- 557
- 303 859
Group Imaging Channel
Registrace 21. 10. 2007
Video
Trading Card Designer Product Type Fails to open
zhlédnutí 2Před 2 měsíci
Created with Wondershare Filmora
Trading Cards Duplicate Image and Shifted Text
zhlédnutí 1Před 7 měsíci
Trading Cards Duplicate Image and Shifted Text
How to Place an Order forCamper Trading Cards
zhlédnutí 16Před 8 měsíci
Created with Wondershare Filmora
Photographic Baptism Certificates
zhlédnutí 13Před 9 měsíci
An Introduction to our new product, Photographic Baptism Certificates. www.groupimagingphotos.com/landing-page-baptism-certificates
Photographic Baptism Certificates
zhlédnutí 7Před 10 měsíci
An Introduction to our new product, Photographic Baptism Certificates. www.groupimagingphotos.com/homebaptism
How to Order Photo Baptism Certificates
zhlédnutí 23Před 10 měsíci
Tutorial on how to order Photo Baptism Certificates online.
How to Compose Better Group Photos 13 minutes
zhlédnutí 36Před rokem
How to Compose Better Group Photos 13 minutes
How to use FAQ Page on GroupimagingPhotos.com
zhlédnutí 12Před rokem
How to use FAQ Page on GroupimagingPhotos.com
How to see your high resolution images online: High Res Toggle Switch
zhlédnutí 9Před rokem
How to see your high resolution images online: High Res Toggle Switch
New Reference Fields: Line Item Name and Job Name
zhlédnutí 4Před rokem
New Reference Fields: Line Item Name and Job Name
How to Upload Photos 3min Abreviated Version
zhlédnutí 69Před rokem
How to Upload Photos 3min Abreviated Version
How to upload photos to https://photos.groupimaging.com
zhlédnutí 66Před 2 lety
How to upload photos to photos.groupimaging.com
Changeable prototype of 2’x6’ outdoor banner stand
zhlédnutí 74Před 3 lety
Changeable prototype of 2’x6’ outdoor banner stand
how you printes the patter ?
What is called the part that you guys have put on the back of the letters to hang it on the wall
they are called studs
@@groupimaging Hi , I have look for studs every where on amazon or for signage on the web but I could not find this material Could you share a link or a place where I could find these "studs" please thank you again
I found right Terry. They at letter pads www.montroy.com/com/item.php?item_no=11%2F2PAD&item=11%2F2%22+LETTER+SUPPORT+PAD+
Gracias!!!!❤ por fin alguien con una idea nada complicada y fácil de hacer.👍🏻
Amateur
Mind if I ask what you charged for this install?
good
Produk dan pekerjaan yang bagus! Saya Mulyono dari studio Astaka Aditama Jakarta, pengin tahu dan membutuhkan bahan "hard coating eps styrofoam for props". Bisa dibantu kah?, dimana bisa saya dapatkan/beli? Terimakasih.
well done , so happy for your work. what kind of cellecone is it ?
Any idea how to repair a wall full of holes from letters removed on a stucco wall?
What is the heat gun and attachment you are using?
It is a tool from 3M and uses just a standard heat gun. I think the 3m tool is about $400
What kind of hardware is this? Where would I buy these parts?
it is all off the shelf parts. the alumunum is 1.5" sch 40 the holes in the ground are 2" abs black pipe about 24" long the fittings are a product called speed rail from www.hollaender.com/
Nice sign thank you for sharing👍👍👍how thick are the letters?
.250 alum and tapped holes
Any banner could install like this?
Which is the vinyl used? thx.
I think just a standard calendared vinyl. Not made for block. But it worked ok
What machine was used to create the vinyl graphic?
Hp 360
How was this made
what type of vinyl is this ???
How much gap is sufficient for letters Pls say
What kind of feeds and speeds are you using? Also, what type of endmill are you using?
It's an oscillating knife not a router bit (end mill).
any idea if the polyurea comes to be applied by brush?
Sorry, it cures in 10 seconds when part A contacts part B. not possible to hand do it. requires a $25k machine that pressures the chemicals to 2000psi at 165 degrees to then spray out of the gun, then cures after mixing in the nozzle of the gun in less than 10 seconds.
I saw some interview and randomly thought “what does these red carpet/media conferences backdrops printing look like” this is exactly what I was looking for when I looked it up on here!
Nice work sir beautiful design
What machine do U use
Where did you find the post? How long are the segments and how much does it weigh?
We make Tradeshow displays a the posts are a part of our other stands. You would not find this readily. We used 1.25” alum tubing and sewage the ends to 1.125” so the slide into the end of the next pole. The base is 2”x 3/16”x12” aluminum flat bar. We turn the post on a lathe and drill and tap it to screw it to the base from the bottom
Fun video but hard to sit thru without sound or music
Do u do video game charachter cutouts
So this is regular banner material ?? What glue did you use and how long will it stay up? Also fid you remove the staples aftrr install
How to remove this nameplate
You are correct and if that is a fear you can have an usher with gloves hand out all of the servings so no one who is not sterile touches the other cups
Love the disposal part, but I have a problem with the initial pickup. When the people pick up their cup, there is the possibility that they are touching other cups, and one person could reach their entire hand down in there and contaminate the whole bunch.
Awesome 👌
What's the min thickness you can use for the aluminum?
Motion sensor door ...add a motor to the top like at a supermarket.
Every is still touching it.
Very good design scheme, as a board manufacturer, let me learn a lot.
just 2 issues to consider. is it ADA compliant and void the compliance of the existing handle and how will people know how to use it ? most will just grab it ?
You can buy aluminum letters wholesale from these guys, they ship worldwide. www.buysignletters.com/en/Flat-Cut-Aluminum-Letters-Numbers
It is 10 mm. I think I have seen some who double that with two layers of 10mm to add rigidity, but this works fine for the intended purpose.
What is the thickness of the coroplast
What type of lighting were you using to light up these panels from behind?
nice work ... good like
who's puttin ink?
I want that in my back yard instead of a fence
nice, may i know what kind of cloth you use? thanks
We have a 10ft wide Mimaki printer and a 10ft wide Roll to Roll Heat press ($250k for both) and print on transfer paper and then put it in the heat press and transfer the image to a polyester cloth , Aberdeen 6243 Knit Fabric czcams.com/video/Ea8y_XEcSyQ/video.html
is the underbase use original picture without seperation?