Video není dostupné.
Omlouváme se.
2 wheels DIY Robot Smart Car Chassis installation process
Vložit
- čas přidán 8. 11. 2017
- Installation steps:
STEP 1: Insert the fastener into the chassis after tearing off the yellow protection wrap of the chassis,the fastener and the code wheel
STEP 2: Install the code wheel and fix the motor to the chassis .(Attention,the copper sheet of the leading wire of the motor should face outward,the same side of the wheel)
STEP 3: Fix the motor to the chassis ,then insert and tighten the screws.
STEP 4: Insert the screws and fix the battery container.
STEP 5: Insert the spacer and tighten the 8 screws to fix the hammer caster.Hold tight and insert the motor(protection fastener) to the wheel .
Buy the car:
Ebay.com: www.ebay.com/itm/222616630793
Follow us here:
Facebook: / myikeshu
Twitter: / yikeshuoffice
Instagram: / iyikeshu
Pinterest: / iyikeshu
Tumblr: www.tumblr.com/blog/iyikeshu
Very educative video! Can you please show how the wires are conntected to servos and the switch in more detail?
I really enjoyed this video because I was trying to wire up the switch and the motors, thank you
what is the size of the caster wheel?
THANK YOU SO MUCH ....
Bro can we also install additionally arduino uno in this
At what point do you attach wires to the motors?
Can u pls tell where to buy tje screws
How do I control direction of castor wheel
how much money for the kit set?
Where can i find this chesis. Please reply
what are the materials needed?
can you plus ultrasonic sensor☺🙏🙏
thank you
I want to wire up the esc that comes with this kit but don't know how, can you help?
No, fuc* off!
is there a code?
The wiring you can see at 4:34 is wrong. The car will run when off and it will cause a short circuit when ON.
Como lo puedo solucionar? Las baterías se calientan mucho 😭
Hello brother how to compile a program for this car, Please Rply me??
@NIRISH A/L ARULMURUGAN Moe brother if you don't mine ,send me a insta I'd or FB I'd bcoz it's easy to talk😀
its so dunb
i can t connect wires
tks
Lack information
4:27 you didnt really show what the plug is doing in the center.
and then he fastforwarded th video without showing us how to put the wires
why do my wheels fall apart?
Enserio todos saben inglés
Gracias
What is the front wheel name
Caster wheel
Assembly was helpful, but your wiring doesn't make sense: when you turn the switch on, the batteries are going to short!! And it also looks like the motors will run WITHOUT turning on the switch.
I was looking in the comments for someone that could explain that, because I was thinking the same.
That motors should rotate for both states of the switch but woll not be in short because the motors are in the middle.
I think in the same way
You are 100% correct i just assembled this and i followed the wiring from the film it looked weird but i thought that may be that's some special kind of switch .... but it its a standard breaker switch. the batteries started to heat up when the switch was in off position be cause the whole thing was short circuiting. Then again the motors run ok in the off position because there is a full circuit then .
@@m0riss Hello, how did you solve it? I have the same problem, the batteries start to heat up, please reply 🙏
طلع فيديوا للمقطع الأول كيفة تركيب لوحة الأوردينوا
How to set card board normal robot by own
SHE SCAMMED US
Bot is going back side nor front side
Se colocó un cable adicional no se de que manera pasaste el cable
Bruh wiring please
u do onething speeed till end who can understand tgat
Way you have nails like women?
الله ياخد فيك الحق استاذ التكنولوجيا
Ty ur ma man
he is running it backward. lol, what a noob.
Don't follow this vieo. I did so and my wires got burnt.