Video

❤❤❤❤ quedó muy bien

That paint job is stunning. Thanks for sharing.

Looks great nice work 👍🏻

Watched a lot of diy shop cabinet videos today, have not liked or commented on any of them ... until this one. Great idea. Best luck to you and your channel.

Can someone tell me why does it have to be completely welded in ? Why can’t you just spot weld most of it and then grind back make it flush and then put bondo over it?

I have a new 38351 Fitech system. The newest interface handheld works flawlessly. I agree that Fitech needs to put out a manual that spells out what each software tuning line item does! Bryan at Fitech has great basic video's, but that's where it ends.

Who welded the frame ? Retarded Frankenstein?

Excellent video!

I love the I have " no idea" to the random part you pointed out.

It kinda looks like those nascar toolboxes you see attached within the outside of those trucks. Pretty badass actually

What’s your ignition time in that and advance timing at ? Been having a hard time trying to get my time in.

Interesting idea! You know it can hold the weight, because those drawers full of paper would be crazy heavy. Looks like snapon made it themselves 😂

Are you still happy with Radiator? Any issues?

Hey that looks sick I love it!! Yeah I'm thinking about how to do mine on my Eclipse thanks for the ideas

I think our f100s went to the same body shop originally 😂😂😂

How's it going?

Very well done. My complements! I must say I and apparently many others did have that same thought - filing cabinet prices just went UP. Ah well...While walking the dog last week, just down the strett someone put out a Hon four door upright filing cabinet for letter size papers with a FREE sign on it. It is waiting for me to sand it and paint it. I, too, am going to use rustoleum white paint. This is for our business office. Anyhow, I am going to start looking for your style cabinet for my garage becuase I need to clean it up out there. Thank you for the video.

That’s pretty darned awesome

How are they holding up? Only reviews I found on them were pretty poor but reviews don’t tend to be very trustworthy. Probably msd employees writing them to justify their insane prices.

From the inside it sounds like a titan or a silverado.

I just stumbled on this video and the timing couldn't be better. I recently moved, at my old house I used an old IKEA dresser as my work bench with tool storage. It was a great way to store tools and it attached two 3/4 plywood to the top as the work table. However like many things that are IKEA, it lasted about 10 years from some serious abuse and wasn't up to be moved when we moved houses. So I tossed it, which I was sad to do because it did make a great work bench. However at my new house, the previous owner installed two work benches and they are solid. However they are only benches without any storage. So I have been looking at getting a cheap dresser for my tool storage. I couldn't find anything decent used for below $100 and below that it was just pure garbage. I didn't consider using file cabinets but I just looked on Marketplace and there are several of the same exact ones for $50 and I found one thats 2x2 with a work top for $100. So I think I know which way I'm going. Thank you for the idea.

It really does look great!

"Nice and CNC'd" Haha. Fit and finish does look great. Thanks for such an in-depth video. I usually double the price and it's fairly close. Worked with a milling machine, too.

Hello, I’m planning to swap my 1987 gxl Rx7 for a 302 mustang engine; I wanted to ask you if you changed the rear end in your car, and if you did, what you swapped it for?

The factory sealer on these trucks is terrible and cracks over time. The roof seam will let in water behind the drip rail. The low spot welds where the roof goes over the drip rail will hold water and the rust starts from there. If anyone is restoring one of these I recommend putting body filler in the lows and maybe slope it from the center. One tip is never grind down your welds completely, you can make the flat metal on the sides of your weld too thin. Just grind it halfway and beat it in slightly and bondo over it. You can also lap weld the new sheet metal over the old as long as it’s where the water runs down over the lap and you cut the old rust out.

Lose the background racket. I don't understand how creators don't feel the irritation?

I've got a crown vic swapped 56 chev panel truck and this is just what I need to get it down! Thanks!

Did you have any clearance issues with the Snap on badge?

Why would you use a Crown Vic rear end and not an explorer rear? I hope you either modified the perches for the skinny axle tubes. Are you going to narrow it? The track width has to be way too wide because the explorer unit is perfect for my 69 f100

Oooo. I’d like an update on how well it’s holding up. For example, are to get drawers still sliding well with all your tools in it or did you find that they’re too heavy to hold a bunch of tools?

Has snap on copied this, it’s been a couple of years since this video came out.😊

I got one for my race car to control everything with thermal switches so simple and so much cleaner. HALF THE COST OF FUCKING MSD TO

I have got a Pashley Sovereign, and I think that it looked better in a project like this

Paint looks fantastic. I bought a couple almost 20 years ago for $50/piece. I painted them red with black drawers like my Craftsman 42" bottom box. These bookend each side of my 42" box for a work bench and looked amazingly professional. I love the top slideout drawers. I made slider trays 1/2 the drawer width for all the rest. Store bigger stuff underneath the tray. It's unbelievable how much you can pack in these cabinets.

Ideally, the patch piece needs to bend 90* at the bottom so it sits flat in the bottom of drip rail, and spot weld it in.

No, it did not we pinning in plug diagram

Hi what tope o axe or year do you used

has the e6000 stuck well? Even in the heat? and freezing winters? worried about that lol

Does the baking produce a lot of fumes?

Should of tried lead solder for gutter.

Hows the welder doin

Good job my brother 👏🏽👏🏽👏🏽

Awesome job on the file cabinet I did the same with one from work they were going to toss out. Thanks for sharing video.

Don't worry I'm sure nobody wanted to see the steps in between

Great job!! I have four 3 drawer lateral file cabinets in my shop/garage. I'm actually going to set them up and incorporate them in a miter saw station. Now after watching this I guess I'm also going to have to paint mine as well to match my red tool boxes!!

Glad to see someone else welding the load path members into those bumper brackets lol. Have you pulled anything with it yet, and if so, how much weight? I was about to do the same thing because I have a 70s mustang gas tank that stops a few inches shy of the frame members and there is limited room. I was planning to triangulate some secondary tubes to take the tongue load but I was going to drop the receiver under the bumper. My 72 F100 sits at normal ride height and I don't need to punch a hole in the bumper, but I really like the idea of hiding it behind the plate so I think I am going to do it. Glad I saw this video. Nice job!

Fantastic idea! Thank you for sharing. Any updates on what you put into the cabinet??

Мир вам, мой дядя, я говорю с вами из Марокко, я хочу спросить вас, пожалуйста, ответьте мне, пожалуйста, мир на вас, мой дядя, я говорю с вами из Марокко, я хочу спросить вас, пожалуйста, ответьте мне, пожалуйста

I had a problem with this relay triggering fans from the Holley. Kept cutting off relay when fans would activate through the Holley . Dunno if anyone else had had this problem

I love the idea, how much does one cost if I buy it from your workshop?