Fantastic. I only do the belt every 4 or 5 years and it's a great refresher and reference. One thing I noticed was that after putting everything back, the mark on the crank pulley was slightly past (clockwise) the mark on the cover. Referencing your video I can see that it's exactly the same as mine once you've rotated two turns, so this is just a normal case (stopped me worrying).
excellent job , you make it look effortless , i did mine blind ( without seeing your video i mean ) and it was a nightmare , mind you my engine was still in the car , did the water pump and tensioner and uprated gasket set including inlet manifold green jobby , shes purring like a kitten since , just have to put a clutch in her now !!
the best way I found to lock the engine on a very very tight honda engine crankshaft pulley bolt, was to take an old starter motor, just the gear/dog end.. weld it solid, then install it.. 100% locked...
you all prolly dont care at all but does someone know of a trick to log back into an instagram account?? I was stupid forgot my password. I would appreciate any help you can offer me
@Grady Gavin i really appreciate your reply. I found the site through google and Im waiting for the hacking stuff now. Takes quite some time so I will reply here later with my results.
thanks for posting, im fitting a new mls gaskit kit with new cam kit to a 2000 rover 25 1.4 i needed to check over the timeing marks on bottom crank thanks vry much :)
thanks alot. At the moment i was trying to remove pully of the crank to change water pump and at the same time i change the timing belt. but i can't. this clip very usefull, thanks for your help and genuin info
The springs on the valves tend to push against and partially rotate one or the other cam...so you would not be able to line it up to put the belt on....unless you had another pair of hands to hold them in the right position whilst you slipped the belt on...which would be a bit hard without him getting in the way. Tools can be had NEW for £6 with free postage on ebay
You can add sealant such as hylomar together with the oil seal o-rings ..it will help to keep corrosion off the faces...and help protect from road salt attack from the outside ...that's a tip for long term ownership ..if you only plan to keep the car for less than two years ...don't bother .
Great and helpful video. What is the difference between the manual and auto tensioner? do they come off in the same way? Also why does the engine need to be timed first with the crank pulley marks? Thanks
The line on the crankshaft pulley he has it lined up in the video is the "safe" position for changing the belt..In the safe position all pistons are half way up the bore..means you cant accidentally hit the valves against the pistons in this position whilst changing the belt.....The other mark has nothing to do with this job...it is is used a for checking the "ignition" timing, with a strobe light, with the engine running.
The top timing markers on camshafts with white spots. On those camshafts arms it's written "exhaust" and in riverside is "In". So witch sides of camshafts arms should be close to each over? "exhaust" and "In" or "exhaust" and "exhaust" Thanks in advance.
@@metalworker007 it doesn't, I just undid it with old trick. Rest a socket wrench on something solid, chassis leg in this case, and flick the starter, several times in this case. Thanks anyway.
Is it completely necessary for a cam locking tool? as long as I'm careful and don't rotate them to an extreme? could I mark the cams to the cover using a different colour to ensure they aren't 1 degree out? ect. Also the crank pulley how would I go about locking this if the engines still in the car? Sorry I haven't done a terrible amount of research.
Does anybody have some advice on what to do if the top two bolts of the plastic cover are spinning in place? My guess is the mechanic shop that did the belt the last time over tightened the bolts which caused the captive nuts to break free inside the plastic... Any suggestions would be much appreciated!
Hello again, finally i took the engine a part, i have the parts but now i need to download a rebuilding manual with the torques and also how to assamble the valve head and the timing, any sugestions where to find video or digital manual??? thanks a lot.
The official rover manual is called "RAVE", its still copyrighted ...and me pointing it out on a public forum would put me in the wrong but you now have the main search term, you just add the model :)
just done my grandsons rover 25 new cam water pump@ belt now it won t start some help would be nice any my grand son is stundt thanks any help i would be very gratful sorry about spelling
Does this answer your question .. Sorry cant put links in the answer..but go to Google images ..use search words "rover k-series timing marks" the first picture to come up ..is the one you want . YOU CAN ALSO PUT YOUR OWN MARKS ON IT BEFORE YOU TAKE IT APART ..IF IT HELPS YOU PUT IT BACK TOGETHER IN THE RIGHT ORDER .
Can all timing belts, water pump etc be changed on a KV6 engine in a Rover 75 while engine is still in the vehicle. Only videos i can find are engine out of vehicle which is obviously much easier.
hello, last person how change all gaskets on my lotus s2 with rover engine do some wrong because now i have noice on the cam followers, what i should do? thanks for your help
The gasket is called an MLS gasket..multi-layered-steel..for advice on what to buy and where to buy .stating your location ..post on "rover.org" in any forum there, that deals with the k-series engine rover 200 or 400 or join one of the lotus forums. I cant possibly give you all the advice you need here..as it comes out upside down and the wrong way around in these threads .,.I cant post detailed info here, it will be too hard to follow. You need good step by step guides .they are on the forums
I honestly cant say what could be wrong ..other than they been very careless doing the rebuild... dirty conditions.... blocking the oil ways ..heads should have the sub-assemblies put together with anaerobic sealant only .also they could have.got the followers mixed up ..maybe they put them back in the wrong places ..as they should go back into the exact positions they came out of...These engines need new improved upgraded gaskets when put back together or they will fail again .
