You just helped me out thank you brother! You wouldn't believe how many of these videos are of someone fumbling about not teaching you anything. I hit your bell to show appreciation
He is just fumbling around if you hadn't noticed. He didn't clearly explain what he was doing, why he was doing it and then couldn't explain how to properly finish it. He didn't really fix the jack, just a symptom of the problem, and then had no idea how to properly refill much less bleed the jack.
Had the exact same problem with my old Craftsman jack! It would lift my Duster and my wife's Mazda 3 just fine. But, it would weeze and give up trying to pick up one wheel of my 3/4 ton truck. I kept trying to fill it through the screw in the back. Seems to work much better now, the test will be when I try to pick up my 3/4 ton in the morning! Thanks for making this video!
Just wanted to say thank you for your videos. I have been trying to figure out how to service mine that's kinda like yours and this video was exactly it. Even after "regular" bleeding, I was only getting about 6 inches of lift out of it and it looked like the fluid was completely full. Found the rubber plug, pulled it and sure enough, took a bunch of fluid. Bled the bubbles out of it and now the thing works like brand new. I appreciate you taking the time to put this video together!
If I could do it over, I'd shoot one video. I learned quite a bit between shooting the videos (and some even after). Glad you were able to see both. The jack is working like it is brand new still and that video was shot almost a year ago.
Thank you for the video. I have 2 floor jacks that need repaired. One just started leaking at the same place and I was wondering if it just needed a o ring replacement. The other one needs a different kinda repair but I'm not planning on digging into it until later.
That rubber push in plug is the fill point on most all floor jacks,,,you see air bubbels because the fluid is low,,,,FILL IT UP !! LOL !! The fill plug is allways at the high point .
I liked your video too. I have two 3 ton jacks that were destined for recycle,and had tried to repair it,but also had no idea that you had to bleed them, I was able to fill them but they were never bled. All my 3 ton jacks are similar and the O ring looks to be the same size.Thanks
Liked your video. I have a similar model and need to work on it soon.. I do not believe that rubber cap is a bleed valve. It is just a fill point for adding fluid. More than likely you were not getting a good bleed from the normal bleed point because your fluid was so low.
You're probably right. It's just bizarre that it is not mentioned at all in the owner's manual, and honestly I've owned that jack a long time and never noticed that spot. I was about to throw away the jack believe it or not! Now it works like brand new!!!
your vid is much better than the first one I watched where the guy says remove the rubber seal top off the hydraulic fluid replace rubber cap then pump up four or five times & remove the cap to release the air. well after filling & replacing cap on the very first pump it blew the rubber cap off & hydraulic fluid shot out everywhere! it ruined my clothes, hat , got in my eyes. the dude should remove his video it isn't clear & way off the mark on how to properly bleed the jack. I give your vid a thumbs up.
hey this is cool i have that same "SEARS CRAFTSMAN"jack an i me and my buddy purchased them in 1992 my buddy wore out his wheels and they do not sell them anymore,...but my jack has the same it only raises about a quarter of the full height.thanx for the info.
If you look at the comments on my other jack video, someone posted a link where they say you can buy restoration parts. I don't know if they sell the wheels there but you might get lucky. Good luck!
I wanted to see how you got that rubber plug back in. I have a 3 ton Sears Craftsman floor jack that is identical to yours and it is a total pain in the ass getting that plug back in.
Mine was a pain too. I basically use a small flat tip screwdriver and wedge it in around until Im able to get it in. I typically spend 5-10 min. It takes forever but you will get it if you take your time. A pair of needlenose pliers will hold it in place so you will have more space to work the small screwdriver.
Did you have the handle turned counterclockwise when you were pumping it. I don't know I have a new Jack but I didn't pick it up yet but the instructions say to open the valve and pump it and then push the rubber plug to the side a little bit would it matter if I did that or should I just remove the rubber plug and pump it with the handle open with the release valve open in other words?
