Video

@maicolherrera7685: "DCOM" means DEFAULT COM. Default Com is DF1. Once you change the Communication Protocol to anything but DF1, the DF1 light will be turned OFF. But what should be the communication protocol for the channel is the question for you. You can look into the other device that your PLC is connected to and find out what communication protocol and configuration it is looking for from your PLC. Hope that helps. Good luck

@@SYPHOANG cuando hago la descarga con la modificación del Chanel 0, el PLC me impide conectarme otra vez y por eso no me deja ponerle run

@maicolherrera7685: It's very simple. You pressed the button on the PLC to set the default DF1 to Channel 0, the DCOM turned ON. However channel 0 in the program you downloaded to the PLC is configured for DH485 or anything but DF1. My guess is DCOM light turned OFF after you downloaded the program to the PLC because channel 0 is now no longer set for the default DF1. You can no longer connect to the PLC because of the cable between your PLC and your computer. My guess is the cable you use is for DF1 communication protocol, it is not for the communication protocol for channel 0 in the program you downloaded to the PLC. I think that was also the reason you set the default DF1 to channel 0 on the PLC. If I was you, I would never reset channel 0 on the PLC back to DF1. My recommendation is to always find the right cable that works for the communication protocol configure in the PLC program before any downloads. Please consider joining my channel for more support. czcams.com/channels/yyYzqg0sp_W7CW9ScZh-zA.htmljoin

@vleiswalker9374: Glad it was helpful.

@user-fb9rd2dl4l: Unfortunately I don't think that would be possible. However you can look into your scada system to find out what communication protocol and configuration it is looking for from the micrologix1200 PLC. Then you can set it up again in the PLC logic. Good luck.

@khachapatrachatamethin7484: which document in my dropbox are you trying to download? The full links might be available for channel members only.

@khachapatrachatamethin7484: Are you Samroeng Kanathong who is trying to download the function block "Lead_Lag_STBY_BLK.7z"? If you can confirm it is you and that is what you need, I can share you this file only as an exception for a potential channel member. All function blocks are for channel members only. Please consider joining my channel for more support. czcams.com/channels/yyYzqg0sp_W7CW9ScZh-zA.htmljoin

@@SYPHOANG thank you so much. I can reach out to your document right now. I wonder how to convert XML file back to Excel file. Could you please help?

@khachapatrachatamethin7484: Are you trying to download the function block "Lead _Lag_STBY_BLK.7z" and import it into your PLC project in Connected Components Workbench? If so, you need to download and import the file with ".7z" extension into your PLC project. No need to worry about other files.

@@SYPHOANG nope.

@punishedgoy9131: Thank you for your support to my channel.

If we check the Expanded box at 1:06, how much can it expand? Isn't the maximum length of N File only 255?

@yijunhuang1005: Thank you for your support to my channel. Yes, it might be 255 max.

@yijunhuang1005: Glad it was helpful!

@T---dq2qv: In the "FactoryTalk View Studio", at the very top, select " Application", then click on "Create Runtime Application". Be careful to pick up the right version for the .mer file you want to create at " Save as type"? Make sure its version is lower than your HMI firmware. Good luck.

@Man_Arm92: You're welcome!

@simonngo7085: Thank you for subscribing to my channel. I have not tried it with any Allen Bradley PLC but I think it is very possible.

@punishedgoy9131: Glad you found it useful. Thank you for your support to my channel.

@punishedgoy9131: It is Secomea SiteManager 1549.

@@SYPHOANG please please please make a video on the site master

@punishedgoy9131: Thank you for your interest in the Secomea SiteManager 1549. Below video is what you might want to check out. czcams.com/video/Auy5b40LHgY/video.htmlsi=0uyJTLIuTSko2mhf

@T---dq2qv: firmware and software version are different. They are not exactly the same. The software is what is installed on your computer while firmware is what is installed on the controller. The key point is firmware version ALWAYS need to be higher than the software one. Hopefully that clearly answers your question.