Fantastic. I only do the belt every 4 or 5 years and it's a great refresher and reference. One thing I noticed was that after putting everything back, the mark on the crank pulley was slightly past (clockwise) the mark on the cover. Referencing your video I can see that it's exactly the same as mine once you've rotated two turns, so this is just a normal case (stopped me worrying).
excellent job , you make it look effortless , i did mine blind ( without seeing your video i mean ) and it was a nightmare , mind you my engine was still in the car , did the water pump and tensioner and uprated gasket set including inlet manifold green jobby , shes purring like a kitten since , just have to put a clutch in her now !!
Thanks a lot, very useful video. Tomorrow I going to try changing the cam belt, for a new one.
the best way I found to lock the engine on a very very tight honda engine crankshaft pulley bolt, was to take an old starter motor, just the gear/dog end.. weld it solid, then install it.. 100% locked...
Great video, think my tensioner has started to rattle so I'm going to have a check after watching this
thanks for uploading this video, I've learnt lot. Just replaced head gasket for my cousin's car.
you all prolly dont care at all but does someone know of a trick to log back into an instagram account??
I was stupid forgot my password. I would appreciate any help you can offer me
@Brecken Briggs instablaster =)
@Grady Gavin i really appreciate your reply. I found the site through google and Im waiting for the hacking stuff now.
Takes quite some time so I will reply here later with my results.
@Grady Gavin it worked and I actually got access to my account again. I am so happy:D
Thank you so much you saved my ass!
@Brecken Briggs no problem :D
Great video, very well explained thanks for sharing!
thanks for posting, im fitting a new mls gaskit kit with new cam kit to a 2000 rover 25 1.4 i needed to check over the timeing marks on bottom crank thanks vry much :)
You said rotate the tensioner clockwise but rotated it anti clockwise, which direction is it?
The Rover workshop manual says anti-clockwise 👍
thanks alot. At the moment i was trying to remove pully of the crank to change water pump and at the same time i change the timing belt. but i can't. this clip very usefull, thanks for your help and genuin info
The springs on the valves tend to push against and partially rotate one or the other cam...so you would not be able to line it up to put the belt on....unless you had another pair of hands to hold them in the right position whilst you slipped the belt on...which would be a bit hard without him getting in the way.
Tools can be had NEW for £6 with free postage on ebay
Just did this job, engine running perfectly but whiring / whining noise coming from new belt 😢😢
You can add sealant such as hylomar together with the oil seal o-rings ..it will help to keep corrosion off the faces...and help protect from road salt attack from the outside ...that's a tip for long term ownership ..if you only plan to keep the car for less than two years ...don't bother .
Very clear. thank you
great video really helped me out , thanks mate,
Great and helpful video. What is the difference between the manual and auto tensioner? do they come off in the same way? Also why does the engine need to be timed first with the crank pulley marks? Thanks
Great video. A shame we can't do the work with the engine out
The line on the crankshaft pulley he has it lined up in the video is the "safe" position for changing the belt..In the safe position all pistons are half way up the bore..means you cant accidentally hit the valves against the pistons in this position whilst changing the belt.....The other mark has nothing to do with this job...it is is used a for checking the "ignition" timing, with a strobe light, with the engine running.
The top timing markers on camshafts with white spots. On those camshafts arms it's written "exhaust" and in riverside is "In".
So witch sides of camshafts arms should be close to each over? "exhaust" and "In" or "exhaust" and "exhaust" Thanks in advance.
Great video. Excellent !
Hello
What should be the protrusion of the cylinders from the plane of the block?
Rover 214 si, k-series, 16 v, 1400 motor, gasoline
mm good stuff. Shall we do the water pump at same time.
Excelente video
if I take out 1,8T Rover 75 and replace with 1,8 non turbo engine from Free Lander do I have to reprogram the computer to match the other engine
Excellent video, thanks for your effort to make it.
Does crankshaft bolt have any threadlock on it by any chance?
Ask Technozen of mg-rover.org
@@metalworker007 it doesn't, I just undid it with old trick. Rest a socket wrench on something solid, chassis leg in this case, and flick the starter, several times in this case.
Thanks anyway.
great video..please can you tell me ,is this procedure for a landrover freelander 1 1.8 petrol model
Is it completely necessary for a cam locking tool? as long as I'm careful and don't rotate them to an extreme? could I mark the cams to the cover using a different colour to ensure they aren't 1 degree out? ect.
