![rsy](/img/default-banner.jpg)
- 111
- 311 909
rsy
Philippines
Registrace 1. 09. 2019
LIFE ISN’T SHORT YOU JUST NEED TO DO MORE.”
Video
Car toy made of straws and 4 bottle caps
zhlédnutí 33Před 2 lety
Car toy made of straws and 4 bottle caps
voltage regulator 7-40volt in, 1.23-37Volts 3ampere
zhlédnutí 406Před 2 lety
voltage regulator 7-40volt in, 1.23-37Volts 3ampere
part3: how to calculate series- parallel resistor in a complex circuit
zhlédnutí 310Před 2 lety
part3: how to calculate series- parallel resistor in a complex circuit
step by step tv led repair with power but no stanby power no video display
zhlédnutí 94Před 2 lety
step by step tv led repair with power but no stanby power no video display
mini karaoke repair just on for a few second then will be off what the problem?
zhlédnutí 185Před 2 lety
mini karaoke repair just on for a few second then will be off what the problem?
part 1:how the tl494 ic work with circuit test demonstration
zhlédnutí 7KPřed 2 lety
part 1:how the tl494 ic work with circuit test demonstration
top 5 electronic circuit animation how it works
zhlédnutí 3KPřed 2 lety
top 5 electronic circuit animation how it works
how the street light work animation,automatic light on,ldr sensor
zhlédnutí 973Před 3 lety
how the street light work animation,automatic light on,ldr sensor
how the automatic street light work(opto coupler,2n3904,moc3062)
zhlédnutí 912Před 3 lety
how the automatic street light work(opto coupler,2n3904,moc3062)
full detail on How the ac wireless tester work(2n3904)
zhlédnutí 1,1KPřed 3 lety
full detail on How the ac wireless tester work(2n3904)
I'm sorry, WHAT??! All i hear is elevator music......
I'm sorry, WHAT??! All i hear is elevator music......
Finally someone attempts to explain WHY the output can change his state, every single video on youtube just throw formulas but no one explains that when the capacitor is full then it makes the variation of voltage needed to switch the circuit Thank you
Does anyone know how to ask questions or make requests politely? Apparently not. If this were my video I would block any impolite user.
Nicely done! That was exactly what I was looking for. Now I need to see how you made an inverter for the LEDs.
hello what is the name of this diagram?
Very nicely explained mate, thanks for sharing
How to connect latching circuit and npn of ir receiver? Example push button connection
Thanks a lot.
if passcode is 1234 then 1 (134 any ammount they not reset) 2 (124 anu ammount they not reset) 3 (123 anu ammount they not reset) 4 open sesame only 1234 matter but between can push those other button when pin is low and it connect clock pin that allready is low. nothing happen so you can push (1)134141(2)242412(3)321213(4) amd it work this is example movie door lock. open keypad hook power to any pin and test. if you hook pin 10 open sesame. none of other pins actually not matter to make wrong passcode work with those 1234 need hook that button to reset with inverter if pin is low then its wrong number and it reset. meaning pullup resistor to and feed gnd to other buttons. then pushing wrong key that is low change reset pin state and reset if it correct key then high not do nothing than step to next. if that not work we need invert that wrong 0 button to high and use same circuit. now its better keypad only actual 1234 works so basically 4 input NOR gate with transistors and all input pullup. all input high it send LOW to reset like it is but when LOW from wrong sequence button come it send HIGH ro reset
51K not 51R!
For best result print twice or more on the same paper.
I’m confused is the password 3247 or 2134?
3247 are pin number from chip pin3 is output0 ->button2v(this is high after reset or turn circuit on so this is first digit button) pin2 is output1 ->button1 pin4 is output2 ->button3 pin7 is output3 ->button4 pin10 is output4 ->button5 OR this case its open sesame xD so your passcode is what button you connect those pins not matter there no labels LOL and sequence not matter if push only those numbers you eventually get it correct if passcode is 2134 you can push (134*)(2)(234*)(1)(214*)(3)(213*)(4) * means you can hit those many times it not make any diff it wont reset. so passcode is *2*1*3*4
there is a one mistake in a circuit diagram 5:43 there is 51 k resistor instead of 51 r in receiver circuit in ht 12 decoder ic ocillator pin
Noise is worst
What did you use to print?
It worked for me and I subscribed. Thank you.
Great work , whitch software you us for animation?
😭
telent
With these connection always leds turned on since they have power and the ground. Something is wrong with this schematic
Remove the background music unable to here properly
So nice thanks sir
Excellent video. I particularly liked the circuit diagram.
Please, how do you reset the circuit?
other buttons that connect reset pin 15 those wrong ones xD
Thank you !!!! 👍👌🕹
Where is part 2 where you explain inverting the output from HT12D?
A kolik to dá Ampér (když je tam ten odpor 1k)?
What program?
Its recommended to set the playback speed for this video to 1.5x !
Thanks 😂😂
Can't hear you bro. No music.
LOUUUUDER... the music PLEASE... LOOOOUUUUDER... I can't hear the music, CAN YOU HEARRRRRRRRRRRRRRR MEEEEE ????!
App reveal please 🙏
Sorry😥
Bagai mana cara menentukan hasil layut.ketika akan di tranfer ke pcb (menentukan ukuran pcb)
I don't understand
@@ABZTRONICTUTORIALTo what do you not understand
@@mudahko6681 your language
how move to other side?
Sorry sir 😭
Please give same tutorial on Kicad software
Sorry sir the owner is died 😭
Excellent tutorial sir
How to add components in own library sir
😭
Video super sir Remaining tools how to use pls one video
which software used to animation?
Is 150r on pin VT of receiver necessary? I watched other tutorial video where this pin is not used and it still works.
The decoder IC osc resistor value should be 51K if encoder osc value is 1M
How to add our own footprints or download, the library is very limited.
Sorry sir i dont know how
@@ABZTRONICTUTORIALTo você é um inútil cara!😆
Is it autocad electrical?
brother am sorry for this but actually you made a mistake. you reverse the VT led terminals I did same as you do here , the vt led, and the data pins go high in the absence of transmiter. # CORRECTION connect the vt led +ve to the ic the ground the negative.
thankZ3x..this tutorial godbless
thank you so much for this tutorial sir,its verry helpull for the beginers like me sir...godblees
i subcribe your chanel
Can stand the music, click out.
Either remove the audio or video
ditch the background music sheesh what the hell is wrong with u
Thank you