Thanks for the video. I am from Nigeria, and this video has helped me to fix my w203 c200 Sun roof problem at no financial cost. Thank you so much for posting this
First, you don't need to remove the roof liner, in order to access the motors and gears.There's enough space for the fingers and screws over the central console, and all you have to do is to pull it down and be patient. Second, tightening the gear in best case is just temporary solution. It creates more friction on the gear and motor, and that may result in total malfunction. Often the lid is also damaged, due to the pressure which is generated from the damaged gear, trying to "escape" the box. Don't forget, that when the gear is damaged, the surface which it has scratched with must be damaged too. I'm talking about the steel cables. You can easily change the lids and gears, but changing the cables is a totally different story.
Nice video. My roof is not working for many years as dealer quoted $$$ but after watching this video I am thinking of fixing it myself. I have just one question, how do you remove those connectors from OCP. I just can't pull them out. Does it need any special tool to remove them.
👍 Many thanks Buddy. Due to your vid I managed to fix the exakt same problem by using a gasket of a bathroom faucet. Cost me about 2 hours of work and 5 Cent for the gasket, but saved at the end approx. 400,-€ 😆
All i have done was to change the gear and the lid from the sunroof with the curtain ones, which has no tension like these on the sunroof and respectively are far more preserved in contrast to the others. Lubricating the cords and rails is needed for a smooth and lasting operation either.
Thanks crazymandance and weichen I have a 3D printer and went straight for that as a solution. However, my printer was not connected to the internet so started reading the comments. Swapping the gears takes a few extra minutes but is the best engineering solution. Agree there may be room to do it with the roof liner in place but it is fiddley an I am sure I would have dropped a screw in the liner and then had to remove it later. Also as a safety point, the side impact protection system is in the A pillar cover so take care. I removed the battery terminal in the hope that the SIS will be dissabled (not sure it is so treated as live).
My sunroof stops just before the plastic part that moves down. And I can only close it if I manually push that wide plastic part down with something. Any idea how to fix it? Thanks
Před 7 měsíci
Can you provide a link to your 3d printed washers on ebay?
Do you a video tutorial for how to change the clip or button? (Open and close) mine broke I got a replacement but been trying to find a video tutorial. For just the clip. Thank you
Hallo Weichen, I bought a few days ago a w203 C class Sportcoupe, I manually closed the panoramic sunroof, I had the same noises. Even mercedes did not know how to fix it. Can you tell me where I can buy this parts from you ? thank you.
@@dinnoo89 it shows you how to close it manually in the car manual. You remove dome light, you should have a crank tool that looks like a s shaped allen wrench or use a 25 torx screwdriver. Left side is to open/ close sun roof and right side is to open/ close shade.
#KreativeFragen Hey ich habe eine wichtige frage im Internet find ich nichts gescheites weswegen ich an dich gedacht habe. Ich habe damals windows 10 auf eine 128gb ssd installiert aber mittlerweile mit treiber und soweiter ist diese voll und manche treiber updates gehen dann nicht mehr.... nun will ich windows 10 von dieser ssd auf meine 2TB ssd rüber installieren ohne den pc aber neu aufzusetzen wie mach ich das am besten bzw auch gleich mit dem update auf windows 11 ? danke im vorhinein
hi , my suroof small gear is broken but cannot put as if i buy only gear will not be able to insert as top of the shaft is wide so if i even buy only gear from ebay then its wasted . any suggestions would be helpful...
Hello my c300 2010 sunroof is stuck tilted up wards in vent position. I tried manually it just kept twisting . I clicked the button and it spins the bolt . So I did it for no reason. What do you have in mind
Thanks for the video.
I am from Nigeria, and this video has helped me to fix my w203 c200 Sun roof problem at no financial cost.
Thank you so much for posting this
First, you don't need to remove the roof liner, in order to access the motors and gears.There's enough space for the fingers and screws over the central console, and all you have to do is to pull it down and be patient.
Second, tightening the gear in best case is just temporary solution. It creates more friction on the gear and motor, and that may result in total malfunction. Often the lid is also damaged, due to the pressure which is generated from the damaged gear, trying to "escape" the box. Don't forget, that when the gear is damaged, the surface which it has scratched with must be damaged too. I'm talking about the steel cables. You can easily change the lids and gears, but changing the cables is a totally different story.
3D printing FTW! Nice video sir
Thank you, really helps
Thanks a lot, works Pretty good now
Nice video. My roof is not working for many years as dealer quoted $$$ but after watching this video I am thinking of fixing it myself. I have just one question, how do you remove those connectors from OCP. I just can't pull them out. Does it need any special tool to remove them.
Do you have a tutorial on how to replace a GLK 350 Front roller assembly? The dealership want $1500 plus tax (parts and labor) to repair.
Thank you brother!
Thanks for info and time.
Thank you. Where is the link to EBay for spacer?
Thank you well done 👍🏻
Nice sharing and tutorial..
👍 Many thanks Buddy. Due to your vid I managed to fix the exakt same problem by using a gasket of a bathroom faucet. Cost me about 2 hours of work and 5 Cent for the gasket, but saved at the end approx. 400,-€ 😆
I'm glad to hear that buddy!
Hi there, have you got the dimensions?
Do you have any of the 3D washers left. I looked on EBAY, but did not see them...Thank You highly informative video.
THANK YOU MY FRIEND
Great video
Hello, can you share the 3d printed dimensions of the washer ?
Thx
where is the link for the part on ebay?
Thank you so much !
