I’ve been going through these Prince valves for over 40 years, the only thing I do different, other than I have a parts washer, is the final assembly of the spool. The edge of the spool land is really sharp, if you leave the seal clear back against the support plate/spring assembly and put a little grease on it, you have less chance of cutting it. This I speak from experience. Otherwise, this man did a nice job. If he paid attention, which I gamble he did, he can reset the relief within a smidge if where it was, probably close enough for what this goes on. He’s obviously done enough if these to know how/where to set it at. He honed the body with a lather and by hand, this was pretty ingenious. Consider where he’s at and what supplies he has, he’s talented. Nice job sir!
Ok. I gotta give this guy some props for a few things. 1. He has a work bench. 2. His shop is well organized. 3. He's wearing boots. 4. He used an actual micrometer. All he needs now, are a few more tools and a parts washer. Good job.
Well this is one well done job. His workshop is quite tidy and organized, seal rings are nicely packed in clean plastic containers by sizes. His tools are very basic but they get the job done. He works very carefully and collects all the parts washes them and inspect them using real, proper micrometer. While doing the assembly, he carefully oils everything and never uses excessive force and all parts remain very clean all the time. I have seen this particular mechanic in few more videos, he is specialized in hydraulics and he is doing the same quality work every time. There is place for improvement but only in better tools, workbench, some more headspace (he seems quite tall) and parts washer. So, this mechanic deserves full respect for his job. I must say that he is one of the rare examples of how job should be done even if you have not so ideal workshop and tools. You simply must invest lot of skill, attention and care in what you are doing. Great job mate!
This is the miracle of the Indian economy (doesn't matter if it's not india). Lack of production capacity, only the industriousness of the people, hopelessness and golden hands
этот пилять 40 годы наверно, чугунный притир🤦🏻♂️ давно алмазные регулируемы развертки есть.... да ещё и на такой скорости в горизонтальной плоскости 🤦🏻♂️🤦🏻♂️🤦🏻♂️, и чем он там микроны ловить будет?
Миксер мне в глаза но я смотрю его только из-за его спокойствия а не из-за навыков ,несмотря на критику со стороны аудитории в их сторону они делают свою работу пусть даже и не качественную но работу по улице не шлангуются дурь не шмаляют фанфурики не пьют,обычный человек который любит занятие и получает удовольствие от проделанной хоть ненастолько качественной но работы.
С таким талантом и я могу поменять колечко резиновое на каком-то клапане из-за которого скорее всего и уходила жидкость. А вот притереть посадку поз золотник это конечно нужен "опыт". Золотые руки чё сказать 🤣
This guy is excellent, I’m very impressed simply because I never thought these valves could be repaired, obviously I was proven wrong. Excellent work and I really enjoy watching your channel!!!!!!
Grande,lavori che da noi nemmeno si sognano di fare e poi impressiona la tranquillità e la manualità di questo ragazzo,bravo!! Saluti dall'Italia!👍👍👍👋👋👋
это регулируемый предохранительный клапан, а не гидрорегулятор. и он зажал его НЕ рабочей стороной. "рабочая грань" у него снизу на торце. так что он все норм сделал.
Hi from Australia, I really enjoyed the content of your video and the skill you demonstrated, I like hydraulics and found your channel very interesting. Thankyou for posting
lapping the bore would increase the spool clearance and cause more leakage ! Only if you fitted and lapped a over size spool would this method improve things. The only reason it held fluid after was the assembly oil viscosity stopped the flow. The clearance of the spool to the bore is worse than before. If I am overlooking something here I would love to hear it !
Ахуеть. Просто пассатижи и шестигранник. Ни воротков, ни трещеток, не говоря уже о динамометрическом ключе. И на вид делает работу аккуратно. Respect! P.S. интересно, что там в бутылке: растворитель или бензин?
Тут хотя бы похоже на нормальный ремонт. Я думал будет по классике - пошоркать прецизионные поверхности наждачкой, и покрасить снаружи - вот и весь ремонт...
На камазе есть ремонтный участок занимаются ремонтом и обслуживанием распределителей ,точат если нужно новые залотники и хромируют при установке ремонтных размеров.
