RZR XP 1000 Custom Magnaflow Dual Exhaust
Vložit
- čas přidán 22. 08. 2024
- Custom made muffler for 1K XP
Used an F-body Magnaflow muffler 2.5 in and out along with 4 inch tips.
Parts List
Muffler - www.summitraci...
90 SS Bend (3) - www.summitraci...
180 SS Bend (2) - www.summitraci...
Tip (2) - www.summitraci...
O2 Bung - www.summitraci...
Flange - ebay.to/2Bl1UHR
3/8 SS Support Rod - www.mcmaster.c...
Washer (2) - www.mcmaster.c...
3/16 SS Spring Clamp Rod - www.mcmaster.c...
Washer (1) - www.mcmaster.c...
This is one of the best vids I’ve seen. No music or rambling on about what you did and how you did it. Machine sounds great and definitely like the tips. Nice work on your XP AND the vid.
Best slip-on exhaust I have heard on a 1k RZR. Looks and sounds great!
Thanks!
i just ordered the muffler gonna try it out on my beater 570
That sounds and looks awesome great job
Damn! Sounds great!
How is the drone when cruising? Sounds awesome!
Man that sounds good! Would be willing to share some pictures and tips?
Thanks! Look through the other comments as I've answered a bunch of questions there, or shoot me an email if you'd like.
@@trandall I read through all the comments form the sounds of it you peiced pre vents together..
I couldn't find your email in your about section.
@@jasonjohnson2157 Yep just got some different 90 and 180 SS bends to piece it all together, the muffler, the flange from ebay I linked down below, then some SS rod to make up the mounts the mimic the factory muffler mounts exactly
@@trandall very nice! I will try and grab some screen shots from your video post, wish me luck!
Thanks again for the info!
@@jasonjohnson2157 No problem! Check the description as I finally put my part list in there. Also be on the lookout for another video I need to make of my newest muffler I made for it, along with a comparison of them all.
Can it be used for a Polaris turbo r 4?
Sure, you would just have to build it with the different flange for a turbo mid pipe
Do you think they would sound the same on a turbo r engine ?
Yes, should sound even better and a little quieter since the turbo helps to muffle it down more plus give it a different crisper sound@@eltrapper4732
@@trandallMy neighbor has a Gibson dual exhaust system on his turbo S it sounds a bit similar like the one in video but his sounds very loud and clean
How are the sound levels compared to stock? Does it still drone in the midrange like stock?
Much, much louder than stock, sounds great though, but louder, and it does tend to drone at certain rpms, but half of that is also my custom cage now and its different profile. I usually wore earmuffs when riding for any extended period of time due to that. I've since then made slightly different muffler and its quieter and much more tolerable.
Did you have to add a fuel programmer also
Nope, but I did anyways a little later
Would you build one for me? That sounds good
Did it make much of a difference after you put the programmer on?
Beats paying $900 for a prefabricated one and sounds the same if not even better
how bout the part number for the tips please
Just used some simple 4" tips from Summit, www.summitracing.com/parts/sum-690018
It doesn't matter which way to have muffler as long as it's a f body muffler ?
The muffler is a one inlet, to an internal T then dual outlet on each side, so as long as you have the inlet going to the right place, you can mount it however you want and use any F-body muffler really
U don't have part number or where u bought muffler
Magnaflow 12265
Does it have to be programmed after do this ?
Nope, but you gain a little more if you do
Sounds super throaty
Do you have any pics of your recent setup that you changed after this video, thanks
No, not really unfortunately, I need to make a new comparison video here soon! Right now I'm just running a single in, dual out same side muffler with the top tail pipe plugged off, which makes it much more mellow and just a little louder than stock.
I’m ordering stuff as we speak lol sounds killer, I’m gonna install it on my 21 xp41000, was looking towards the Gipson setup anyways and yours looks just as good but sounds better in my opinion, killer video buddy
@@brittanyrice9006 Thanks! Good deal, that's exactly why I went this route, liked the idea of the Gibson but didn't like the price, but in the end probably cost me just as much in supplies and time, but is a packed muffler versus chambered. My only caution is it is LOUD! So loud that's why I made the one I have now, but boy does it sound good and is one of a kind.
