02:48 This is a feature called DisplayPort Alternate Mode. You can input the video output from the graphic board to the motherboard and convert it to Thunderbolt4 output. Notice in the following scene that there is only one cable connected to the display (i.e. the video signal and power supply are on the same cable).
They have ability to contact manufacturers to make many things on spot for good prices. Make it very easy for small businesses to turn ideas into products in short time, without much overhead investment.
Ever heard of ram clearance? Which on an itx motherboard is even more important. Out of all the things you could have said about the video, you just had to hate. Nothing about anything else.
Nice case, but acoustically an absolute nightmare. A tiny fan on the motherboard, another one in the PSU (sucking hot air from within the case), and another one mounted as case fan. Then there’s a single fan GPU and low profile fans that also have to spin up quite a bit to move any meaningful amount of air. It would be nice if this case should be little bit bigger, to offer SFX PSU support and better cooling options.
i have had the osmi 3.O, built the sixge k2s and the cooj mq5 and the worst in terms of thermals is the k2s because i got the better ventilation pane of the cooj... the osmi has the advantage of the large 120mm fans pulling from the bottom but its loud when it kicks in... i would give cooj alot of kudos for such a nice design that caters to some of us who dont want a gigantic case of a showrom, but petit enough to pack a punch reasonably too.
nice looking itx case imo i rather get a mini pc like ser6 than build a itx pc if i want performance, i would have go for micro atx or atx build instead
It collects dust and pet hairs. It also gets very hot inside and toasts thermal paste very quicklyl. Then replace thermal paste and clean fan means I need to disassemble almost everything. And it is not fun at all to disassmble such a small thing.@@mehmetonurlu
CPU clearance is 72mm, should have used a NH-L12S instead, the noise and temp would have had a significant improvement. But then again, just for an extra 2cm of width, should have used Ncase M1, with much better temps.
Блин, как же мне нравится этот корпус, да вот жаль, что ни блок питания SFX и полное жидкостное охлаждение поставить, так как просто места нет. Вот был бы по больше, да даже на 1,5 литра, купил бы не задумываясь.
На видео не такой уж и маленький копрус. Если взять какой нидуь NR200P туда и воду поставить можно и SFX БП и любое топ железо, а объем литров 18 всего
as far as i know, it's to run the monitor on a single thunderbolt cable (vs hdmi/dp + power cable) the displayport (from gpu) to motherboard usbc acts as passthrough then he runs a single cable from motherboard to monitor, thunderbolt 4 supports up to 100w so i think whatever motherboard he has apparently supports that, or at least enough wattage for a monitor
2:46 What are the screws that she’s putting onto the WiFi/Bt posts? I’m assuming that they’re “blanks” meant to just cover/protect the posts when not in use? If anyone could tell me the model number or manufacturer of those things I’d really appreciate it.
Definitely the move over intel, amd sips power. I’m getting basically stock scores max power draw 60watts on 7600 using pbo+undervolt. Max 85 degrees in the Dan A4-H2O with wraith stealth cooler
2:34 hey what happened to the duct at 1:57 ? and why would you have to connect thunderbolt to dp cable at 2:45 ? is there a reason? [edit] those were for thunderbolt daisy chain configuration
hi, can you enlighten me on those DP to Thunderbolt? what does it for? and is it giving any benefits at all? and for the end product (display on monitor), he would just plug into the other DP port, wouldnt he?
@@notme6254 it turned out to be configuring thunderbolt devices via daisy chain connection. in order to do that, eGPU'output is fed into motherboard's minidp(thunderbolt bypass port). then the monitor is connected to motherboard's USB-C thunderbolt connector, making motherboard the main source of thunderbold daisy chain connection. you may find diagrams of that on MSI's MEG Z690 series manual. I found this info on MEG Z690 ACE manual on page 18.
@@e_sence thanks for the answer, i have look at MSI's MEG Z690 manual too and quite understand what it means about daisy-chain connection. so according to my understanding, can i say that the motherboard will act as dock/hub or something like that, just to get those bigger and faster transfer bandwidth for other devices that connect to the motherboard later? but for the monitor output, they still use the eGPU right? even though its connected to motherboard's Thunderbolt port?
@@notme6254 quite right. maunual says it can support multiple devices via daisy-chain function of thunderbolt including eGPU. but sending eGPU output in a thunderbolt lane needs some kind of "transfer station" at the motherboard's side, so the MiniDP passthrough port is needed to get eGPU's DP signal to turn into thunderbolt signal and sending that through thunderbolt USB-C connector.
02:48 This is a feature called DisplayPort Alternate Mode. You can input the video output from the graphic board to the motherboard and convert it to Thunderbolt4 output. Notice in the following scene that there is only one cable connected to the display (i.e. the video signal and power supply are on the same cable).