Also the crank pulley how would I go about locking this if the engines still in the car? Sorry I haven't done a terrible amount of research.
When is comes to cambelt failure, Is the 1.4 a "safe" engine? Or would valve/piston contact occur?
Did you get the answer? I’m in need of it?
@@l33lvr it an interference engine, the valves will hit the pistons.
Does anybody have some advice on what to do if the top two bolts of the plastic cover are spinning in place? My guess is the mechanic shop that did the belt the last time over tightened the bolts which caused the captive nuts to break free inside the plastic... Any suggestions would be much appreciated!
Try a plastic tool between the inner cover and head to keep the tension on the bolt whilst trying to undo it.
timing markers on camshafts pulley should both angles write down "exhaust" those with whites spots? Thanks.
Mate did exactly what he said and started it up blew a piston and rods
Hello again, finally i took the engine a part, i have the parts but now i need to download a rebuilding manual with the torques and also how to assamble the valve head and the timing, any sugestions where to find video or digital manual???
thanks a lot.
The official rover manual is called "RAVE", its still copyrighted ...and me pointing it out on a public forum would put me in the wrong
but you now have the main search term, you just add the model :)
if you have the money ..you may as well ..under £30
cam belt tensioner pulley ..change that if engine has done over 60,000 miles
any recomendation, what to buy and where to.
thanks a lot.
Is it possible to be 180 out?
just done my grandsons rover 25 new cam water pump@ belt now it won t start some help would be nice any my grand son is stundt thanks any help i would be very gratful sorry about spelling
morgan gale I'm in the same boat any help would be appreciated
morgan gale Hi timing out. Happens every time
Cheers
Nick
UK
Ask the man who owns one
Please tell me which type of sealant was used?
and one more thing, do you need any sealant when changing water pump or is it enough O ring rubber?
would it be OK to go start the car after iv got all cams lined up and the pulley lined to safe. would the car start and to safe to drive ?
Merci pour le partage .
Does this answer your question ..
Sorry cant put links in the answer..but go to Google images ..use search words "rover k-series timing marks"
the first picture to come up ..is the one you want .
YOU CAN ALSO PUT YOUR OWN MARKS ON IT BEFORE YOU TAKE IT APART ..IF IT HELPS YOU PUT IT BACK TOGETHER IN THE RIGHT ORDER .
Thank you very much!!!
Can all timing belts, water pump etc be changed on a KV6 engine in a Rover 75 while engine is still in the vehicle. Only videos i can find are engine out of vehicle which is obviously much easier.
iiTechnology t/a Scott Inwood Computer Services d'iris d air
iiTechnology t/a Scott Inwood Computer Services dirigé d'air
i would have released the cam sprockets before setting the tensioner! anyone knows why?
As far as in aware ..the auto box version has a Honda engine not a k-series as above.
The white spots are not on an original untouched engine ..these are added by the person who takes it apart.
hello, last person how change all gaskets on my lotus s2 with rover engine do some wrong because now i have noice on the cam followers, what i should do? thanks for your help
What are the two marks on the Crankshaft pulley for?
Was the 96 820 si fitted with a k series?
Clockwise ?
You tired it anti clockwise
The gasket is called an MLS gasket..multi-layered-steel..for advice on what to buy and where to buy .stating your location ..post on "rover.org" in any forum there, that deals with the k-series engine rover 200 or 400 or join one of the lotus forums. I cant possibly give you all the advice you need here..as it comes out upside down and the wrong way around in these threads .,.I cant post detailed info here, it will be too hard to follow. You need good step by step guides .they are on the forums
А с коробкой на автомобиле как закрепить коленвал от проварота ?
well done
thankyou
I honestly cant say what could be wrong ..other than they been very careless doing the rebuild... dirty conditions.... blocking the oil ways ..heads should have the sub-assemblies put together with anaerobic sealant only .also they could have.got the followers mixed up ..maybe they put them back in the wrong places ..as they should go back into the exact positions they came out of...These engines need new improved upgraded gaskets when put back together or they will fail again .
sorry ..don't know ..rephrase your question ..
I very please remake this video with HD quality
Envious of your knowledge mate, are you working in Ireland??
Kev.
Привет друг, можете мне написать вин номер Ровер 75 для поиска запчастей а то мой вин не пробивается
perfection thankyou
Клапана гнутся при обрыве ремня при заводе двигателя. За ранее спасибо
Гнутся еще как
Is this a non interference engine?
it will destroy itself if the belt snaps
En castellano hay video
То что надо
soy español porfavor quiero saber timing marks de MG ROVER 25 petrol 1795cc engen
stupid me :) thanks
me lo podes tradicir en español
Rover 200 1999 1.4 16v ok
dont understand rubber belts why not use chains ...garbage!
Thanks