How to change a sharp v5 tube into a benjamin canon || C~1
Vložit
- čas přidán 12. 09. 2024
- 2 in this video only theory,
"For those of you who want to change the function of the gun tube"
how do i change the uklik sharp tube into a uklik benjamin canon tube...
I have a uklik sharp v5 brass tube 7cm long for a 22mm OD pump pipe, :
(why do I have to bother with this, bro... at first I wanted to make a sharp knife because what I have is a sharp od 22 gun tube, that's why I bought a stainless pipe,
it continued to be made but after rethinking the cost was too much, finally I changed my mind and switched to the trigger that was already there, that's why I did this experiment with sharp tubes so that they can be used and I don't need to buy tubes anymore...
good results...!!! )
1 ~ the first step is to drill the inner surface of the tube for the valve place, adjust the diameter to what you want, don't drill it too deep, leave a few millimetres for the cone leg holder / rear valve valve seat funnel
2~make a conical funnel with an iron or brass axis continuously drilled or with a small pipe or a piece of the barrel to taste, shape it using a file with the front end like a cone but not too sharp, just enough.
as in the hole with a drill, adjust it to the valve as you want to use 3,4,5 mm,
3~Install the finished funnel/cone in the tube with neat iron glue or power glue.
4~ Cut the plastic pipe used for sewing thread, paralon or enough water hose and put it into the tube to make a ring holder
height adjust to the neck of the cockpit or higher,
and later the nipples must be higher so that they can suppress the nipples/gotrit
5~ The front valve can use a used gas lighter, gotrit, or you can make your own from a bolt, take the head and shape it and leave it behind the bolt head a little to hold the spring so that the spring doesn't wobble later,
continue to drill the center of the bolt head, plug in enough nails, it looks like a gas lighter, so give the nose enough,
when it's done, just put a rubber pad and then glue it using power glue so that it sticks firmly..
6~ the front and rear valves must have the right pressure so that the air that has been stored in the pump does not vomit again,
7~ Try not to make the rear valve too thick so it doesn't bubble when pumped a lot, and even then, if you make your own nipple,
8~ the valve holder for the front valve, you can use an inlet or seal but it must be loose a little about the size of the inlet, so that the seal or rubber holder can live / move when we pump,
9~ the rear valve depends on what you want, the original canon, you can make it yourself, the important thing is to adjust it,
10~ the neck where the burr is used is ok, if you want to take it off it's good to make the tube space wider, the most important thing is to adjust the valve and spring.
if you if yes..
I want to change the Sharp V5 tube into a Canon Uklik tube, this method I have tested and tested, it's great...
this assembled power tube is quite ok like the original canon uklik tube,
"(provided you assemble it correctly)"
I put it on my mini trigger button, it's actually less than optimal, the trigger isn't strong enough,
a maximum of 7_8 x pumps for my trigger, if the pump above it can shoot 2 x,
for those who use a hammer per straight, it is definitely more stable, because the thrust of a straight hammer is more maximal,
how to change the uklik sharp v5 brass air gun tube into a benjamin canon uklik gun tube
this my style...
🙏🙏🙏
description
description
Keren pisan ni lur..apalagi kalo dikombinasikan dg video berburunya yakin bagus banget..sukses slalu
Siap
Ok
Maaf bang mau tanya, pelatuk saya, rencana mau di tanam pake tabung canon, boros ganti sil kalau original, kira2 itu as pentil panjangnya berapa centi? Soalnya mencocokan lubang transfer angin sama pelatuk kan lumayan lebar jaraknya,
Klu minta buatkan untuk benjmin berapa bang upgret kyk gitu..?
Boleh ni idenya bro....
Siap...
Full upgret y lae...
Ya mas lae....
Bro bisa bntu rubah pnya sys seperti itu gk
Bang Chamber tgr od 25 elepant cocok gak klo di pasang di jawara Ace deluxe
Jawara tiger, Cocok bang,
Lubang tranfer anggin qu ko ketinggian ea bang...jdi Chambernya naik turun gt..mohon penjelasannya bang..
@@asbr4347 .. Mentok di tranfernya ya sama punya saya juga,
caranya sebelum laras di pasang lubang transfer di chamber bor lagi sesuaikan dgn sil oring, bor ampe tembus scara per lahan, jd si penyambung transfer langsung mentok k laras,
@@asbr4347 si transfernya nnti kikir perlahan klo masih ketinggian, ,
Si laras juga nnti kikir scukupnya permukaan bawahnya untuk transfer biar agar rata,
Maaf bang coba kirimin Vidio detail nya dari ngerakit tabung sampe pemasangan tabung di senapanya....soalnya senapanya sama bang🙏
Y inshaAllah nanti bang kalo ada waktu sy bongkar bikin vd nya...