2019/2020 Toyota RAV4 rear reflector LED install
Vložit
- čas přidán 23. 06. 2020
- Wanna add a nice simple mod to your Ravy this is the best way to do it.
Here’s the light sequence setup:
WHITE to brake light green
Black to brake light black
Red to bottom bulb green and white
Signal yellow to green
Here’s where I purchased: wookiesshop.myshopify.com/pro...
thank you for sharing this video. I did it your way and love the way the car looks :)
Thanks man! Really helped with my install!
Thx for wiring notes! PS, I was able to get a small ratchet with a Phillips bit in behind the bumper easier than the stub screwdriver. A person with small arms can get to it from underneath the SUV. 😊
Thank you for your help l just received the lights thank you
No problem ENJOY!
That's awesome!
Thank you for this!!!! MY RAV LOOKS SO MUCH BETTER!!
Everything is good but I'm make a new hole in the center to pass the cable back is better for cables 👍👏
Joaquin Padilla I love that idea wanted to keep it simple for folks though you know.
Hi bro, thank you for your video, please can you send me a link for this led please,? Thank you 👍
What is the gauge number of the T-taps that you used?
22-18
You guys really installed these lights without removing the bumper?
I tried but I couldn’t pull the bumper away far enough to get my hand back there and I felt if I pulled anymore something was going to happen! How did you do it????
Hand size honestly plays a part in this
You may need someone with smaller hands
@@bigbanka5572 it was easy to go underneath. take off 2 trim button clips and you can reach up and in.
@@curt6531 you know thanks for that
Idk why I didn’t think to just go under
Under Here's the light sequence setup: I think this is what you meant to say
WHITE TO TAIL LIGHT POSITIVE BOTTOM BULB GREEN & WHITE
BLACK TO BRAKE LIGHT BLACK
RED TO GREEN BRAKE LIGHT POSITIVE
YELLOW TO TOP SIGNAL GREEN AND BLACK
Could you help me by giving me the address of the website you have because I bought the lights and no response from then thank you
Sure thing the link I have should work still
Let me message the owner
@@bigbanka5572 thank you for your help
I do not get emails from them where is my order
@@edwingonzalez4645 I sent out an email to him
Just got a email from them thanks for your help
Question?? How do I know what color of wire goes connected to which wire in the stop lights, you just show the green connectors on the stop lights but didn’t show what color wire is connected at the end??? Please advise thank you good video though
What car?
@@bigbanka5572 a Toyota Sienna
@@bigbanka5572 2017 Toyota Sienna thank you love your video sir
@@oscarsanchez8019 did you figure it out?
@@bigbanka5572 yes I did 👍🏽 it was easy thank you
Water gets in and that is it.
You mean Signal Yellow to Green and Black -and RED wire to Solid green; abd White to bottom bulb green and white~ at least that is what you stated and showed in your video.
so... per factory installation says: - "Connect the black wire to negative, red wire to brake light positive , and white wire to tail light positive, yellow wire to the signal light" So you have the RED going to the bottom bulb green and white tail light positive ~instead of to the GREEN brake light positive and you have the White going to the light green instead of the tail light positive which is solid green. It was a well made video and I appreciate and understand it because you explained so well and did a great job. But, some folks may get confused at your light sequence setup writing. Now I am really confused, Sorry If you're right, then I apologize.
Correction: Tail light positive is bottom bulb green and white.
Can someone please tell me what the exact hookup is.Thanks
Did you have luck with wookiesshop I think I lost my money
Yes there site is on going some changes they see your order you should get an email this week. I’ll write them again sorry about that
It's not your fault thank you for your help God bless you
2 weeks and know email I very disappointed with the company 😞
Does it void car warranty?
No that’s why we use wire taps instead of splicing
Men this video giving me a headache get a camera stand man 😖
Here is my latest update: These lights disabled my car's collision detection and cruise control system w/errors on the dashboard. Those systems are linked directly and indirectly to the brake lights. These lights interfere with the brake system when they malfunction such as water penetration into the light's housing. Toyota won't touch my car until those lights are removed.
Yeah you definitely did something wrong
I still service my Rav4 till this day
@@bigbanka5572 Actually the water condensation in the light is causing a short in the electrical system; which in turn causes the collision detection system to shut down. The collision detection system will apply the brakes if a collision is imminent. And if it thinks the brake light is not functioning properly, it won't automatically apply the brakes. Besides the shut down of the collision detection system, the LED lights were functioning as advertised despite the water condensation. The dashboard errors went away after those LED lights are disconnected.
@@Chitown388 ah I see what you’re saying
So your product was faulty that you purchased
And water got inside
@@bigbanka5572 If I do this again I would
1) look for a product that specifically says it's waterproof. The manufacturer of my lights, AMOPA, actually says their lights need heat ventilation so their lights are not waterproof
2) dunk the light in water for a couple of hours to make sure it's waterproof before installing it; it's a big hassle to uninstall.
@@Chitown388 yeah always check it out first before installing
My lights have been through numerous power washes holding the water blast right on them and tons of snow and rain storms.
Shoot me a subscribe by the way!
Don't buy these LED lights with the AMOPA brand name. Those LEDs have water condensation inside the light. AMOPA told me that their LEDs need heat ventilation. This implies that these AMOPA lights are NOT waterproof. Their recommendation is to remove the light to "air it out" ... as if removing the rear bumper to do this is a 2-minute ordeal.
Horrible video production quality.
Seems like you didn’t get it done right
@@bigbanka5572 your camera is all over the place.
@@bigbanka5572 you need cut out unnecessary parts out of your video. Way too much movement with camera,very hard to watch the whole video. I appreciate your video but you need to edit it better.
@@nazarettos6987 no problem thanks for the tips