eric
I have a 99 Chevy Tahoe 1500 do you need the number off the one of my truck before sending me one is that what you said trying to find the understanding that's all I'm interested in purchasing one for my truck
Maurice Snyder did it work for your truck? I have 99 tahoe
Did work? I have 99 Tahoe as well.
I usually am always able to start it after the 10minute relearn process but it’s starting to get annoying having to do it more frequently lately , is this the part I need to replace for the security light to stop turning on ? There’s a lot of videos on here about cutting wires but I’m not sure I want to mess with wires.
If the truck won't start and the security light is on solid, this is the most likely culprit. If the light is flashing repeatedly, its more than likely not a bad module.
Well yesterday I had to do the 10 minute relearn process because it was flashing and then it started up but the light has been on and stays solid when I’m driving it
If it’s not the module do you know what else it can be ?
@@chrisnunez1025 Do you have a scan tool that can communicate with different modules in your truck? If so, see if you can communicate with that module.
Pro Rebuild no I don’t have one , the sucurity light hasn’t flashed or turned on the past two days truck starts right up. But I know it will do it again eventually. I just want to do whatever I can to fix this problem so I don’t have to deal with it again. I was hoping your module was the problem but I’m guessing it might now be
Will a pn#16244555 work in place of a pn#16264955 in a 1999 Chevy Tahoe?
No, thats a 97 style module and its not a passlock. it has to be 16264955.
My security light turn off when turning the key before crank still won't start it cracks it has fuel pressure fuel pump turns on still won't start why key is not the issue why??? Already replaced that box
If the light turns off, the key learn process is complete. Have you checked to see if you have any codes? what about RPM signal?
I checked still no sign of spark and fuel injection electric that is something that is about the security still hope this helps to all to a short of a wire and a lead that is a factory mistake
@@lboss9187 Do you have a scan tool that can communicate with more than just the PCM?
@@ProRebuild I'll try again see if it's a sensor or something like crack sensor or distributor other been replaced like coil and icm that box it's the problem other wise I will delete all security system by replace by a same 96 or 97 Chevy truck it doesn't have that security system on those truck same type fit and the key is the same with out bats and box
You dont carry any for my 98 tahoe. But rock auto has it. Hmmmm...
We absolutely carry them for your tahoe as long as its a 98-00 old body style
Can I purchase one from you
I own a 2000 Chevy Silverado it will not fire up unless I have a code reader hooked up to it soon as I unplug it will shuts off
is this the new body style with the 5.3? or the old body style with a 5.7?
@@ProRebuild 5.3
@@benking4252 thats a different system as thats the next generation of truck from this system. It sounds like a wiring issue, as the scan tool is probably providing a power or ground that you are missing.
Rock auto has them are they the same ones as yours ?
They are typically on backorder and out of stock, as well are more expensive and only carry a 30 day warranty.
I've change it 3 times plus more n nothing
You said on savana and express van that they are easily removed. Where is the exact location on these vans ?
they are above the gas pedal, on the top of the metal dash housing
I have a 2002 Chevy Tahoe, do you make one for this? Is so how much and how can I contact you?
the 2002 uses a different style which is readily available at your local dealership. This will not work in your truck.
Hello great video by the way! I have some questions I think I’m having this issue wats the beat way to get in contact with you?
Our phone number is in the description.
How long does shipping take? I need one for my 1999 Yukon, thanks.
We can ship express and get it to you the following day. Call us at 573-340-3776 and we can get one headed your way asap. -Eric
@@ProRebuild what's the return policy?
@@kingnecio we offer 60 day returns, and lifetime replacement only warranty.
I need ONE for my 99 Tahoe
@@Shackdiesel42 feel free to call us and order one at 576340-3776. 8-5 cst
03 chevy tahoe? Do I need one ?
an 03 tahoe does not have this system so this will not help you.
How do I get One of these modules from you
go to www.pro-rebuild.com and you can order one there through paypal, or call us at 573-340-3776 to pay over the phone. we ship same day by 3pm central time.
How can I order one
call us at 573-340-5776 and have your part number ready!
How do i contact you? I am looking for a bypass for 02 s10 automatic 4 cyl
We do not have the one your looking for, that's a different system. Thanks
arent they code specific
I have a 2000 Chevy astro van with the same problem. Can you send me a number so I can contact you.
You can click on the eBay link in the description also our number is there also.
Have you thought about reproducing them in their entirety, and having them made in China? You can spec them with whatever chips, resistors, etc. that you want, and they'd be brand new.
Thats an avenue that likely has a whole set of issues associated with it. I think the best course of action is to fix what we have here. We have about 600 of these in stock at any given time.
no more chinese junk please.
@@Tomcat71 ok then how about Taiwan? LOL
How much and how can purchase for my 98 chevy Silverado
Htown Stunna My 98 k1500 stopped running due to the passlock, like it starts then dies due to the passlock cutting fuel to the injectors. is yours doing the same thing or something different?
my 98 is doing the same, cranks fires for one second then dies, security light stays lit always, relearns do no good, may try one of these and see if it helps if I can find any details on how hard it is to install or anything
Got to love GM and useless garbage disabling a perfectly good vehicle . Wonder if anyone ever got sued of this junk ?