Video

Where is the empro_basic library to be found?

Dear Engr. Thank you for such an incredibly educational video. I need assistance with my unit cell design in HFSS for RF energy harvesting. I want to co-simulate the rectifier for the unit cell in both ADS and HFSS to evaluate the energy harvesting efficiency. Could you please guide me on how to do this? I would greatly appreciate your help.

hello, thanks for the video. Can you show me how to import txt or csv file in ADS? I want to plot my measurement data directly and compare with my circuit simulation done in ADS. And be able to see if the tuning fit my measurement datas. Best regards

You're talking about waves and spheres. Not one place on the web that puts those together with rhumb lines. You see that, right? We doing something wrong?

The explanation is too fast, and the pronunciation is difficult to understand.

Also, how do define the port? can we select all pin in the PCB as port for the extraction? or just input and output pin?

Hello thanks for the video, after running the simulation what are the following step to verify extraction is good?

Thanks for this video Do you have online tutorial for PEPRO user?

Great video. Thanks for sharing.

Could you share the ADS simulation file please?

I use N904B which support 2 Hz to 110 GHz, can downconverter be omitted?

Hello! When I plot output harmonics for this particular simulation. It only shows fundamental

Chinglish

is the H transfer function and S21 dB result same? if we perform on the same circuit?

Iyi

I have a few questions. Is there a way to contact you?

Where can we find this example project?

What is the value of Vp and Ip?

请问这里的Vp和Ip是多少啊，怎么计算峰值

i could not download it for trial. what I can do ?

thank you very much

I am not able to generate a new schematic. Those options are seem to be disabled(shown in Grey). What can be the possible reason and how to overcome it?

kemet电容怎么在ADS中正确导入

ADS got rid of the S1P making it impossible to view my antenna measurements. Maddening!

Hello, first of all, thanks. On the other hand, I have a doubt, what is the main difference between a symbol and a hierarchy design?. Regards.

Hi, good day, thank you for the video, I have a question, is it possible to design a circuit from the response curve? I have the S11 graph with multiple attenuation peaks at different frequencies between 8 GHz and 12 GHz that can be considered as a low pass filter and I want to get the circuit that describes that response but considering the position of the peaks and the maximum values of attenuation. Thank you in advances for your help.

Hi, good day, thank you for the video, I have a question, is it possible to design a circuit from the response curve? I have the S11 graph with multiple attenuation peaks at different frequencies between 8 GHz and 12 GHz that can be considered as a low pass filter and I want to get the circuit that describes that response but considering the position of the peaks and the maximum values of attenuation. Thank you in advances for your help.

NLFM cannot be measured on a spectrum analyzer. What instrument do I need to measure NLFM?

How to do automatic extraction of parameters?

This is a good content. Thank you for sharing!

please do for "Outphasing Power Amplifier" too

Thanks for helpful

Hello, How can we please add dielectric blocks into a dielectric substrate ???

Thanks for helpful

Is there a guide for ADS setup workflow when using a design from KiCad EDA?

Hello! The link you shared is no longer accessible. Could you please share the workspace via a new link? Thank you very much.

Is there an example/demo project for the via transition available for ADS?

Really good movie

can you send me book about hardware? thanks a lot

So difficult to understand.......

Hello Mathew Sir, While computing NDF using WSP probes (at internal nodes of the devices, also ensuring ckt passivity when device is off), the encirclements for NDF is coming negative ( < -1) . What this represents ? Is ckt unstable in this case? Second doubt: Apart from perturbation frequency sweep ( small signal frequency sweep), shall not We sweep the signal frequency spanning over MHz to fmax of device ( although ckt passband frequency is very narrowband ) ?

Differential TDR?

😂😊

i need the marital please

Could you please explain how to set NDF Probes?

Hi， How do i get the imp of current source plane?

Did I get it correctly? The V_Probe instrument simply does not work like the I_Probe in Transient; and you have to use labels instead. So what is the use of V_Probe? A deprecated tool not removed for the version compatibility?

Thanks so much!!!

Hi Matthew, do you think it is possible to use a class E topoly for pulsed radar application ? I mean if it possible to pulse the class for examplo with 10% of duty cycle and 1KHz of prf.

How to enable SCPI recorder in my N9030B PXA?