Hi, I am trying this method on my w211. I am from the U.K. Any chance you can send the the srt file so I can 3D print the spacers? Thanks
Hello, can you share the 3d printed dimensions of the washer ?
All i have done was to change the gear and the lid from the sunroof with the curtain ones, which has no tension like these on the sunroof and respectively are far more preserved in contrast to the others. Lubricating the cords and rails is needed for a smooth and lasting operation either.
Hey. Did you just replace the gear from the right motor (curtain) to the left motor?
Thanks crazymandance and weichen I have a 3D printer and went straight for that as a solution. However, my printer was not connected to the internet so started reading the comments. Swapping the gears takes a few extra minutes but is the best engineering solution. Agree there may be room to do it with the roof liner in place but it is fiddley an I am sure I would have dropped a screw in the liner and then had to remove it later. Also as a safety point, the side impact protection system is in the A pillar cover so take care. I removed the battery terminal in the hope that the SIS will be dissabled (not sure it is so treated as live).
Do u have any idea for Volkswagen Tiguan panoramic sunroof? It stuck no back no forward !! Please let me know about it, bundle of thanks
hello, could you please share the dimensions of the spacer? thank you!
Nice, thanks
My sunroof stops just before the plastic part that moves down.
And I can only close it if I manually push that wide plastic part down with something.
Any idea how to fix it?
Thanks
Can you provide a link to your 3d printed washers on ebay?
I need some washers !!! How much for em i need em asap !!!
Hello, do you have a Link where to buy the 3D print part?
Do you a video tutorial for how to change the clip or button? (Open and close) mine broke I got a replacement but been trying to find a video tutorial. For just the clip. Thank you
Let me take a look at that and get back to you later
Hi, please tell me what diameter of the washer you used to lift the mechanism.
How long did this repair last?
the washer is on ebay
Merci beaucoup
Hallo Weichen, I bought a few days ago a w203 C class Sportcoupe, I manually closed the panoramic sunroof, I had the same noises. Even mercedes did not know how to fix it. Can you tell me where I can buy this parts from you ? thank you.
Nico, may be the simplest way for this is to use the metal ring from a keychain, that should work as this spacer. Hope this will help you. Best.
I have same problem clc 2008 parnomic roof stop working mottor is working but is not close
Grrat video, thank you!! Xie xie!
Hey how you doing bro I wanted to get those 3d printed spaces you are selling on ebay. Can you send me the eBay link so I can purchase some please?
What is your website
Can you please send the 3d dimensions ASAP this will be well appreciated. 👊🏾
Can you please send me the sizes of the washers for this fix ASAP. Thanks
Need these dimensions like yesterday. Please help
Same happened to me , now the roof is closed only on 1 side and other is slightly open , what to do? Please advise
You can close it by hand. Just need to remove mirror ang then with torx press hard on screw and then rotate
@@dinnoo89 What we need to remove?
@@dinnoo89 it shows you how to close it manually in the car manual. You remove dome light, you should have a crank tool that looks like a s shaped allen wrench or use a 25 torx screwdriver. Left side is to open/ close sun roof and right side is to open/ close shade.
#KreativeFragen
Hey ich habe eine wichtige frage im Internet find ich nichts gescheites weswegen ich an dich gedacht habe. Ich habe damals windows 10 auf eine 128gb ssd installiert aber mittlerweile mit treiber und soweiter ist diese voll und manche treiber updates gehen dann nicht mehr.... nun will ich windows 10 von dieser ssd auf meine 2TB ssd rüber installieren ohne den pc aber neu aufzusetzen wie mach ich das am besten bzw auch gleich mit dem update auf windows 11 ? danke im vorhinein
Can you tell dimensions of the washer?
Hello, you have a dimensions? Thx
M8nes like this scared to take it to bits might give it a go though
can you share the 3d printed washer ? i want to print it
Hello, you have a dimensions? Thx
Hello
I News the spacers!!
hi , my suroof small gear is broken but cannot put as if i buy only gear will not be able to insert as top of the shaft is wide so if i even buy only gear from ebay then its wasted . any suggestions would be helpful...
Hello my c300 2010 sunroof is stuck tilted up wards in vent position. I tried manually it just kept twisting . I clicked the button and it spins the bolt . So I did it for no reason. What do you have in mind
Bro what are the dimensions? Help Asap
Where you get the o ring
@@Samcity1000 do you know if the motors are same in the all cars. I have w211
@@dinnoo89 yeah the w211 and w203 have the Same motor
1:34 Those roof handles break easily. I went to 3 junkyards but still broke all of them. Guess I'll just have to order them off of Ebay...
Those were new teeth you installed
Can u give me ur eBay name so I can get the washer
Wo kann ich die kaufen
www.ebay.de/i/392779526731?chn=ps&norover=1&mkevt=1&mkrid=707-134425-41852-0&mkcid=2&itemid=392779526731&targetid=900308097017&device=c&mktype=pla&googleloc=9041847&poi=&campaignid=9867118506&mkgroupid=99713680309&rlsatarget=aud-507143380763:pla-900308097017&abcId=1145982&merchantid=7770842&gclid=Cj0KCQjw2PP1BRCiARIsAEqv-pTgL_JcfmQ4O5EXc9LWzOd5RnwuH7Wa58DESzDtotFMvm4pakSvHN4aAnWYEALw_wcB
@@Samcity1000 Da ist aber kein w203 dabei. Ist das das selbe?
Can you sell me the spacers?
I need some washers