How’s it going man? Hay I looked up the muffler but it doesn’t look the same as yours. Can you help me out. The inlet is on top and the outlets are on the bottom....
Just flip it around however you need to, as you can see on mine the logo is upside down, inlet on the bottom right, outlets on the top
Thanks man for the help your side by side sounds nice.. have a nice day man.....
Can I just flip it around?
Quiet af.
Wow! That’s exactly what I am looking for! Can I get one from you?
Did you have any back pressure? Did you run a tune after?
Should be less due to a free flowing muffler. Yes, tune helps overall and seems to have a little more power.
Does the factory heatshield work with it?
Yes, but I had to make new upper heat shield support brackets to clear the tubing on both sides
Any chance I could get some pics of how its mounted like the lower part where the factory has that square resting tab what did u do there? Also is it all stainless?
Sure send me an email and I can send you some pictures. I just used the same SS rod I used for the upper mounts along with a washer to fit over the factory tab. It is all stainless, muffler, tubing, and bracket rods, only thing not is the tips and flange to mount up to the factory two bolt connector. I even added two factory 2.5" spark arrestors on each side since making this.
How do I send u my email without posting it publicly
You can see me email in my channel about page
What was the final cost? And did u get hp numbers?
Cost around $500 in parts by the time it was all said in the done, but then took some time to get it all designed and built. No idea on HP numbers, I'd say it maybe gained 2-3 just guessing but it seems to have a little better low end along with noticeable better throttle response. I did get a tuner for it but have yet to put it on yet.
Bro don't lie to the people magnaflow costs $80 tops and you had the pipe already in the shop
Hey what kind of welder did you use for this? And what filler/stick did you use
I just used my MIG welder but all setup for SS, used stainless wire and straight argon since mine is a dual purpose MIG/TIG welder, even though I haven't got into TIG welding much yet
Troy Randall. Great. Last question is how loud is it? Is it obnoxious or is it a tolerable good sound
@@jesssantinio6935 That is one drawback/plus depending what you're after, it is loud, and I mean LOUD. So loud that I usually wear my bluetooth earmuffs when out riding it on the trails. It sounds really good but it does tend to drone which can get to you. That is actually why I made a second version here just a few weeks ago, just a single in on one side and dual out the other facing downward much like the factor muffler look, and it is quieter but still sounds almost as good as this one. Then with it I can actually use a 2.5" quiet cap on one tip and that quiets it down even more, almost just a little above stock then. I'm going to try to get a video made up and posted of it here soon.
Troy Randall yeah that would be awesome I think I would rather do that. If you could post a video and give me the part number of the muffler you used that would be great man. Trying to save a few bucks but I don’t want something too crazy loud like the first one you had. Did sound amazing though
Bad fuckin ass
You have a part number on that exhaust
Yep, Magnaflow 12265
Did you use the pipe off the factory muffler for the Flange
Nope, found a 2.5" flange kit off amazon so used just the one side from that and worked great
flange kit part number or link?
Here is the flange I used, worked great. amzn.to/2y7pRx4
Did you cut and bend the exhaust tubing or buy it?
I just bought some pre-bent 2.5" SS tubing and then cut and welded it back where I needed to
Probably spent no more than 80
Ha I wish, I did it the right way and stainless tubing ain't cheap, so worth it though! Still looks like it does in the video even two years later.
The maganaflow is probably $120-130
The 90° stainless bends are a good $40x5
Decent stainless tips $50-60.
I i was to fab someone this set up id charge close to $800.
Stainless isn't cheep and custom isnt cheep.
Yall funny 🤣 $80 hahaha
@@scoomagee Exactly!
I can either send you my email or phone number for us to communicate and hopefully get one of these! Let me know thanks
Hey, my email is in my about under my channel info if you wanted to reach out that way. I'm not making or selling these really, just put up what I came up with, but I could give you some pointers and/or tips if you wanted to reach me, thanks!