This video was pretty decent help, except my jack still wouldn't go up past 5 or so inches and it's a brand new floor jack (cheapo) from Walmart. Folks need to beware: These $24.99 jacks come with a case and the handle but have almost NO hydraulic oil in them. SO I followed your advice here and it took forever to get that stupid jack to start going up, but then it still wouldn't go the full 13 like it says on the box. Folks, there is an orange cap on the back of the piston (mine says do not adjust). There is a flat tip screw under that cap, and if you adjust it be sure to only do it in increments of 1/4 turn each time. I found that all my jack needed was to adjust that screw a little bit after I topped it off with hydraulic oil. Now it works the way it should have worked right out of the box These companies making these things are without a doubt doing them this way to make more money off of us consumers because I had to buy the oil as well and then spend nearly 2 hours playing with the stupid thing to get it to work. I do NOT recommend this product to anyone and I have purchased many jacks in lifetime but NEVER ran into this. So beware. A word of caution: if you do adjust that screw and your jack gets ruined don't look at me to take the blame. That's on you for doing it. In my case if the jack was ruined I'd be out all of $30. LOL.
on mine counter clockwise opens it and clockwise closes it. By "open" I mean that pumping the jack will not make the jack lift. "Closed" means pumping it will raise the jack (assuming the jack is functional!)
My jack is exactly like that one. I bought new probably in the 80's and haven't used for 20 yrs. It wouldn't lift all the way. If you pull the big shaft where the grease zerk is you can move the lift portion away from handle to make it much easier to access rubber fill plug. I also used a syringe to easily fill with jack oil without a mess. Most rubber plugs are not located on top as there needs to have some air space to work right, IMO. Don't lose or damage plug cause you'll have a tough time finding one. Just push in and work it in hole with dull screwdriver. Just fixed mine yesterday by adding oil and it works perfectly again. Great video, Thanks.
i have the same jack and i foudet mani nears and an satesfait weth it i founded in the garbich ind blieeded agen is liking thank you for the heats up on haw to blireded. i file loky to the years of use
That appears to be the same jack as my Allied Indy 5 jack (2003 from Harbor Freight). The cylinder fill plug IS mentioned in this manual: www.hcrcnow.com/uploads/drawings/ch4172.pdf
apparently it is mentioned in some manuals, but I didn't find that out until after the video was published. If I could do it all over again I'd make one video fixing the o-ring and filling and bleeding the jack.
My problem is my jack wont go down. I weigh 236 and have to put all my weight on it to come down. But most of the time I cant get enough weight on it while it's under the car.
I have the same jack, what is the info on it, name, manufacturer, size? I see the sticker came off of yours just like mine, your videos are a big help...
What if you can't close the valve "tight" anymore?? Is it time for a new jack?? I can "close" it, it will lift the car up, but it won't "stay", it will bleed down and lower over 30 minutes or so. The jack is at least 25 years old.
Did you watch my o-ring replacement video? czcams.com/video/pe7NY1Nh6sQ/video.html My jack was slowly lowering via a leak at the o-ring. As far as not being able to fully tighten the valve, I don't know for sure, seems like it could be a lot of things - something physically blocking it, a worn o-ring or similar, or a piece broken off somewhere. Hopefully someone on here will have an answer for you.
I figured it out. I removed the valve, then reinstalled it. I think that the threads were loose and even though the teeth were turning, the square fitting on the bottom wasn't engaging the valve. I topped off the jack fluid, it works fine now.
Do you know who the manufacturer of the jack is? Or what the model is called? I have exactly the same, but I cant find any information about this. Greetings from Germany
I don't think my cheap Torins have the second bleeder. Or at least I did not see one. It is very hard to purge air and add fluid without a 2nd one. I must have added about half a quart of fluid so far..
+W & J's Handy Dad I read through the Torin Black Jack manuals (for both 2 ton and 2.5 ton). I have 8 of them to fix. The fact that no fluids are leaking out is good. The manual states all of the things nobody has ever mentioned online. "IMPORTANT: BEFORE FIRST USE on any hydraulic jack perform the instructed air purge procedure to remove any air that may have been introduced as a result of product shipping/handling." So here's what I did. Loosen the jack release valve. Pump the handle 8 times. Tighten the release valve. Extend the ram to the highest position. There's a rubber grommet on the ram that looks just like a metal rivet but it's actually just metallic paint. Squeeze this gently with a pliers and this relieves the air pressure. Repeat this method. According to Torin, the only reason for removing the oil fill plug is to add or check the oil level. To check the oil level on the ram, apparently the jack needs to sit vertical, handle down, so the ram is facing upward. The oil level in the fill plug should be visible.
