Magandang gabi brod. Baka matulongan m ako truble shot itong tinatrabaho makina sa man cla 18_280 mag overheat. Akin na ito top overhaul. Pinalitan ko na ito linner, piston ring cylender head gasket. Nozzul tip. Bagong calebret ang injection pump.umaandar na. Pagkatapos palyado. Mag overheat. Dati overheat ang problema nito.
Ano ang injection pump nyan sir?rotary ba or inline.sa ppagkakatanda ko kapag rotary injection pump.35degress btdc ang injection timing.kung inline nman ay 13 degrees
Nakalimutan ko sir nandon kc sa record book ko.pero pakisearch din po sa google baka meron yan.sa pagkakatanda ko.yong main bearing ay 300nm plus 90 degrees.conrod bearing 100nm plus 90 degrees at cylinder head 300nm plus 90 plus 90.
please make a 30 minutes explanation video on adjusting valves, tdc, ebs and the logic. please please . even if you dont film at the truck, oits ok if you flm in front of a drawing board and explain why TDC and all the rest. what means running mate etc . thank you . make a video so that alll normal DIY truck owners should understand . it will be the most amazing video i assure you .
Boss matanong ko lng boss ano ba iyung dapat gawin boss pag ang man tgm 18.240 nag indicate sa cluster nang "check fuel supply" sana mapansin boss salamat
...boss pwd malaman kung anong dapat gawin...nakalagay sa dash board ...malfunction on board computer...tas ayaw na nya mag matic magagamit mo as a manual nlng...salamat boss...
Good morning sir I am facing a problem with D2676 MAN eingen. There is creating pressure in readiator i changed readiator and air Compressor pump but problem is still as it is . Please help
Actually that was also happened here.creating pressure even radiator and air compressor are new.so we was dismantled the head and check the liner and clean.the after that,pressure is gone
Thank you bro ... God bless you
You're welcome brother
Magandang gabi brod. Baka matulongan m ako truble shot itong tinatrabaho makina sa man cla 18_280 mag overheat. Akin na ito top overhaul. Pinalitan ko na ito linner, piston ring cylender head gasket. Nozzul tip. Bagong calebret ang injection pump.umaandar na. Pagkatapos palyado. Mag overheat. Dati overheat ang problema nito.
Saan location mo sir?
Ano ang injection pump nyan sir?rotary ba or inline.sa ppagkakatanda ko kapag rotary injection pump.35degress btdc ang injection timing.kung inline nman ay 13 degrees
Thank you 👍
Respct to you comrade!...
Thank you Sir
Sending full support from san vicente cam norte...pashout po lods
Cge padi d lang kc nakakagawa pa ng bagong video.salamat
Informative and helpful
Salamat manoy
wow galing talaga hehe
Hahahahha tsamba lang
How much clearance you fixed
Where is your workshop
I have issue in eletrical malfunction, ENGINE RPM lever is not working, what was issue may be
Good pm bro anong max and min torque sa cylinder head d2066 /con rod at main bearing
Nakalimutan ko sir nandon kc sa record book ko.pero pakisearch din po sa google baka meron yan.sa pagkakatanda ko.yong main bearing ay 300nm plus 90 degrees.conrod bearing 100nm plus 90 degrees at cylinder head 300nm plus 90 plus 90.
Hello brother i want to my vehicle where is your workshop
Hello. Why you must make first EVB 0 clearance to adjust exhaust valve?
Hi sir,to get an accurate adjustment and clearance.
❤🎉 thanks 🙏
I have issue mantruck
Model 2015, - 385
please make a 30 minutes explanation video on adjusting valves, tdc, ebs and the logic. please please . even if you dont film at the truck, oits ok if you flm in front of a drawing board and explain why TDC and all the rest. what means running mate etc . thank you . make a video so that alll normal DIY truck owners should understand . it will be the most amazing video i assure you .
Boss matanong ko lng boss ano ba iyung dapat gawin boss pag ang man tgm 18.240 nag indicate sa cluster nang "check fuel supply" sana mapansin boss salamat
Galing ser salamat sa pagshare done watching like subscribe done
Good job sir . Saan Po kayo sa saudi Po .Anong company Po??
Dito ako sir sa al kharj
...boss pwd malaman kung anong dapat gawin...nakalagay sa dash board ...malfunction on board computer...tas ayaw na nya mag matic magagamit mo as a manual nlng...salamat boss...
@@charlitoautor8243 sensya na po sir d kita nareplayan agad ok na po ba yong unit nyo?
Thank sir
❤
How are you
Hello sir,,Although the letter N does not appear, the engine is running... Please what is the reason
Hi sir,actually i cannot experience that kind of trouble yet,but i want to know if when you shift in reverse,letter R showing?
And hows if you shift in first gear or second gear third gear.number is showing or not?
yes sir it shows the number R....and everything is fine..
Good morning sir
I am facing a problem with D2676 MAN eingen.
There is creating pressure in readiator i changed readiator and air Compressor pump but problem is still as it is .
Please help
Hi sir.what kind of cylinder head that one sir?is that single inline cylinder head or indibidual?
Actually that was also happened here.creating pressure even radiator and air compressor are new.so we was dismantled the head and check the liner and clean.the after that,pressure is gone
Singl head
Make a vedio we will thankful to you
Clean liner you means Piston liner or water lines
Shot out paps
Sir ilan poh valve clearance in / ex
Nasa video po sir.
Intake--0.5mm
Exhaust--0.8mm
Evb--0.6mm
Hi
Hu
Hi