I had an etracer 6415N a long time ago. Cost a lot of money back then and it didn't last long. I think only a few months. Very disappointing. I hope this new one i bought well last longer. My main system uses an mpp solar PIP-5648MT.. i would buy victron but that's a bit overpriced for what one gets
Maybe you were just unlucky, there are many good reviews on you tube for this controller and thats the reason i bought them, serves me well and would buy them always if i need another
I just subscribed to your channel but I have a question I'm wanting to know how you connect to charge controllers that are EP ever 80 amps does automatic from 12v and up
It automatically detects the voltage. Its wise to connect the battery bank first. And watch it detect it. Once its detected 12v,24v ,36v or 48v then hook up your solar panels. Hope that helps. The 80a is a good unit.
I bought the WiFi E-box 1 for my EPEVER solar charge controller and the USB cable and I've had zero luck with either. I just can't establish communication no matter what settings I use. It's so frustrating and it just shouldn't be this difficult. The controller itself seems to work fine, I just can't establish communication to input my battery parameters.
Those wifi E Boxes are a waste of money. I have them but never really used them. They don't work that great and the information you gather from them is very limited.
Yesterday I could borrow an MT50 from someone and found out that one of my two mppt is not read by the MT50. I could access one mppt and program it in user setting, but the other one doesn't communicate with the module as so I can not read/write from the MT50 to/from the mppt. :-( Is there a way to reset this mppt TracerAN to reboot ?
The load is the right button. Just tap it and you will see the load light bulb icon look like its illuminated. Keep in mind the load is only designed to handle so much power.
Im not sure. Ive not tried to hook any of mine to a pc. I just use the interface display on one of these. I have 2 40amp tracer 4210an charge controllers going all the time. I should try to network them to a pc. I wanted a 100amp unit but i think since i have 4 different arrays this is better. Let us know if you figure out something. Thanks for posting
I dont remember but its in the manual. You can set it to power the load only under certain conditions or off under certain conditions. It can be set. And those abbreviations indicate that but without the manual infront of me I cant really tell you
You must not either. You watched it and still couldnt figure anything out except how to cry for negative attention. What do you want me to do? Make a better video for you? Im not a professional here buying houses off youtube . Ill point you in that direction. Go watch some of those guys channels not mine. Watch then review all the free gear they get and provide bias reviews of things so you buy stuff and make them $
Thanks, this is such a good controller, no issues for 7 years now, bought 2
I had an etracer 6415N a long time ago. Cost a lot of money back then and it didn't last long. I think only a few months. Very disappointing. I hope this new one i bought well last longer. My main system uses an mpp solar PIP-5648MT.. i would buy victron but that's a bit overpriced for what one gets
Maybe you were just unlucky, there are many good reviews on you tube for this controller and thats the reason i bought them, serves me well and would buy them always if i need another
I'm sure that's the case. I've had items that didn't work for others but worked for me. Bit of a lucky dip
شكرا لك اخي بارك الله فيك.. لكل فيديوهاتك.. وشكرا لإضافة الغه العربيه 🙏☺
I’m feeling dubious getting instructions from someone that doesn’t know 1:09 what lithium batteries are. 3:30 to be fair he did recover.
I'm not much help with lithium. I don't use them . Waiting on sodium ion batteries to hit the market
the screw are probably Power point which is similar to Phillips with the tip ground down
Probably
Thanks!
No problem!
Older EPever controllers will only work with older version mt-50 control boxes. Same with newer version controllers and Mt50s.
I just subscribed to your channel but I have a question I'm wanting to know how you connect to charge controllers that are EP ever 80 amps does automatic from 12v and up
It automatically detects the voltage. Its wise to connect the battery bank first. And watch it detect it. Once its detected 12v,24v ,36v or 48v then hook up your solar panels. Hope that helps. The 80a is a good unit.
I bought the WiFi E-box 1 for my EPEVER solar charge controller and the USB cable and I've had zero luck with either. I just can't establish communication no matter what settings I use. It's so frustrating and it just shouldn't be this difficult. The controller itself seems to work fine, I just can't establish communication to input my battery parameters.
Something isn't right. Send it back
Those wifi E Boxes are a waste of money. I have them but never really used them. They don't work that great and the information you gather from them is very limited.
I have a BT adapter and utilize their app to configure it, etc ; no need for the MT 50 with the app
Do to external controller. Plug mines in and it just showing “connecting.”
Something isnt right. Try a different ethernet cable
Yesterday I could borrow an MT50 from someone and found out that one of my two mppt is not read by the MT50.
I could access one mppt and program it in user setting, but the other one doesn't communicate with the module as so I can not read/write from the MT50 to/from the mppt. :-(
Is there a way to reset this mppt TracerAN to reboot ?
Im not sure. If its not real old i would contact eppever
Is there there a way to setup the controller only without the mt-50 remote. I cant seem to get the load to come on.
The load is the right button. Just tap it and you will see the load light bulb icon look like its illuminated. Keep in mind the load is only designed to handle so much power.
I can't get the rs485 connection to work with windows 11.. i think the login battery presets are actually ok
Im not sure. Ive not tried to hook any of mine to a pc. I just use the interface display on one of these. I have 2 40amp tracer 4210an charge controllers going all the time. I should try to network them to a pc. I wanted a 100amp unit but i think since i have 4 different arrays this is better. Let us know if you figure out something. Thanks for posting
I just ordered the mt50. I can't be bothered with windows 11
@herbertvonsauerkrautunterh2513 probably the best thing to do
What does load types 117 and 2n means, anyone pls??
I dont remember but its in the manual. You can set it to power the load only under certain conditions or off under certain conditions. It can be set. And those abbreviations indicate that but without the manual infront of me I cant really tell you
Can anyone understand this?
Nope 🙅♂️ 🙅♀️ lol 😆
Sure would have been nice if you knew what the heck you were doing.
You must not either. You watched it and still couldnt figure anything out except how to cry for negative attention. What do you want me to do? Make a better video for you? Im not a professional here buying houses off youtube . Ill point you in that direction. Go watch some of those guys channels not mine. Watch then review all the free gear they get and provide bias reviews of things so you buy stuff and make them $