Agame un favor comoago para quitar una fuga en racor qestan en un banco de balbula en una máquina qe ya no consigo las arandelas orijinales qeson encauchetadas
I’ve been going through these Prince valves for over 40 years, the only thing I do different, other than I have a parts washer, is the final assembly of the spool. The edge of the spool land is really sharp, if you leave the seal clear back against the support plate/spring assembly and put a little grease on it, you have less chance of cutting it. This I speak from experience.
Otherwise, this man did a nice job. If he paid attention, which I gamble he did, he can reset the relief within a smidge if where it was, probably close enough for what this goes on. He’s obviously done enough if these to know how/where to set it at. He honed the body with a lather and by hand, this was pretty ingenious. Consider where he’s at and what supplies he has, he’s talented. Nice job sir!
Ok. I gotta give this guy some props for a few things.
1. He has a work bench.
2. His shop is well organized.
3. He's wearing boots.
4. He used an actual micrometer.
All he needs now, are a few more tools and a parts washer.
Good job.
And he is not working on the floor...
You forgot to mention he was pouring water from a silver chalice, that was the icing on the cake 🤣🤣
Gift him a Dewalt battery drill and he would increase production by at least 50%.
@@tima.478 Подари. А то у нас дорогие стали🤣
@@user-ol8vq1qo6n For FREE....naaaaahhhhhh... 😅
Well this is one well done job. His workshop is quite tidy and organized, seal rings are nicely packed in clean plastic containers by sizes. His tools are very basic but they get the job done. He works very carefully and collects all the parts washes them and inspect them using real, proper micrometer. While doing the assembly, he carefully oils everything and never uses excessive force and all parts remain very clean all the time. I have seen this particular mechanic in few more videos, he is specialized in hydraulics and he is doing the same quality work every time. There is place for improvement but only in better tools, workbench, some more headspace (he seems quite tall) and parts washer.
So, this mechanic deserves full respect for his job. I must say that he is one of the rare examples of how job should be done even if you have not so ideal workshop and tools. You simply must invest lot of skill, attention and care in what you are doing.
Great job mate!
Yo como hidráulico,lo veo bien ,e visto otros trabajos de el,con lo medios que dispone un trabajo impresionante
This is the miracle of the Indian economy (doesn't matter if it's not india). Lack of production capacity, only the industriousness of the people, hopelessness and golden hands
Exactly get the main a parts washer , t handle allen wrenches ,electronic parts cleaner and a radio to listen to fine music as he performs his work.
Excellent comment 😊
It’s the only spool valve mechanic I’ve ever seen, but I can still tell he is the best!!!
Зашёл почитать комментарии… спасибо поржал от души 😂😂😂
Простой рабочий человек с добрыми глазами. На таких и держится земля.
А кто будет реагулировать предохранительный клапан
Посмотрели бы Вы видео, где он гидронасос перебирает))))
@@user-fo5zc8em8h пружина👆
Ну вот, без наждачной бумаги всё собрал. Молодец 👏
Ах вот ты какой - механик гидрораспределителя...
Я догадывался, но о таком и не подозревал.
😁
Да охуенно парень работает! Аж помочь хочется, но я их только конструирую, а он потом их чинит)
этот пилять 40 годы наверно, чугунный притир🤦🏻♂️ давно алмазные регулируемы развертки есть.... да ещё и на такой скорости в горизонтальной плоскости 🤦🏻♂️🤦🏻♂️🤦🏻♂️, и чем он там микроны ловить будет?
@@TOLOBAIKIN , согласен, но что делать, если других возможностей нет…
This is the same guy that refurbished the hydro ram! What a pro!!
This gentleman does a brilliant job , and so relaxed 👍🇬🇧
Glad you enjoyed it.
Миксер мне в глаза но я смотрю его только из-за его спокойствия а не из-за навыков ,несмотря на критику со стороны аудитории в их сторону они делают свою работу пусть даже и не качественную но работу по улице не шлангуются дурь не шмаляют фанфурики не пьют,обычный человек который любит занятие и получает удовольствие от проделанной хоть ненастолько качественной но работы.
