Thank you so much for putting this video together. Helped me out no end. I would not have managed it without your help. FWIW (and to try and help any others that are following along), I ended up put the wiring out through the original hole (that the other tail lights come out of). Also, I had the Hayman Reese bar which seems to be absolutely identical (but has a flat 7 pin connector). I also had a bumper tab bar (shown at 8:27) I needed to be cut with an angle grinder before I put back on behind the plastic bumper. Last thing I had to do was re-trim the bumper as the tow ball was not 100% centred - also super glued the black trimming on to make sure it was secure. Final advice I have is that; for me the 'keyless system maintenance' light came on for a few days after installation, but seemed to be OK a couple of days later.
Well done. We were lucky got the later model sport and the bumper doesn't have to be cut. Also gives more room between ball and bumper, an added bonus.
I had inspected about 5 Pajero Sport for purchase and they are 2018+ so reasonably new. Why every single one has some underbody rust. I checked a Toyota fortuner 2018 today and it was totally clean. I like the look of the Pajero sport but it is a real let down. Does your Pajero Sport have any under body rust?
Read your manual in sensors section.. using the parking sensor off button you can press and hold for 3 seconds with in reverse. Changes from standard mode to towbar mode.
Nicely done mate. learn so much from this video. I want to fit one for mine.I found a website of Tow Bar Australia,www.towbarsaustralia.com.au/ is this the right one where you bought that towbar kit? Thankyou so much mate.
Thank you so much for putting this video together. Helped me out no end. I would not have managed it without your help.
FWIW (and to try and help any others that are following along), I ended up put the wiring out through the original hole (that the other tail lights come out of). Also, I had the Hayman Reese bar which seems to be absolutely identical (but has a flat 7 pin connector). I also had a bumper tab bar (shown at 8:27) I needed to be cut with an angle grinder before I put back on behind the plastic bumper. Last thing I had to do was re-trim the bumper as the tow ball was not 100% centred - also super glued the black trimming on to make sure it was secure. Final advice I have is that; for me the 'keyless system maintenance' light came on for a few days after installation, but seemed to be OK a couple of days later.
Excellent video, and much more informative than the instructions supplied with the towbar.
Your video was extremely helpful, unlike the instructions that come with the tow bar.
You have explained the installation very well, thanks so much for your advise.
Great insight on a towbar installation. Wouldn't mind having a go myself one day.
Well done. We were lucky got the later model sport and the bumper doesn't have to be cut. Also gives more room between ball and bumper, an added bonus.
Great job.
Awesome video!
Very professional & well explain video 👍
This video is very good help me so I really appreciate it thanks mate
Nice work! And that tow bar is awesome id like to have one
Well done.. thank you for sharing
Well done!! Thumbs up.
Hey, great video. When you attached the two bumper tabs onto the bar did your tek screws fit? Ours seem too small for the holes in the bar?
Sorry, I can't think which bit you're describing.
Mate I have exactly the same problem, looks like it's factory fault, I'm going to drill and tap the hole and use size up bolt, M8 I suppose.
Very well and perfect installation. Thanks for sharing. Please advise where we can order this tow bar. We have the same SUV.
nicely done ..
Great Job!
I had inspected about 5 Pajero Sport for purchase and they are 2018+ so reasonably new. Why every single one has some underbody rust. I checked a Toyota fortuner 2018 today and it was totally clean. I like the look of the Pajero sport but it is a real let down. Does your Pajero Sport have any under body rust?
Great video! I wonder is the pajero sport tow bar can fit onto a pajero exceed...
Was this just plug and play. I presuming the vehicle didn't need to be put on a computer to active? Cheers
😎😎😎
You from Manchester?
Nope, Nottingham!
I just got my one fitted, But central reverse sensor sometimes beeps. Do you have this issue?
Read your manual in sensors section.. using the parking sensor off button you can press and hold for 3 seconds with in reverse. Changes from standard mode to towbar mode.
@@bradleyqldsaladfarms6364 do u need to repeat this everytime or it will stand ever u change
@@leewenlong2008 as I understand it stays in mode once selected.. will be fitting my towbar in the coming weeks.
Nicely done mate. learn so much from this video. I want to fit one for mine.I found a website of Tow Bar Australia,www.towbarsaustralia.com.au/ is this the right one where you bought that towbar kit? Thankyou so much mate.
Hey, great video. When you attached the two bumper tabs onto the bar did your tek screws fit? Ours seem too small for the holes in the bar?
Which part of the vid are you referring to?