@@markfothebeast Sounds good, except for, placing the jack vertical. I don't know how I would do that? I didn't pick up my jack yet from Menards, but I know it's over 100lbs. www.menards.com/main/tools/automotive/automotive-tools-shop-equipment/masterforce-trade-3-ton-heavy-duty-floor-jack/t830008/p-1555569041912.htm
Finally figured it out ? It only took you 5 years ...good show🤣🤣!!
You just helped me out thank you brother! You wouldn't believe how many of these videos are of someone fumbling about not teaching you anything. I hit your bell to show appreciation
glad it helped you!!
He is just fumbling around if you hadn't noticed. He didn't clearly explain what he was doing, why he was doing it and then couldn't explain how to properly finish it. He didn't really fix the jack, just a symptom of the problem, and then had no idea how to properly refill much less bleed the jack.
Had the exact same problem with my old Craftsman jack! It would lift my Duster and my wife's Mazda 3 just fine. But, it would weeze and give up trying to pick up one wheel of my 3/4 ton truck. I kept trying to fill it through the screw in the back. Seems to work much better now, the test will be when I try to pick up my 3/4 ton in the morning! Thanks for making this video!
Just wanted to say thank you for your videos. I have been trying to figure out how to service mine that's kinda like yours and this video was exactly it. Even after "regular" bleeding, I was only getting about 6 inches of lift out of it and it looked like the fluid was completely full. Found the rubber plug, pulled it and sure enough, took a bunch of fluid. Bled the bubbles out of it and now the thing works like brand new. I appreciate you taking the time to put this video together!
Glad it helped you... I was about to throw away my jack and buy a new one
Thank you for sharing your experience
That rubber stop is the one I use ..26 years for fill maybe 3 times . Use it daily ..
You still have the owner's manual..!!!??? Kudos!!!
Thanks for the shout. Glad it's working.
Thank You for sharing.. Best to you and yours.
Thank You fo sharing.
Thanks for posting both videos on the floor jack. I'm getting ready to try my own repair.
If I could do it over, I'd shoot one video. I learned quite a bit between shooting the videos (and some even after). Glad you were able to see both. The jack is working like it is brand new still and that video was shot almost a year ago.
Thank you for the video. I have 2 floor jacks that need repaired. One just started leaking at the same place and I was wondering if it just needed a o ring replacement. The other one needs a different kinda repair but I'm not planning on digging into it until later.
Very good videos finally i fixed my cornwell jack .thanx alot ...
That rubber push in plug is the fill point on most all floor jacks,,,you see air bubbels because the fluid is low,,,,FILL IT UP !! LOL !! The fill plug is allways at the high point .
"BUBBLES"
I liked your video too. I have two 3 ton jacks that were destined for recycle,and had tried to repair it,but also had no idea that you had to bleed them, I was able to fill them but they were never bled. All my 3 ton jacks are similar and the O ring looks to be the same size.Thanks
Glad the videos were helpful!
Liked your video. I have a similar model and need to work on it soon.. I do not believe that rubber cap is a bleed valve. It is just a fill point for adding fluid. More than likely you were not getting a good bleed from the normal bleed point because your fluid was so low.
You're probably right. It's just bizarre that it is not mentioned at all in the owner's manual, and honestly I've owned that jack a long time and never noticed that spot. I was about to throw away the jack believe it or not! Now it works like brand new!!!
I do believe that the rubber oil plug removal helps to remove the air from the jack.
Ron Gerlach ]p]p]pppplppp
@@gaillittle6807 someone above mentioned a regular bleeder screw I don't believe there is a regular bleeder screw
your vid is much better than the first one I watched where the guy says remove the rubber seal top off the hydraulic fluid replace rubber cap then pump up four or five times & remove the cap to release the air. well after filling & replacing cap on the very first pump it blew the rubber cap off & hydraulic fluid shot out everywhere! it ruined my clothes, hat , got in my eyes. the dude should remove his video it isn't clear & way off the mark on how to properly bleed the jack. I give your vid a thumbs up.
thank you
I did the same thing:-(
dad has the same one helped him fix it thank to the video 5 stars!!
I apreciate a lot your help. Thanks a lot. Best regards from México
thank you so much for the vid i have the same jack thought i had to buy a new 1 the juck is working like new
I watch both viedios......helps a lot thank you
hopefully you got your jack fixed... I noticed you commented on the slowly lowering jack... this jack was doing that before I noticed the fluid leaks
Yes! Thankyou!