миксер?😂😂😂😂
Они этим деньги на жизнь зарабатывают, им не до срачей в комментариях
Обычно эти распределители выкидывают и меняют на новый. А в пакистане все восстанавливают мастера...
@@user-pi6ss4fd9f на видео Пакистан? Первый раз вижу этот канал
@@user-pi6ss4fd9f так он переходит новый👆👆
ещё одно прекрасное видео!! И чего то да, обошлось без наждачки.
It's fun to watch someone who is confident in what they're doing. Good job !
даже они не используют гвозди вместо шплинтов :(
Ах ты "Рыбий глаз"! уже от насоса к распределителю добрался!
P.S. Золотники наждачной бумагой не притер! Вывод - работать не будет!
В твоём колхозе лучше. 😂
Прям комент в тему!😂😂😂😂😂😂😂😂
В этом видео уже в ботинках-видимо это действительно выгодное занятие.А чинит он деталь не от Боинга737? Талантливый чувак.
да это пиздец
С таким талантом и я могу поменять колечко резиновое на каком-то клапане из-за которого скорее всего и уходила жидкость. А вот притереть посадку поз золотник это конечно нужен "опыт". Золотые руки чё сказать 🤣
This guy is excellent, I’m very impressed simply because I never thought these valves could be repaired, obviously I was proven wrong. Excellent work and I really enjoy watching your channel!!!!!!
Wow, thanks!
It’s amazing they do all this work without using ratchets.
dude looks cool and kind
me encanta su tranquilidad, y como tiene todo ordenado, cosas que otros no hacen
Can you imagine what this guys can do with the fancy tools?
I have seen him on a few videos; he does great work. I hope he does not hurt his head too often on the H-beam supporting his storage space!
Grande,lavori che da noi nemmeno si sognano di fare e poi impressiona la tranquillità e la manualità di questo ragazzo,bravo!! Saluti dall'Italia!👍👍👍👋👋👋
Видюшки конечно занятные, но самый смак это названия этих самых видео... ЭТОТ ТАЛАНТЛИВЫЙ МАЛЬЧИК, ЭТОТ ТАЛАНТЛИВЫЙ МАСТЕР И ПРОЧИЕ-😅😅😅
Строит сварочный завод)))
Этот молодой мастер, механик))
I'd happily let this man repair my car or truck.
Видите, Балаганов, что можно сделать из простой швейной машины Зингера? Небольшое приспособление - и получилась прелестная колхозная сноповязалка.
Да уж , Антилопа отдыхает ...
Гидрорегулятор притертой частью зажать в тиски, да он профи вселенского масштаба!! Как же так то???😭😭😭😭😭😭
Тоже об этом подумал
Да нормально! Хорошо хоть гнутым электродом не наварил и болгаркой не обточил
это регулируемый предохранительный клапан, а не гидрорегулятор. и он зажал его НЕ рабочей стороной. "рабочая грань" у него снизу на торце.
так что он все норм сделал.
No entendí lo q comentaste😭😭
A master of maintenance.Thanks to share.
You are welcome
Not one thumb up,BUT TWO THUMBS UP.GREAT WORK GUY!!👍👍
The work is marvelous
Merci et bravo,quel plaisir de te voir travailler avec autant de maîtrise,respect.
A man who don't need a snap on toolbox with $39,000 in tools.
Excellent work.
he is very talented
Muito bom amigo ótimo trabálho!! Parabéns....feliz ano novo👏👏👏👏🙏🙏🙏
From México, this is to be artesano, That 1st World wont have.
Trabalho super bem feito
Please remove bottom banner after a time. My eyes keep look at it, I can’t focus on your video clip.
Zoom your video to 1.2% completely removes it
Eres especial
Te felicito
👍👍 You are an artist 👍👍
Hi from Australia, I really enjoyed the content of your video and the skill you demonstrated, I like hydraulics and found your channel very interesting. Thankyou for posting
What are you using for a cleaner
Hi. Dear thanks for your precious videos!!!!
МЕХАНИК ОТ БОГА У НЕГО ЕСТЬ СМЫСЛ В ЖИЗНИ.