That's good to know! Thanks for the insight!
I just noticed that. So the monitor is a portable ROG monitor
That's cool, I'm having a hard time understanding that too
whats the cons?
@@eeeeeek No cons except requiring a monitor that supports thunderbolt
China is so ahead in the mini-ITX game. My latest build from a few months ago used a Chinese case. There are just so many selections.
If you come here in china they're like 500 cases brand and only few of them are being market outside of china and the rest is only in china market
They have ability to contact manufacturers to make many things on spot for good prices. Make it very easy for small businesses to turn ideas into products in short time, without much overhead investment.
Im thinking using small pc + pcie FPGA card to do many fancy things. The development of itx enables this idea
装电脑真的是装的时候比用的时候开心……
哈哈哈，毕竟拼装后启动成功之类的让人满足，但是用着用着就觉得不够，准备换掉有觉得还可以再战五百年
@@lele-ok4bz 点不亮那就是另一回事了😂
itx用3.0pcie延長線+沒內顯+bios不小心重置=崩潰
电子阳痿
装机被你装出艺术感来了。
With that much heating duct over the CPU I would have just gone with a much taller cooler
That, and def not a 15mm fan.
Seriously
Ever heard of ram clearance? Which on an itx motherboard is even more important. Out of all the things you could have said about the video, you just had to hate. Nothing about anything else.
@@ForTheViolence there are plenty of taller coolers that wouldn’t affect ram clearance, you know.
@@ForTheViolence it’s pretty but this is an sff build, the WHOLE brand is to be as efficient as possible. So it’s not even a BAD nitpick
Nice case, but acoustically an absolute nightmare. A tiny fan on the motherboard, another one in the PSU (sucking hot air from within the case), and another one mounted as case fan. Then there’s a single fan GPU and low profile fans that also have to spin up quite a bit to move any meaningful amount of air.
It would be nice if this case should be little bit bigger, to offer SFX PSU support and better cooling options.
Same thoughts. Hate the acoustics. No no case for me.
Only bottlenecks I see are 1U PSU fan and possible vibrations to metal case. 40mm Noctuas are ridiculously silent
i have had the osmi 3.O, built the sixge k2s and the cooj mq5 and the worst in terms of thermals is the k2s because i got the better ventilation pane of the cooj... the osmi has the advantage of the large 120mm fans pulling from the bottom but its loud when it kicks in... i would give cooj alot of kudos for such a nice design that caters to some of us who dont want a gigantic case of a showrom, but petit enough to pack a punch reasonably too.
nice looking itx case
imo i rather get a mini pc like ser6 than build a itx pc
if i want performance, i would have go for micro atx or atx build instead
recien encuentro este canal a las 3 30 de la madrugada y realmente he disfrutado cada segundo de cada video, amo estar aqui
The case looks really cool, but it's a shame that it doesn't support SFX PSUs 😕.
sfx is too big
For what you need a SFX PSU in such a small case ? Silverstone has a sff PSU with 600w. Its enough for an undervolted 4090.
And with a 90+ PSU æ.
I had a A4 SFX case before and I did enjoy it when I assembled it for the first time. But after that, it's been always a nightmare.
why?
It collects dust and pet hairs. It also gets very hot inside and toasts thermal paste very quicklyl. Then replace thermal paste and clean fan means I need to disassemble almost everything. And it is not fun at all to disassmble such a small thing.@@mehmetonurlu
nice... MSI motherboard with ASUS boot logo.. should be 2x more stable now
First logo with asus is from monitor when receive single from hdmi and than second logo with MSI is from Mobo.
Where are the tweezers, anti-static band and zip ties?
If you get this reference. Never let it get forgotten.
天啊 這男生的手 真美
Chassis: MQ6
CPU: 12600KF
Motherboard: MSI Z690i
Cooling: NOCTUA L9i Black & NA-FD1
Hard disk: ZhiTai TiPlus5000 512G
Memory: G.SKILL Trident Z5 RGB Phantom DDR5 16G*2 5600
Power Supply: FSP Flex-500G
Graphics Card: MSI 3050 AERO
Additional Fans: A4X20 PWM & A12X15 PWM 👍👍
what is case name ?
@@huongson5848 Sparrow-MQ6 6.8L One-piece aluminum itx pc case 😄👌👍
@@adhmadhm2373 thanks
What is the name of the blue thing to lock the cpu?
im curious, why'd you plug the hdmi to the motherboard? does it act as a pass through?
the cooler helps to dissipate heat from the vram too, it makes no sense to cover it with foam
視覺和聽覺的質感享受
除了快乐，装itx还会有什么体验？ 痛苦。。抓狂。。。哈哈哈啊
CPU clearance is 72mm, should have used a NH-L12S instead, the noise and temp would have had a significant improvement. But then again, just for an extra 2cm of width, should have used Ncase M1, with much better temps.
