Flight Modes | INAV 5 on a flying wing | 8/11
Vložit
- čas přidán 21. 08. 2024
- Support my work / pawelspychalski
Today, let's cover the INAV flight modes that you might want to use on your flying wing. Or any RC airplane in general: Position Hold, Angle, Return To Home, and others.
OSD - Analog, DJI FPV, and HDzero | INAV 5 on a flying wing | 9/11 • OSD - Analog, DJI FPV ...
OSD - Analog, DJI FPV and HDzero | INAV 5 on a flying wing | 9/11 czcams.com/video/rWqMohsu9co/video.html
so much pleasure to hear and see you; you are one the best inav teacher; thanks again
Thank you so much for these videos. The way you explain things just makes sense to me!
Glad you like them!
Hello Powel! What a great series about INAV 5.0 you have! I have a couple of questions from this episode:
1 Why are you coupling the Nav Althold mode to the Nav Cruise mode when the Nav Cruise mode itself handles the altitude?
2 Why don't you use the continuous Autotrim in the Configurator instead of allocating a switch for that mode?
(Following)
exactly what I was thinking, this is how I did it with inav 2.6. but the nav modes have changed in the new releases of inav
Pasha, day otvet
doesn't the cruise hold the altitude, and it's necessary to add altitude hold?
I think you are correct. It used to be called 3D Cruise prior to Inav 3.0 when you had to add Alt Hold to Cruise.
@@joemoffo9706 Yes, I fly a lot in NAV CRUISE without NAV ALTHOLD and my altitude is always very constant.
@@ApappieK same
Thanks Pawel, I would watch about the soaring mode. :)
Pavel you are amazing as usual. Thanks.
Is there a problem / forbidden that the Arm channel not be the last (12 in my case) and not immediately after the last Auxiliary channel?
There's nothing that prohibits it unless you are using ELRS, in this case, is a requirement (well, technically you can have arming in another channel but it's unsafe). It is more a matter of best practice.
Awesome, Pawel! Thanks a lot! 😃
Just one question... Are there any issues to have auto trim on all the time?
Anyway, stay safe there with your family! 🖖😊
There is continous auto trim feature. The flight make auto trim trims only for a few seconds and then goes off
Thanks for your tutorial! but I'm dying to see the next video covering the osd. I'm having problems with inav not showing the correct information. Such as enable (battery cell voltage) and something completely different shows up in the goggle osd. Even the satellite information is wrong. Not sure what's the issue but I hope I can figure it out.
Another awesome video, thank you so much for doing these series for us! I have question about not having NAV POS Hold in Inav 6 trying to set my Mini Drak up like you have here but this option is not available, let me know thanks!
I assumed Cruz Mode maintained altitude, I mean, why would it not?
I always select constant autotrim...Why would it be on a switch as well?....🤔🤔😳🇬🇧 Informative video, thanks..
thank you Pavel. About the Auto trim: instead to have it on the stick, I see that on INAV you can enable: Continuously trim servos on Fixed Wing. What is the best please?
It must be tiring explaining the basics like how to set acro over and again, then again as engineers one has to wonder why this is needed.
So with ‘Auto’ trim and tune on the same switch but with ‘trim’ first from the off position, suggests you should initiate auto trim first before auto tune, right?
Hello Pawel. Inav recognised the channels until the ch8. Not recognising ch9. Any tips? Thank you. Great explanation so far on setting up inav on a flying wing
It could be that your remote or reciever doesn't support past 8 channels
iNav 5.0 or RPM filtering configurator say must hast ESC telemetry, is it still need to be wired telemetry or can it get fro belheli32? FYI, motor remapping does not work, change it and apply and save reboot and it's back to 1234 original order and not change which motor spins.
Is there no collision of mods when two radio channels control the choice of flight mode?
Modes follow a preset order of priority. MANUAL>RTH>WP>NAV MODES>ANGLE>ACRO
@@theHDRflightdeck
so if one channel sets MANUAL and another channel sets RTH... MANUAL wins? Wing will not come back?
@@Tonynux correct
what is the reason on Windows and linux, drog is flashed but does not connect. flight simulator tmotor f7.
Advice for setting up moder nav rth is not available on moder page. I would like to ask why, why is it wrong?
With the Inav 7.0 is the magnetometer for a Delta wing still not required? Trying to set up a new AtomRc Dolphin. thank you.
magnetometer on airplanes was never required
so people say i cant auto tune in angle mode but i do and it flys perfect. I just flew in acro yesterday for the first time and it flys great . people say that auto tune is meant for acro only. Is that true? because auto tune works great in angle mode for me every time to tune a new plane
I am using INAV 7.0 and setup modes/switches just as you have here ,but when i add manual mode to lower range, and leave the top range open, ACRO mode never come in. The only way i am able to get the results you have is to use ANGLE mode instead. What have i done incorrectly?
No idea what might be but I expect one of the ranges is incorrect. Manual is independent from acro
No autolevel ( must use it in angle mode).
Thank you so much for this playlist, almost finish to build my first fpv wing following your tutorial
In my case I have set just angle, manual and acro in a switch in that same sequence
I'm curious about if I can set the cruise and althold in another switch for use it even when i'm flying in others flying mode or is required to disable one of the other for use it, by the way I don't have poshold on my inav modes tab, why could be?