Just what I needed to know. Thanks for the vidio. It really was a big help.
should be called :
The final pumpdown :)
hey this is cool i have that same "SEARS CRAFTSMAN"jack an i me and my buddy purchased them in 1992 my buddy wore out his wheels and they do not sell them anymore,...but my jack has the same it only raises about a quarter of the full height.thanx for the info.
If you look at the comments on my other jack video, someone posted a link where they say you can buy restoration parts. I don't know if they sell the wheels there but you might get lucky. Good luck!
WJ Handy Dad hey bud thanks a million,i have my jack back to working 100%.also tganks for the info.great link.
Thank you THAT help me alot
I wanted to see how you got that rubber plug back in. I have a 3 ton Sears Craftsman floor jack that is identical to yours and it is a total pain in the ass getting that plug back in.
mine wasn't a problem as I recall.
Mine was a pain too. I basically use a small flat tip screwdriver and wedge it in around until Im able to get it in. I typically spend 5-10 min. It takes forever but you will get it if you take your time. A pair of needlenose pliers will hold it in place so you will have more space to work the small screwdriver.
good job
Did you have the handle turned counterclockwise when you were pumping it.
I don't know I have a new Jack but I didn't pick it up yet but the instructions say to open the valve and pump it and then push the rubber plug to the side a little bit would it matter if I did that or should I just remove the rubber plug and pump it with the handle open with the release valve open in other words?
That's the fill hole. And those things are a pain in the ass to get out and *put back in*.
Definitely
This video was pretty decent help, except my jack still wouldn't go up past 5 or so inches and it's a brand new floor jack (cheapo) from Walmart. Folks need to beware: These $24.99 jacks come with a case and the handle but have almost NO hydraulic oil in them. SO I followed your advice here and it took forever to get that stupid jack to start going up, but then it still wouldn't go the full 13 like it says on the box. Folks, there is an orange cap on the back of the piston (mine says do not adjust). There is a flat tip screw under that cap, and if you adjust it be sure to only do it in increments of 1/4 turn each time. I found that all my jack needed was to adjust that screw a little bit after I topped it off with hydraulic oil. Now it works the way it should have worked right out of the box These companies making these things are without a doubt doing them this way to make more money off of us consumers because I had to buy the oil as well and then spend nearly 2 hours playing with the stupid thing to get it to work. I do NOT recommend this product to anyone and I have purchased many jacks in lifetime but NEVER ran into this. So beware. A word of caution: if you do adjust that screw and your jack gets ruined don't look at me to take the blame. That's on you for doing it. In my case if the jack was ruined I'd be out all of $30. LOL.
Which direction do you turn for the valve to be open
on mine counter clockwise opens it and clockwise closes it. By "open" I mean that pumping the jack will not make the jack lift. "Closed" means pumping it will raise the jack (assuming the jack is functional!)
My jack is exactly like that one. I bought new probably in the 80's and haven't used for 20 yrs. It wouldn't lift all the way. If you pull the big shaft where the grease zerk is you can move the lift portion away from handle to make it much easier to access rubber fill plug. I also used a syringe to easily fill with jack oil without a mess. Most rubber plugs are not located on top as there needs to have some air space to work right, IMO. Don't lose or damage plug cause you'll have a tough time finding one. Just push in and work it in hole with dull screwdriver. Just fixed mine yesterday by adding oil and it works perfectly again. Great video, Thanks.
@@jefffrayer8238 thank you for sharing
The hardest part is getting that damn rubber plug back in which you didn't show !
push in one side with your fingers, then tuck the other side with a blunt object like a small screwdriver
@@WJHandyDad Thanks so much for your response, this is where I was getting stuck too.
i have the same jack and i foudet mani nears and an satesfait weth it i founded in the garbich ind blieeded agen is liking thank you for the heats up on haw to blireded. i file loky to the years of use
What bleed. When the rubber plug was removed you could see it was low on oil.
Yes it's the plug but I still think you might have to bleed it.
That appears to be the same jack as my Allied Indy 5 jack (2003 from Harbor Freight). The cylinder fill plug IS mentioned in this manual:
www.hcrcnow.com/uploads/drawings/ch4172.pdf
apparently it is mentioned in some manuals, but I didn't find that out until after the video was published. If I could do it all over again I'd make one video fixing the o-ring and filling and bleeding the jack.