Блин, как же мне нравится этот корпус, да вот жаль, что ни блок питания SFX и полное жидкостное охлаждение поставить, так как просто места нет.
Вот был бы по больше, да даже на 1,5 литра, купил бы не задумываясь.
На видео не такой уж и маленький копрус. Если взять какой нидуь NR200P туда и воду поставить можно и SFX БП и любое топ железо, а объем литров 18 всего
@@Gideon_ZR да, но мне просто очень понравился именно этот корпус.
@@Dich_little а что за заглушки вместо антенн у него?
@@user-in8cs4me8q заглушки? На USB потрах? Это клавиатура и мышь. Если ты про это.
@@Dich_little посмотрите корпус от iqunix
这些声音对我来说简直就是ASMR
Neat. Where do you get all the good-looking cases?
我也很喜歡安裝ITX，家中的desktop全是ITX的，原因一來祟尚短小精悍，二來大機箱放桌面太礙視線
我剛買了個超大機箱，大到可以裝雙系統，設計為服務器機箱（但是很好看😆）。裝了很多風扇和480AIO水冷
Thats the right Direction 🪄
Hi, can you explain why you plug a Displayport cable from a graphic card into the motherboard? Thank you.
显卡信号通过主板的dp in接口输入，再转从主板的雷电接口输出，实现显示器一线通。
@@foni7 就是从DP转接成雷电，这样显示器就不需要接电源?
@@Jordan-zh7ev 支持typc一线通的显示器，可以
as far as i know, it's to run the monitor on a single thunderbolt cable (vs hdmi/dp + power cable)
the displayport (from gpu) to motherboard usbc acts as passthrough
then he runs a single cable from motherboard to monitor, thunderbolt 4 supports up to 100w so i think whatever motherboard he has apparently supports that, or at least enough wattage for a monitor
@@jeen0351 Thank you for your answer, that feels so cool when you just need one cable for almost everything.
装 完了出售吗?哈哈,想自己装 嫌麻烦,看你的视频 就过瘾了
Lo hermoso de estos videos no son solo las hermosas manos, sino los disipadores noctua!
🤗
These cases and builds are great.
at 2:36, did you remove the fan duct completely? or you just placed the fan above the fan duct?
pretty clean!
Me ha gustado mucho ese gabinete.
what's up with the thing you placed on top of the cpu cooler, then have it removed at the end of the video???
每样东西都不是一个品牌 起码颜色统一一个色系看着爽点
nice setup, small so beautiful
Internal graphic amplifier！👍2 in 1.
影片拍得很棒！看得我手好癢
2:46 What are the screws that she’s putting onto the WiFi/Bt posts? I’m assuming that they’re “blanks” meant to just cover/protect the posts when not in use? If anyone could tell me the model number or manufacturer of those things I’d really appreciate it.
Blue Tooth Antenna 3dbi Gain Omni Directional InnerHole Connector Mini for Modem USB Adapter Signal Booster Wifi Repeater Zigbee
How is the fan sound? How's the performance? Does it work as a power cable or USP-C? And why is that cable in the back
直接 5700g + 4000mhz 32gb ram 就够用了 又省电又薄 没必要拖个3050
That case is awesome .... but sooo expensive.
what is the name of the case?
这也太快了了吧，听着好舒服
great cases, but WHERE TO BUY????
Жесть как он зажужжал как только его включили
why you connect Dp port with Tyce C / thunderbort port?
pass through displayport from dgpu to mainboard's thunderbolt, so the usb-c monitor can get display output from the thunderbolt port
because they don't know that you can do this without cable
What do you call the type of screw that used to mount the bottom fan?
If you buy a fan, it will be included in the package
What a nice computer! Otokonoko 😱
the case is the "Sparrow-MQ6" by COOJ
this case is amazing looking!
I want to put an AM5 7000 series in this case. So cool!
it gonna explode 🙃
Definitely the move over intel, amd sips power. I’m getting basically stock scores max power draw 60watts on 7600 using pbo+undervolt. Max 85 degrees in the Dan A4-H2O with wraith stealth cooler
02:32 Isn't it meaningless to put an intake fan right next to the power exhaust fan? I think all the heat will go into the case
whats the connection to the dp port on the gpu to the thunderbolt on the mobo?
That is a tiny monitor. What's the size @foni?
太精致了
what happened to a COOJ case MQ4 one?? it was funny and introduced me to COOJ
is it private or deleted??
thats gonna melt damn, the fan of the GPU its too close of the case wall, meaning that it has no space for the hot air to go up and exit the case
Nah, my case is way smaller than that(metalfish S3) the gpu run just fine, specially if you underpower it.
