Impact Power Block / Plenum Upgrade Installation
Vložit
- čas přidán 27. 10. 2022
- A step by step tutorial on how to install the power block upgrade kit.
If you have any additional questions, drop it down below!
You can find the kit here:
utahairguns.com/fx-impact-x-m... - Jak na to + styl
Thanks immensely for the tutorial on installation of the power block. It's gratifying to get a tutorial video by someone who actually knows the names of the parts of the rifle.😉
We do what we can haha. Glad to see it was beneficial! Thanks for watching
Thanks for the encouraging and knowledgeable video on the installation of the power block and plenum, you really know what your doing and what each piece is called.
Great tutorial!
Thank you!
The only change appears to be in the stainless valve body itself (missing slots and bore change) . If im not mistaken you may be able to retain the serialized block. I didnt guage pin the transfer to check for more subtle changes. Not shooting 40 grain slugs, i wouldnt have bothered with the upgrade in hindsight.
I love video like this
Thanks for the vid, what is the use of the installing power block??
Clear and concise video. What is the make of the gun rest/work stand you are using ?
It is a Tipton Ultra Gun vise
I’m not sure I understand. I was going to buy FX Impact Mark 3 but it’s really expensive in Canada. I found a really good deal on a Mk2. I’m not clear on a few things. Does the Mk2 come with dual regulators from the factory like the MK3 or do you have to upgrade it? Does the addition of a power plenum 720 cc produce more consistent shots and more shots or does it have to be in conjunction with a dual regulator?
Hi good video body,but i did like you did but i dont know why now dont have power when i shoot....power block it have 150 y the 1 mitter have 180 but when i shoot it does not power....i dont know what it gronw....could you give any idea? Thank.
So essentially you can covert a mk2 to an m3 with the exception of the duel reg ?
I received 3 NBR 90 o-rings and 1 NBR-70 O-ring along with 3 little black balls is there some place I am missing the NBR-90 Oring during the install and what are the three small black Buckshot looking things?
I just received my kit and found the little black rubber balls. Did you get an answer on where these go?
How much do you guys charge for the upgrade?
How bad is it if I get minor tooling marks on the rod that the C1 attaches to? I have some minor tooling marks/scratching from where my pliers attached behind the C1. Do I need to replace this rod?
Yes, otherwtse you will be thinking about it during a crucial Match...
Can that Upgrade be used on the first Impact MK1?
Yep!
If I get a M3 these items are included? I am close to a purchase!
Yes, on the new M3s they do come standard
@@utahairgunsworkshop not the early M3s
Hello. My seller says that the FX M3 sold in 2022 are already equipped with the new power unit. How do you know if it's true?
Every new M3 would have one. This is for an upgrade from an Impact/Impact x/MKII etc..
To my knowledge, early 2022 M3s had the Power Plenum 720 cylinder, but do not have the Power Block. That's how mine is and I'm a bit disappointed. Take out your magazine and look at the back of the block. If it has 4 holes, it's the new power block. If it has 6, it's not the power block.
@@hurricaneaquatics A friend of mine bought the FX M3 with the new PowerBlock. We tested both but didn't notice a big difference. However, the two FX were at the same settings.
@@islacouledouce Thank you for letting me know!
No es obligatorio quitar el martillo 😊
Isn't that valve house the old type?, The new ones come with three large long cut outs..
The three large long cut outs are for pre-power block power plenums. Power Block valve houses do not have O-rings on the outside. They are inside the power block/power plenum
@@utahairgunsworkshop ah, thank you, that makes perfect sense..
Gotta say, the music is annoying and unnecessary