@@SYPHOANG thanks you very much for this anwser , so the firmware version alway need higher than sorfware one , such as Firmware version is 20.019 and firmware version do not higher than 20 such as 21.00.00 is it right

@@T---dq2qv Correct.

@InstrumentacionExterran: No, this is "Connected Components Workbench" software.

@InstrumentacionExterran: ACD files are for Studio5000/ControlLogix or CompactLogix PLC's. This is Micro800's PLC that uses Connected Components Workbench for programming.

@YohDave: You can use "STRING" data type and get up to 82 characters for each tag.

@@SYPHOANG Thanks! Do you know how can I write the serial number in the tag? Or how can I link the tag with to the serial number?

@@YohDave From programming perspective, you create a "string" data type tag in the PLC program and then map it to the HMI for a manual data entry. I am not sure what you meant for "serial number"? Are you trying to connect your PLC to a barcode/QR code reader/scanner? If so, I am not familiar with these devices.

@@SYPHOANG Thanks!

@karthikvhiremath1886: This is the right video for you. But do you have all the information you need for data mapping? You need to know the IP address, subnet mask, the configuration of the power meter as well as its Modbus data mapping.

@@SYPHOANG Thank you sir... I got one fbd from your video for 2 WORD TO REAL converter FBD absolutely working ultimately... So I need one more Instruction REAL to 2 WORD CONVERTER... If you have please give me link....

@CongDucDinh-s6c: Bạn có thể tải xuống từ Rockwell Automation.com. Nó sẽ cho bạn thời gian gia hạn là 7 ngày để dùng thử. Sau 7 ngày, bạn sẽ phải mua giấy phép từ nhà phân phối ủy quyền của Rockwell tại địa phương. Đó là cách tôi có được phần mềm tại nơi làm việc.

@joaopaulopaul: ? Who is he?

​@@SYPHOANG precisando do software do GP 2301 proface

@hchangv: The password I entered at 2:15 was set up earlier (not in this video). When you first power up a brand new HMI out of the box condition, it will prompt you to create it. There is no such default password coming from Allen Bradley. If you lost the password or simply do not know it, flashing the HMI firmware might wipe out everything including the password to allow you to set it up again. Thank you for your comments.

@filimniko: No problem!

@tdezcooling-heatingandcraf207: I am not sure what you are looking for. Are you looking for the programming code?

@asifislam7376: Unfortunately I think it wouldn't be possible because Proface and Siemens are 2 different brands. The software is very different between the 2. You are on the right track but you will need to get the Proface software for what you need.

@arjunjayswal6347: You're welcome 😊

@arjunjayswal6347: You're welcome

@wandersonpereira9884: Glad it was helpful.

@peterjenkins886: You bet!

@ScottWilliams-u8l: Glad I could help. You can try to get it from Rockwell Automation website. However it is too old. I am not sure if it is compatible with Windows 10.

@user-fb9rd2d|4|: I am not sure what you meant for "date of destino"?

@testaccount-p8j: I am not sure what you meant for "virtual machine" but you can test the HMI application right on FactoryTalk View ME or window station.

@@SYPHOANG Thanks for the reply. I was doing an analysis on remotely updating the panelview device but right now I do not have the device. Just wondering if there's a way to simulate the panelview device on Windows.

@@testaccount-p8j : If you don't have the actual HMI, you will need to have the software. However, if you don't have remote access to the PLC, it still will not work.

@@SYPHOANG Thanks for the information. Will try to seek another way to do it!

@lifevideo7628: Glad it helped.

@craigandjomonk: Glad it helped.

@LonnieHeadley: Glad I could help.

@vladimirgp139: Unfortunately, I am not familiar with Modbus Doctor.

@indrakrisnabayu7377: Not all USB drives are the same. The newer ones that is over 32GB might come in exFAT or NTFS format that will not work with Allen Bradley HMI's. Please make sure it is formatted to FAT32. That might solve the problem you are experiencing. A while ago, SanDisk tech support recommended me to use the software named "FAT32 Format" from their website to format any external drives with any size to FAT32. Unfortunately, I don't keep the link to download it but you can ask them for the link. Good luck.

