BOSCH GWS 11-125 CIE ANGLE GRINDER SERVICE BOSCH GWS 11-125 CIE कोना चक्की SERVICE

00:14 stops working when the cable moving
00:23 disassembly of Auxiliary Handle
00:31 disassembly the head from the body
01:00 disassembly of Protective Cover
01:16 disassembly of Round Nut M14
01:20 disassembly of Clamping-flange Ø22,3xØ42 MM
01:28 disassembly of Gear housing/Bearing Flange
01:35 disassembly of Catch Lever and spring
01:44 disassembly of Shim 0,3 MM
01:54 degrease
02:01 with the help of a vice and a 10 mm wrench i will unscrew the Hex Nut M7, SW10
02:14 disassembly ofArmature With Fan 220-240V
02:19 disassembly of Bevel Gear Z=11
02:22 disassembly of Push-button
02:37 disassembly of Housing Cover
02:53 disassembly of Cover
03:05 disassembly of Tapping ScrewDIN7981-ST3,9x13-C-Z/Fastening Clamp/
03:18 HOW TO CHECK a cord of a POWER TOOL (SHORT lesson)
04:23 check of the cord
04:39 first wire fault detection
04:45 disassembly the wires of the Switch
05:44 disassembly of Compression Spring
05:51 disassembly of Air-deflector Ring
06:00 disassembly the wires of the Switch
06:17 disassembly the Switch
06:36 cleaning of the switch
06:53 clean the armature from the carbon with sandpaper
07:08 replace the Carbon-brush Set
07:29 second fault detection (detection of wire insulation wear)
07:50 wire repair
07:55 switch in place
08:01 switch wires assembly
08:10 assembly of Air-deflector Ring
08:17 assembly of Compression Spring
08:21 lubricate the spring (10 TIMES ON OFF )
08:32 connect the wires of the cord with the switch
08:37 connecting wires to the switch
08:45 assembly the wires of the switch
09:08 assembly of Tapping ScrewDIN7981-ST3,9x13-C-Z/Fastening Clamp
09:19 assembly of Housing Cover with Motor Housing
09:29 assembly of Cover
09:34 assembly of Tapping Screw DIN7981-ST3,9x19-F-Z
09:43 lubricate the Push-button
09:55 assembly of Push-button
10:15 assembly of Bevel Gear Z=11with Armature With Fan 220-240V
10:33 screw the hex Hex Nut M7, SW10 with a wrench key 10 mm
11:08 lubricate the gears
11:52 assembly of Catch Lever /Spring
12:13 assembly of Grinding Spindle M14, SW17/Crown Gear Z=38//Gear Housing
12:45 assembly of Armature With Fan220-240V with Housing Cover and Motor Housing
13:12 assembly of Grommet Ø7,3-Ø8,6x67 MM
13:16 assembly of Cover/Tapping Screw DIN7981-ST3,9x19-F-Z
13:56 test
14:06 check of Power Supply Cord EU 4,15m 2 x 1,0mm H07 RN-F
14:23 third fault detection
14:35 remove the damage part (first attempt)
14:55 check for signal
15:23 remove the damage part (second attempt)
15:48 check for signal
16:16 replace the old part with new
21:00 check for signal (coonect the two wires to the switch)
21:14 final test

[@nakosmiltiadis8284]

thank you for this video ,is there a way someone to check the switch with a polymeter ?

[@TheKatr2]

in Continuity mode 3:34
take the polymeter and connect the black lead with the brown wire
and the red lead with blue wire
pull the triger
if you hear the beep sound thi switch working
if you dont hear nothing the switch has problem

[@TheKatr2]

ρε πατριδα μιλα οτι εισαι Ελληνας
γραφτηκα στο καναλι σου

[@nakosmiltiadis8284]

Ευχαριστώ το δοκίμασα και το πρόβλημα τελικά είναι πιο ψηλά στον μοχλό που πιέζει τον διακόπτη.
Σε ευχαριστώ

[@nakosmiltiadis8284]

@@TheKatr2 έχεις κάνει πολύ καλή δουλειά στο κανάλι σου μπράβο!

[@TheKatr2]

@@nakosmiltiadis8284 εγω σε ευχριστω
καλη συνεχεια