Good afternoon How do you feel about new technologies that are not similar to the current ones, based on a completely new principle of burning any fuel with clean emissions into the atmosphere?
you all prolly dont care but does anybody know of a way to get back into an instagram account..? I somehow lost the account password. I love any help you can give me!
@Skylar Kendrick Thanks so much for your reply. I got to the site through google and I'm trying it out now. Seems to take quite some time so I will get back to you later when my account password hopefully is recovered.
I think 20 seconds is not enough in case of globe valves operation. They take time for full operation (full open or full close) and ball valves are not installed on the said circuit. Also in the case of globe valves, valves operating positions are not given in the video. Partial opening of the valve shall decrease the valve seat life. Curious, what to do?? 🧐🧐
1. If you have an installation with valves that may require more than 20 seconds to manipulate, you may have to exceed the recommended 20 second duration described in our procedure. However, the duration should be kept to a minimum amount of time. Our procedure is a guideline offered to assist operators with the majority of typical installations. 2. Valve position is important to the operator. A trained operator should be educated on the valves in their particular boiler installations. Otherwise, they should seek guidance from the valve manufacturer. We thank you for your comments. If you have any other questions, feel free to email us at askus@clark-reliance.com.
When blowing down of steam is done after 20sec and the drain valve is closed. Upon opening the the water valve to read the level in the boiler, will the water overcome the steam pressure?
No, the water level will promptly equalize with the level in the drum, because the steam piping ventilates back to the drum. The water level should stabilize very quickly, unless there is a blockage in the piping or the isolation valves are not fully opened.
Electric heating, inductive and resistive, is more energy efficient than natural gas and is used in water heaters and furnaces in a lot of places. However natural gas is cheaper per kWh and so it is still the most common energy source for heating because of that.
Hello Michael, we would be happy to discuss your application and best practices for extending the life of your equipment. Can you provide your city, state, and email?
Excellent way to describe blowdown procedure
Very clear and concise on how to do a blowdown!
Good afternoon How do you feel about new technologies that are not similar to the current ones, based on a completely new principle of burning any fuel with clean emissions into the atmosphere?
Thanks this was very useful.
Thank you
Great video, thanks.
Very good information to you dear sir, thank you
Rice milli faire tube boiler videos
Thank you so much for valuable information
Very nice level glasses
Good explanation
Thanks a lot.
very use full thanks a lot
Perfect
Now I know how to properly blowdown the sight glass
you all prolly dont care but does anybody know of a way to get back into an instagram account..?
I somehow lost the account password. I love any help you can give me!
@Shawn Israel instablaster ;)
@Skylar Kendrick Thanks so much for your reply. I got to the site through google and I'm trying it out now.
Seems to take quite some time so I will get back to you later when my account password hopefully is recovered.
@Skylar Kendrick it did the trick and I now got access to my account again. I'm so happy:D
Thanks so much you saved my account :D
@Shawn Israel Happy to help xD
Very nice sir
How to i know pipe is partially clogged
I think 20 seconds is not enough in case of globe valves operation. They take time for full operation (full open or full close) and ball valves are not installed on the said circuit. Also in the case of globe valves, valves operating positions are not given in the video. Partial opening of the valve shall decrease the valve seat life.
Curious, what to do?? 🧐🧐
1. If you have an installation with valves that may require more than 20 seconds to manipulate, you may have to exceed the recommended 20 second duration described in our procedure. However, the duration should be kept to a minimum amount of time. Our procedure is a guideline offered to assist operators with the majority of typical installations.
2. Valve position is important to the operator. A trained operator should be educated on the valves in their particular boiler installations. Otherwise, they should seek guidance from the valve manufacturer.
We thank you for your comments.
If you have any other questions, feel free to email us at askus@clark-reliance.com.
@@ClarkReliance thanks Sir
❤nic job
Excelent....water tiub
good and excelent
When blowing down of steam is done after 20sec and the drain valve is closed. Upon opening the the water valve to read the level in the boiler, will the water overcome the steam pressure?
No, the water level will promptly equalize with the level in the drum, because the steam piping ventilates back to the drum. The water level should stabilize very quickly, unless there is a blockage in the piping or the isolation valves are not fully opened.
nice lecture
Videos on navian non 240
Tq sir
Tq
Some makers recommend cross blowing
Many operators in some plants never blow down level indicator piping on the dearaetor and condensate tanks.
Any idea bruh..why some of them did not blow down the lvl.indic..
@@SeaMarinerosVlog They may be worried about tripping the feed water pumps as most they are connected to a low water switch.
Neat and clean in simple words explanation thanks
he forgets to mention any bypass button well doing it so you do not trip. we do a daily pm for insurance purposes @@danq.5140
Why not make a heater for personal home owners that use induction tehcnology to heat the water?! Then the jome! This is a multi million $ idea!
Electric heating, inductive and resistive, is more energy efficient than natural gas and is used in water heaters and furnaces in a lot of places. However natural gas is cheaper per kWh and so it is still the most common energy source for heating because of that.
My plant blows down every shift, every day.
Hello Michael, we would be happy to discuss your application and best practices for extending the life of your equipment. Can you provide your city, state, and email?
What are the odds these days of actually blowing a boiler up?
Need vedoi for steam turbine reduction gear element...
Traducir
Sight glasses
Ok