Michael Cox f
My problem is my jack wont go down. I weigh 236 and have to put all my weight on it to come down. But most of the time I cant get enough weight on it while it's under the car.
sorry, I haven't encountered that problem so I don't have any suggestions. Hopefully one of the viewers will.
Ok I can not get the release valve [ the thing with gear ] off at all how can I do this
Another video with hand in the way
I have the same jack, what is the info on it, name, manufacturer, size? I see the sticker came off of yours just like mine, your videos are a big help...
Sears 3 ton model # 875.501152 - also was marketed under other names from what I've been told
What if you can't close the valve "tight" anymore?? Is it time for a new jack?? I can "close" it, it will lift the car up, but it won't "stay", it will bleed down and lower over 30 minutes or so. The jack is at least 25 years old.
Did you watch my o-ring replacement video? czcams.com/video/pe7NY1Nh6sQ/video.html My jack was slowly lowering via a leak at the o-ring. As far as not being able to fully tighten the valve, I don't know for sure, seems like it could be a lot of things - something physically blocking it, a worn o-ring or similar, or a piece broken off somewhere. Hopefully someone on here will have an answer for you.
I figured it out. I removed the valve, then reinstalled it. I think that the threads were loose and even though the teeth were turning, the square fitting on the bottom wasn't engaging the valve. I topped off the jack fluid, it works fine now.
Awesome!!
The handle will not turn open or closed
I don't have an answer... wish I did. good luck!
Busco tutoriales en CZcams
Do you know who the manufacturer of the jack is? Or what the model is called? I have exactly the same, but I cant find any information about this. Greetings from Germany
Craftsman model 875.501152
@@WJHandyDad great, thank you!
what is the make and model of your jack. I have the same exact one but i cant find any indicators of its make or model.
Sears model 875.501152 jack, I think I purchased it around 1995.
Mine is a craftsman 9-50115 and looks exactly the same in this video.
How much oil do you add - when do you when to stop. I know you kept getting air - adding/bleeding but do you just top it off ? Thanks for the video.
basically until it was "full." It seemed to tell me when it was full and it started working perfectly. Sorry I don't have a more precise answer.
I don't think my cheap Torins have the second bleeder. Or at least I did not see one. It is very hard to purge air and add fluid without a 2nd one. I must have added about half a quart of fluid so far..
I thought about this after I filmed this video... have you tried filling it with the fill hole elevated? I keep wondering if that would work.
+W & J's Handy Dad I read through the Torin Black Jack manuals (for both 2 ton and 2.5 ton). I have 8 of them to fix. The fact that no fluids are leaking out is good.
The manual states all of the things nobody has ever mentioned online. "IMPORTANT: BEFORE FIRST USE on any hydraulic jack perform the instructed air purge procedure to remove any air that may have been introduced as a result of product shipping/handling."
So here's what I did. Loosen the jack release valve. Pump the handle 8 times. Tighten the release valve. Extend the ram to the highest position. There's a rubber grommet on the ram that looks just like a metal rivet but it's actually just metallic paint. Squeeze this gently with a pliers and this relieves the air pressure. Repeat this method.
According to Torin, the only reason for removing the oil fill plug is to add or check the oil level.
To check the oil level on the ram, apparently the jack needs to sit vertical, handle down, so the ram is facing upward. The oil level in the fill plug should be visible.
@@markfothebeast
Sounds good, except for, placing the jack vertical.
I don't know how I would do that?
I didn't pick up my jack yet from Menards,
but I know it's over 100lbs.
www.menards.com/main/tools/automotive/automotive-tools-shop-equipment/masterforce-trade-3-ton-heavy-duty-floor-jack/t830008/p-1555569041912.htm
Omitted putting the cap back on. You know it was a b*tch. lol
شنو نوع الزيت
HI where can I get the O ring what is the part #
I have that info in the video where I replace the o-ring, the link is above in the description of this video and there is a link in this video.
Thank you I found the info.
i got my o ring from napa
كم الكميه
Donde los orings
esta aqui... amzn.to/2iUhZHt
That would not be it!!!! Just your hand and handle would blow that rubber cap off!!!! Wrong side! Best you watch other vids on same topics! Bye
Not sure what you are getting at, but the jack works like brand new still... had no problems since I removed that rubber cap and refilled and bled it.
i missed the "how to" part. Zero verbal instruction.