@mohamedelnikeb6982: I am not sure why your HMI configuration screen does not have the EXIT button. Not all Allen Bradley HMI's are the same. The firmware 5.10.00.09 you have on your HMI is likely for very old Allen Bradley HMI's. I believe this VNC viewer feature is only for those not too old. If you have the exact same HMI I showed in the video, you should be able to upgrade it to firmware v10. Please see the below video for the instructions to do it. Hopefully it will solve the problem for you. Good luck! czcams.com/video/3iAgL_yj8WQ/video.html

@pankajparihar8593: You might want to check the "length" set up on your Modscan32. It cannot be greater than the amount of Modbus registers coming from your PLC. Good luck.

@edvinasjablonskis2054: I am working for Allen Bradley. You should contact your local Allen Bradley authorized distributor to get it. Thank you.

@@SYPHOANG I contacted them, but they could not provide me this version of the software as its obsolete. I need it for the panelview 1000 hmi backup. Is there any way you could help me obtain this software?

@edvinasjablonskis2054: I am not sure where you are but I am in the U.S. and was able to get the. software from Allen Bradley website. I don't think the software version really matters. You can try to get the version that still available. Hopefully it will work out for you.

@punishedgoy9131: Below is the selection guide from Allen Bradley for Micro800 PLC family you might want to check out. The catalog number details are on page 4. Per Allen Bradley, "Q" is for 24 V AC/DC Input type. The first "B" is for 24V DC Source output type. The second "B" is for 24V DC Power supply. If you find this video and the below information helpful, a "super thanks" at the lower right corner is a great way to show your support to what I've been doing on my channel to help everyone. Thank you. literature.rockwellautomation.com/idc/groups/literature/documents/sg/2080-sg001_-en-p.pdf

@user-fb9rd2dl4l: I don't quite understand your question. Maybe the google translate doesn't do a good job. Would you please leave your comments or questions in English? Thank you.

@congnguyenuc1614: Cảm ơn bình luận của bạn. Đầu tiên, không phải tất cả HMI Allen Bradley đều giống nhau. Chỉ những chiếc Panelview Plus 7 sau này mới có nút vuông màu trắng ở góc dưới bên trái để chuyển đến màn hình cấu hình HMI. Đối với các HMI Allen Bradley cũ hơn như Panelview Plus 700, bàn phím USB là lựa chọn duy nhất để bạn thực hiện điều đó. Đây là từ nhà sản xuất. Nó không được thiết lập bởi bất cứ ai. Bạn có thể muốn xem video dưới đây. "super thanks" ở góc dưới bên phải là cách tuyệt vời để thể hiện sự ủng hộ của bạn đối với kênh của tôi cũng như trải nghiệm mà tôi đã chia sẻ trên các video của mình. Cảm ơn. czcams.com/video/UkpAesSynQw/video.htmlsi=um3462MEsAT8E1hZ

@ansonkiek6471: Unfortunately I never tried it before.

@Shubham_848Vlog: Glad it helped. Thank you for subscribing to my channel.

@corderodedios776: Glad it helped. Thank you for subscribing to my channel.

@erasmosanchezespinosa2739: Glad it helped. Thank you for subscribing to my channel.

@nukeelda: I am not sure what you meant for "the physical connection"?

@@SYPHOANG Rec. Video or picture of ethernet cable going to PC and PLC I know it is Ethernet because of configured drive for ethernet cable or RJ45.

@nukeelda: Yes, it is just an ethernet cable plugged into RJ45 ports on your PC and the PLC. Thank you for your comments.

@multika_fpv2269: Really? I thought it should be able to. If I have the controller 1100, I will test it out for you.

@@SYPHOANG In the io configuration On channel 0 or 1 There is no modbus TCP selection option

@multika_fpv2269: So I guess there is nothing we can do about it. In fact, this was long obsolete.

@aaron-yg/gy: I don't think it is possible.

@pedroborges2672: Data Logging might be what you need. czcams.com/video/g63NWaOARik/video.html