Se ve un buen trabajo, mi consulta, ese liquido que le aplica para ver el comportamiento y limpieza de la válvula que es?.
Very very good job!
Honestly I think I’m dumber for having her watch this video
Awesome !!!
Great job mate. 👍🇦🇺
А вы представьте что будет, если дать ему гайковёрт и шуруповёрт
да он в день по 20 таких будет делать
А если ему встать за хирургический стол?
@@user-dm2lu9vp2j не сможет стать .потому что они все на кортачках делают..
@@myrmyrmyrc 🤓
Good job checked his work before starting and after.
Excellent job my friend...
great work
А давление кто будет настраивать? Пушкин?
Excelente canal te felicito.
Top notch job! 👍
Honestly, this would be entry level hydraulic repair in the U.S.
The type of work you'd see from any beginner hydraulic repair technician
Muito bom o seu trabalho tenho vontade de fazer isso também
Tente deve você pode fazê-lo.
Estos mecánicos están hasta las pelotas de arreglar pistones y válvulas. Les das una grifa y hacen maravillas.
Superb 👏🏻👏🏻👏🏻
Beautiful!
Thank you!
Excellent video!
Thank you very much!
Superbe travail calme saint propre merci de montré se savoir
Good job 👍
lapping the bore would increase the spool clearance and cause more leakage ! Only if you fitted and lapped a over size spool would this method improve things. The only reason it held fluid after was the assembly oil viscosity stopped the flow. The clearance of the spool to the bore is worse than before. If I am overlooking something here I would love to hear it !
He used a larger spool from his big collection of spools. see @2:28 where he measures and chooses a suitable oversize spool.
Can this job be done without having to lap the bore? Im looking at fixing the same on a backhoe.
Super !
Molto bravo ,concentratissimo e non spocchioso come siamo noi!!
اخي انك مختص وفنان احترامي لك الكبير بانني ميكانيكي انت بارع وممتاز ربي يثبتنى بالعقل وربي يحفظك سلام
Ахуеть. Просто пассатижи и шестигранник. Ни воротков, ни трещеток, не говоря уже о динамометрическом ключе. И на вид делает работу аккуратно. Respect!
P.S. интересно, что там в бутылке: растворитель или бензин?
Very good.
Замена золотников и полировка каналов, считай новый распределитель. Спасибо за видео.
Sar bahut badhiya jankari
Great job.
Stay connected for more.
Beautiful 😍
TUTTO NEL PIENO RISPETTO DELLE NORME AMBIENTALI E SUL LAVORO 💪💪💪💪👍👍👍
Прям добротно отремонтировал
Nice work!
Thanks for the visit
И так сойдёт!!!! Сколько это отработает? Зато всегда заказы.
very nice
Muito bom
Esses cara são fora de sério mano
perfekt , top work
Bravo pour votre travail 👍🏼👍🏼👍🏼❤
Complimenti, sei molto bravo e professionale
Felice che la pensi così.
Тут хотя бы похоже на нормальный ремонт. Я думал будет по классике - пошоркать прецизионные поверхности наждачкой, и покрасить снаружи - вот и весь ремонт...
Great job, Master!?!
Rock on!
اعطاك الله ااصحة والعافية
Молодец!
Zabardast
Awesome
..... 🇮🇹✌️👍
Show 👏
Найти ремонтный золотник в продаже в России это будет чудо!
Они там их сами клепают в соседней токарке😆
На камазе есть ремонтный участок занимаются ремонтом и обслуживанием распределителей ,точат если нужно новые залотники и хромируют при установке ремонтных размеров.
Bravo.
К этому мужику у меня два вопроса:
1. Какого хера он в ботинках?
2. Где обработка деталей наждачкой?
Very good job
So nice of you.
Thank you! Cheers!
Amazing
Thanks
Bạn phục hồi bơm rất tốt thật tuyệt vời
vui vì bạn thích nó.
Agame un favor comoago para quitar una fuga en racor qestan en un banco de balbula en una máquina qe ya no consigo las arandelas orijinales qeson encauchetadas
why am i chilling with this video???! :| amazing with me :c
Bom dia meu amigo vc tem vídeo armando comando da retro 580n