Hello there, i fitted the belt new , set tensioner good rechecked twice all line upo and the timing belt sounds like its too tight , i bought belt from china no mitsubishi though , i have 2 vans and with the chinese belt makes noise at idle . but runs well any idea hoe to stop the noise ?
Thanks for the comments, try to check the tension of the timing belts, must be adjust to proper tension so that it will not create noise at Idle and during acceleration.
Nice video sir ..sir tanong lang nung pag balik lahat ok Naman andar kaso d na mag work RPM , tinanggal distributor binalik Ayun ok nanaman RPM display kaso Meron hadyong binaklas nanaman small belt balance adjust yun tension ok na wala na noise kaso pag balik lahat nawala nanaman RPM display hehe any advice sir? Tnks
Check and clean throttle valve and stepper motor sir baka madumi, then reprogram yung fixed sas ng servo kit gamit ang scan tool, thanks sir sana makatulong. GOD BLESS PO.
Sir double check nyo ung timing mark kung magtakapat lahat ng stationary at moving mark, at ung sitting ng balancer shaft lower side dapat nasa baba ung camlobes ng balancer shaft para wlang vibration especially during acceleration. Sana makatulong. Salamat po
@@autofixgarage5438 ok naman lahat ng timing sir, sakto lahat, napansin ko may tama ang crankshaft sensor sa isang side, yong sa plastic banda, yong may magnet ok naman, tumama kasi yong plate na umiikot sa gitna ng crankshaft sensor. May code sxa na camshaft sensor correlation. Nag request ako ng bagong crankshaft sensor, after 2days ikakabit ko, e update kita sir salamat
Thankyou sir. Very much appreciated from Australia
Your welcome sir, thank you too.God bless, be safe and healthy always.
Cuánto es su precio de un distribuidor de 4g64 ocupó uno me encuentro en México Ciudad Mexicali BC
Hello there, i fitted the belt new , set tensioner good rechecked twice all line upo and the timing belt sounds like its too tight , i bought belt from china no mitsubishi though , i have 2 vans and with the chinese belt makes noise at idle . but runs well any idea hoe to stop the noise ?
Thanks for the comments, try to check the tension of the timing belts, must be adjust to proper tension so that it will not create noise at Idle and during acceleration.
Nice video sir ..sir tanong lang nung pag balik lahat ok Naman andar kaso d na mag work RPM , tinanggal distributor binalik Ayun ok nanaman RPM display kaso Meron hadyong binaklas nanaman small belt balance adjust yun tension ok na wala na noise kaso pag balik lahat nawala nanaman RPM display hehe any advice sir? Tnks
Check and clean throttle valve and stepper motor sir baka madumi, then reprogram yung fixed sas ng servo kit gamit ang scan tool, thanks sir sana makatulong. GOD BLESS PO.
Sir ask ko lang, after namin nag palit ng timing belt, nag cu cut of ang makina after few.minutes. nag vibrate tapos namamatay sxa
Sir double check nyo ung timing mark kung magtakapat lahat ng stationary at moving mark, at ung sitting ng balancer shaft lower side dapat nasa baba ung camlobes ng balancer shaft para wlang vibration especially during acceleration. Sana makatulong. Salamat po
@@autofixgarage5438 ok naman lahat ng timing sir, sakto lahat, napansin ko may tama ang crankshaft sensor sa isang side, yong sa plastic banda, yong may magnet ok naman, tumama kasi yong plate na umiikot sa gitna ng crankshaft sensor. May code sxa na camshaft sensor correlation. Nag request ako ng bagong crankshaft sensor, after 2days ikakabit ko, e update kita sir salamat
@@franciscogerbolingo6188 okay, ingat lagi sir. God bless.
Try to do initialization in the system special function, if you have scanner.