Is the G90 dent tool worth purchasing?

Is the G90 dent tool worth purchasing?
In this episode I take a look at the G90e dent puller tool. I demonstrate how it works a give you my opinion on the effectiveness of this tool . Enjoy the video! SUBSCRIBING AND HIT THAT BELL for notifications of my latest videos!
To increase your knowledge and build your skill SUBSCRIBE to the channel and check out my other videos!!!
Disclaimer as an Amazon Associate I earn a small commission (at no additional cost to you) from qualified purchases. I will not recommend any product that I do not use personally.
Amazon links to products i use:
⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️
G90e dent tool operats on 110
amzn.to/3bWvjqe
Astro euro HE paint gun
amzn.to/2RcxgFm
automotive masking plastic
amzn.to/2FqPmk7
masking machine
amzn.to/2RdjS3S
air angle grinder
amzn.to/2Rcgia0
12 inch masking paper
amzn.to/3m4JNsB
3/4 3m yellow making tape
amzn.to/3bMkmYe
2k Aerosol clear ooat
amzn.to/3bMkhUq
upol clearcoat kit
amzn.to/3m5G7qD
spot putty
amzn.to/32eOwQF
Aerosol guide coat
amzn.to/3ifMx47
Grinding disks
amzn.to/2FdWeBO
Mirka Abrasives Mirlon Total 4.5" X 9" Scuff Pads, Ultra Fine (1500 Grit)
amzn.to/2D6OKiO
sanding block
amzn.to/3aMpxqw
80 grit sandpaper
amzn.to/3jjmlWz
3m 180 grit sandpaper
amzn.to/34mpK2t
3m 320 sandpaper
amzn.to/2Qft6ft
Speedokote SS-2790G-Q/SS-2790A-8 Super Fill High Build Primer Gray
amzn.to/2Y9mnbb
Bondo Gray Filler Primer, Highly Durable & Easy to Use, 11 oz, 1 Aerosol
amzn.to/3flt1Rm
Kleanstrip Prep-All Wax & Grease Remover, Gallon (KLE-GSW362)
amzn.to/30nRBwV
To increase your knowledge and build your skill check out my other how to videos and don't forget to subscribe to the channel!
Be sure to check out my other videos in the links below!
⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️
How to remove orange peel from your paint
• How to remove orange p...
How to remove dirt from fresh paint
• How to remove dirt fro...
How to repair and paint your bumper
• How to save money pain...
How to remove fisheyes from your paint job!
• How to remove fisheyes...
How to save a bad paint job
• How to save a bad pain...
Disclaimer:
Due to factors beyond the control of Garage Noise, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. Garage Noise assumes no liability for any property or personal damage that may arise from doing a repair on your vehicle after watching any of my repair video's. Due to factors beyond the control of Garage Noise, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Again Any injury, damage or loss that may result from improper use of tools, equipment, or the information contained in this video is the sole responsibility of the user and not Garage Noise.

[@HotRodModz]

Thanks!

[@mikesrandomvideos]

I was unable to get mine to stick well enough to even use the slide hammer. I used my regular welder to weld on washers and use the hook on the slide hammer to pull out a dent. So far a dud. IMO

[@GarageNoise]

Was it on high setting?

[@GarageNoise]

And make sure your grounded well

[@obediencedenied57]

Good detail on the adapters bro, I miss the Lenco I spent years with, looking at this. Thanks.

[@GarageNoise]

Thanks, I've used it alot simce this video and it works quite well .

[@Al-AzzawiMustafa2023]

Hallo
What you let in 06:39 blackspray ??

[@GarageNoise]

Guide coat or flat black paint.

[@terryhall5811]

I like mine and just like you said about the ground yeah it sucks

[@GarageNoise]

👍

[@austrebertoharomerida2975]

Que les costaba por el precio poner una tierra con imán

[@GarageNoise]

The ground is cheap on Amazon and easy to install.

[@FUNISI126]

Good

[@erica.900]

How did you mount the ground? Did you weld the tip?

[@xmydavx]

Its 380v or 220v?

[@GarageNoise]

It's 110v