@@zaxmaxlax thats the problem, u cant get the full power out of it and it will more likely last less
@@Pepo.. ITX builds are always a compromise, you could also go for a nr200 and put a 3 slot GPU and that's fine too.
很喜欢这个机箱
搞自己呀 10多年前跟者眾籌買了第一代m1 爽得不得了
I'm in love with that little case!...but why the creator of the case choose a flex psu? 😔
That’s the only option I think
sfx not fit lol
If you want small then flex is more dense compared to sfx or especially atx form factor.
Take a look at Dan case~
全都高極貨的感覺,但顯卡呢?
每一秒都是金钱的味道
Top la vidéo et trop mimi 🥰 la config :)
想知道up用的电动螺丝刀是什么品牌型号~
at 2.48, why she is connecting that cable between graphic card and mainboard ?
It would've been a lot more satisfying if you used a Noctua L12S
Love the case, can you share what wifi antena model/type do you used?
could you find the name? I'm also interested in knowing
@@Chunpokomon u ever find it?
Why did you use that rubber foam thing.
其实那块蓝色压着cpu的是accessories？
Anyone know what monitor he was using by any chance?
Why does the processor's native latch not suit that it must be constantly changed to this piece of metal?
Nice case
电动螺丝刀是什么牌子的求推荐一下谢谢！！！
what screw size was used for the 15mm fan
開機真快
Name/Brand of the case please?
Can you give me the name of this case. Thanks!!!
What is the blue plate installed around the CPU called and what is its purpose?
CPU contact frame. it helps to secure the cput and provides even contacts
@@dgrain6636 Thank you!
impressive build ngl
這樣一套大約要多少呢？
2:49 А зачем видеокарту подключать в материнскую плату?
Видимо, чтобы подключить монитор через USB-C. Вроде видел когда-то такую схему.
1:08 at this point I'm thinking maybe she is going to do liquid nitrogen oc'd
电动螺丝起子是小米的吗？
还有塞不进东西的痛苦，亲身感受
and its expensive than regular size but video card cheaper.
Молодец девчонка.
不算显卡，以来多少成本？
螺絲起子 哪裡買的
Subbing just because you use mini electric screwdriver
快乐
You now you don't need that cable? You can just toggle preferable GPU in windows settings
装这套需要多少💰
方便問下裝在wifi天線位置的是什麼嗎？
謝謝
Да это же заглушки для вай-фая, с такой же резьбой, должны быть на Али экспресс)
扣子天线，淘宝一堆，十块钱不到，信号稍弱些。
所以 L9i 上面的海绵是为了建立风道么
什么品牌的电动螺丝刀
想知道螢幕是?
我为了省钱自己组一台itx主机搭携带式荧幕
机箱啥牌子？
为什么不直接买NUC🤔
當初我也訂MQ6 FlexATX電源都訂好了 無奈一直延遲發貨等了快三個月 最後還是找了能支援SFX的殼玩了
nihao
@@neins nihao
哈囉~請問你當初訂的時候是在官網訂還是淘寶訂的呢?
@@ewaitkimo 淘寶買的 官網印象中貴一些
what is the name of moniter ? thank you
2:34 hey what happened to the duct at 1:57 ?
and why would you have to connect thunderbolt to dp cable at 2:45 ? is there a reason?
[edit] those were for thunderbolt daisy chain configuration
hi, can you enlighten me on those DP to Thunderbolt? what does it for? and is it giving any benefits at all?
and for the end product (display on monitor), he would just plug into the other DP port, wouldnt he?
@@notme6254 it turned out to be configuring thunderbolt devices via daisy chain connection. in order to do that, eGPU'output is fed into motherboard's minidp(thunderbolt bypass port). then the monitor is connected to motherboard's USB-C thunderbolt connector, making motherboard the main source of thunderbold daisy chain connection.
you may find diagrams of that on MSI's MEG Z690 series manual. I found this info on MEG Z690 ACE manual on page 18.
@@e_sence thanks for the answer, i have look at MSI's MEG Z690 manual too and quite understand what it means about daisy-chain connection. so according to my understanding, can i say that the motherboard will act as dock/hub or something like that, just to get those bigger and faster transfer bandwidth for other devices that connect to the motherboard later? but for the monitor output, they still use the eGPU right? even though its connected to motherboard's Thunderbolt port?
@@notme6254 quite right. maunual says it can support multiple devices via daisy-chain function of thunderbolt including eGPU. but sending eGPU output in a thunderbolt lane needs some kind of "transfer station" at the motherboard's side, so the MiniDP passthrough port is needed to get eGPU's DP signal to turn into thunderbolt signal and sending that through thunderbolt USB-C connector.
@@e_sence ah i got it, so the Mini DP is the one as a bridge from eGPU to the monitor. thanks for the explanation!
散热可以换L9x65吧