Video

Milwaukee C18HZ repair Today I fixed the same saw that I paid $1 for. The machine worked unevenly (fast/slow). I washed the master switch in alcohol and blew out the switch with compressed air. Now it works like new! Greetings from Switzerland

I have the m18 model. The issue is that the blade has too much left and right play. I cant get an accurate cut because theres so much blade wobble.

Very nice thank you

Promo_SM

Great video, and thank God it's not hard to take apart! The problem is the oil they use from factory I believe, or just the amount that they use. Can't believe you need to "upgrade oil" nowadays, but that's what it's come to lol. It's a great tool, but mine rusted shut as well. Freed it earlier today. Opting for some pneumatic oil to prevent it again. That stuff keeps my Ingersoll impacts in working order, so I trust it!

How many hours a day did you run it? Sounds like the bearing. I bet if you open it up you could replace that bearing

Always spray the chuck with penetrating oil first! You shouldn't need to take it apart.......Mine was Rusted shut, and just sprayed it a few times and worked the Release wheel, and came free. Mine was under water, Rusted shut....and oil still worked.

Thx for the info, made me squirt some lubricant into it and it loosened it up!

Helpful, sort of, video too zoomed in really but probably can do this.

The cap on my pin is completely crushed so they sell that separately?

Maybe I'm stating the obvious but I would suggest only taking apart the chuck as a last resort. FIRST, try a generous dose of WD 40 on and inside the chuck itself. Give it a minute to soak in. My reciprocating saw had a stuck chuck but lubing it well saved me the time of taking it apart. --Mr. Obvious

The problem is I have a blade stuck in it. It wont turn completely to release the blade.

Saved me from sending it in lol thanks

You gotta be kidding me on a new tool not used very much...my hackzall is stuck! Never had this problem on any other sawzall!

My saw blade is stuck in the Haxkzall due to the lock won't turn to release it.

Thank you.

Easier to take plastic housing apart and blade guard off to start with; it makes puttting it back together easier when dealing with the pin. Body hosing screws are T-7 or 8. The blade guard screws are T-20. It also allows you to clean the debris inside the housing. I spent over an hour trying to put the pin in; spent 20 min taking it apart and putting it back together.

Don't ya just love working on tools that you need to work on work stuff with?

The left front burner does not click at all but when holding one of the other burners on that clicks and you hold the left front burner on the other burner lights the faulty burner.

Left front burner does not spark at all you can hear the gas coming through but no click what so ever please help.

Such an exciting video LOL….Jokes aside, thanks for the info. I’m about to get it a try….

thank you sir - helped me down in tx!

Even after expanding the picture I had trouble seeing the parts. This made this video less than helpful to me. You might want to consider improving your lighting setup so things are not lost in the shadows.

I couldn't find a removable retainer clip to save my life. I finally opted for good ol' WD-40, which worked quite well. No doubt though, your method gets to the heart of the problem, and I wish I could have done that instead. Just couldn't find any separate removable metal piece on the end of the blade assembly. A close up of that portion of your tutorial might help.

I was glad to find this video. My Quick Loc failed by locking up. The problem is that one corner of the square flange on the pin broke and it jammed the mechanism. Getting the locking ring off requires a strong tool. I broke a couple small screwdrivers. I was successful with a sculpting tool. Others use a pick. The part in this reassembly where the pin is replaced glossed over what was the hardest part of the repair for me. It took 6-10 tries at reassembly before the collar that guides the pin would seat low enough for the 1mm flange to clear it so as to be fully inserted. Getting the bottom, spring, sleeve and collar low enough on the shaft is the trick.

I want to buy this for my kitchen counter top , how and from where I can buy?

Waterproofing a waterproof board makes no sense......

Hydroban not to be used. The GoBoard with Pro Sealant (or equivalent) is waterproof as is. You will not get good tile bond to goboard with hydroban.

Why not use the GoBoard Sealant? Also besides waterproofing what was the objective?

Thanks for this demonstration!

Do you work in constrution industry?

Good day to you sir. I am James from Manufacturer of Quartz surfaces in Vietnam. Do your company doing import quartz slabs . I would like to share you our more information n our quotation if your side interested in ? Supply Quartz Surface,Manufactured&fabricated in Vietnam,Tariff Free to the USA. Phone:+84 961831556

Thanks for posting this video. You helped me fix my Smeg and save some money. :)

*Nice to be able to buy an oven at a normal price hat is focused on delivering heat where it is supposed to go instead of just looking pretty.>>>**allmy.tips/myms** This oven is engineered around the burners which are superb. One turns a knob and gets beautiful blue bundles of burning gas. Another knob turn and the stove turns on. Want convection - rock the convection switch to on. If you want to cook - get this range. If you want to sit around and tell people how you can program your oven to come on when you are not home - well - get something else.*

Thanks for sharing. Too many quartz choices! How many inches is the mitered edge? thank you.

Fantastic. Looks awesome. Now all you have to is change the floor, cabinets and stove. Thanks for sharing!

Il, manque le point le plus chaud et le point le plus froid sur cette flir one pro