How to Replace Valve Cover Gasket 2006-12 Ford Fusion
Vložit
- čas přidán 13. 09. 2024
- Shop for New Auto Parts at 1AAuto.com 1aau.to/c/137/V...
Valve covers will begin to leak oil when the seals eventually break down. A new valve cover gasket set will make sure the oil stays inside the engine where it belongs! This video shows you how to install a new set of valve cover gaskets on your 2006-2012 Ford Fusion.
• Check here for more videos on the 2006-2012 Ford Fusion: • Ford Fusion 2006-2012 ...
This process should be similar on the following vehicles:
2006 Ford Fusion
2007 Ford Fusion
2008 Ford Fusion
2009 Ford Fusion
2010 Ford Fusion
2011 Ford Fusion
2012 Ford Fusion
Tools you will need:
• Pocket Screwdriver
• 10mm Wrench 1aau.to/on/1AXA...
• 10mm Socket 1aau.to/oF/1AXA...
• 22mm Socket 1aau.to/oc/1AXA...
• 8mm Socket 1aau.to/oF/1AXA...
• Trim Tool Set 1aau.to/op/1AXX...
• Needle nose pliers 1aau.to/oh/1AXA...
• Needle nose pliers 1aau.to/oh/1AXA...
• Ratchet 1aau.to/oX/1AXA...
• Socket Driver
• Socket Extensions 1aau.to/oI/1AXA...
• Torque Wrench 1aau.to/oD/1AXA...
• Brake Parts Cleaner
• Paper Towels 1aau.to/oi/1AXS...
• RTV
• Pick 1aau.to/og/1AXA...
• Razor Blade / Gasket Scraper 1aau.to/of/1AXA...
• Rubber Mallet 1aau.to/oa/1AXA...
Subscribe: / @trq
Check out our playlist:
Ford Fusion 2006-2012 1st Generation: • Ford Fusion 2006-2012 ...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts
√ *Do it Yourself*
√ *Save Money*
The link doesn't work.
What about the back valve cover? That's the hard one! Video on that one please!
Great video!! Thanks for the help. Saved me $460
This is a great video. The only issue is that the torque sequence needed to be put on the full screen to read or screenshot it from the video.
Great video! Nice job explaining everything. Thanks!
do you have a resource for identifying the sequence for torquing the rear valve cover bolts?
45 degrees, and a quarter turn are not the same thing. The intake bolts were over tightened in this video.
Thank you for the video. I'm not looking forward to this.
Do you even have to take off the intake manifold?
Great Video. Thanks.
Excellent video! this seems way more difficult than a 2011 Fusion.
Is this a 6cyl?
Does the kit come with the o rings
you should replace both valve cover gaskets
What engine is this?
What is this , a SHO Fusion???
My engine looks different n it’s a 2008 that vvt seal went in easy mines don’t even fit
“Next we’ll disconnect this clamp right here”
Proceeds to show a close up of a clamp that’s difficult to locate due to the poor camera work.
Back
he put the VVT seal in upside down in this video just fyi
zooming in on his fingernails doesn't let us see what he's working on. Sure it's great to see how to remove a clip but WHERE is the clip? Can't tell cuz of the super close zoom. Epic Fail.