Video

I don't really see how the S&B is much, if any, better than the stock setup. The filter and intake point seem similar in size. What is the advantage, exactly?

Does anyone make a cold air intake for the Lincoln continental with the 3.0 ecoboost in it??????

Can't hear a word your saying

MPG after install?

So could you technically just remove the secondary filter and gain some power?

Can u find out for 2020 chevy impala for drop tank

Thank you sir 🫡 exactly what’s needed 🎉

Have had your dry filter on my trucks for combined mileage over 400k miles now between them zero issues! Just ordered a particle separator for my 2024 honda talon fox live valve can't wait!

This is the best option I have seen for under van tank mounting! I will be ordering this. Do you guys have options for fill spouts or recommendations on location for that?

Great instructional video. I'm planning on buying one of these kits. What grill is on that truck? It looks like it has holes for extra air flow on the sides.

Will it perform properly if you have a windshield?

Impressive! 👏🏻👍

Very good tutorial! Thanks for that . Mine just cracked and will be replacing it

Is that smog legal in California?

I just installed these mounts on my 06 F350, and one of them snapped while I was torqueing it down. I'm willing to admit something is my fault it it in fact is. I got no instructions in my box saying not to use air tools. Just wondering if the product was defective or if I did this using air tools.

@SBFilters Thanks for making this video and thank you for committing to helping us with older trucks. I will be purchasing these soon!

Have you put this on the dyno yet? Improvements in HP, torque, MPG?

Are there any issues with the Transit's exhaust pipe heat with the passenger side tank? Does it need some shielding?

Good video, personally I put one boot on the intake plenum manifold and the other boot on the spider/x pipe. then I go in a straight line pushing the boot that is on the spider/x pipe on to the other intake plenum manifold. then I push towards the other boot on the intake and its usually easy.

Why not delete the intake resonator? Give her some real whistle

Thank u for the video half the reason I’m buying one is for the noise so this helps

How do I reset it for it to read the new fuel mileage per tank! I did this on my 2016 shortbed dually yesterday but it still says I only got 386 miles with the new 55 gallon

How does the Mass Air Sensor unplug ? Wire clip was on opposite side I could'nt see pinch and pull did'nt work??

Too bad the wait is so long. I ended up going with FenFab V2 but I wanted to try this.

I have the same problem, tuner says error code P1475. Google says i need my actuator recalibrated. What gives?

Where can i buy it in México?

Thats a pretty beefy intake. Have you noticed a difference on the mpg’s and power and how about your throttle response?

Why is there a strap around the air scoop?

whats the part number on the quick connect tool

Looks like you have the electric side step in the beginning of the video? If so, does this gas tank work with the electric side step installed?

How do you accommodate the parking break components? In your video looks like they have been removed.

Your video doesn't show the parking break linkage or the cable. How do you accomodate the parking breake components?

Sadly still waiting for this to be CARB legal

Thanks for the video. Just bought a 2024 Chevy 3500 DRW. I'm considering buying spacer. I had a 2020 Chevy 2500 before the 3500 and I just cleaned my MAP sensor every other oil change. Have you done any testing to find out how long adding a spacer extend the MAP cleaning interval? Did you disconnect the batteries before disconnecting the MAP harness? I couldn't tell in the video.

Little concerned with the supplied rubber hose getting stuck on the pulleys and belt

I have your cold side and my reason for purchase was preventing the blow out but what is the actual rock solid purpose to install the hot side. It’s the same ford clamp a metal tube with rubber boot. I’m seriously asking because I want one but honestly it’s just because of your logo and wanting it to match but other than that don’t see any benefits

How it is vented? Do you have vent preinstalled, or we utilize 3/4NPT on the top?

Man I can’t wait to get mine, I always run S&b in all my vehicles. I just got another 7.3l with a AIRAID cai and I hate the way it looks, yours looks like it belongs in the engine bay and it keep the air a lot cooler than other on the Market

Love how you answer the I don't want to say stupid questions. You guys rock

I wish the cross member wasn’t such an afterthought.

When will the extra capacity fuel tank for extended cab short beds be available

But is the engine actually flowing 1000cfm?

You’d think from a company as big as you guys there would be a more in depth install……. How to flip the sensor (that should’ve came the other way from the factory) the sizes and tools needed….. send me an intake and I’ll make a more professional in depth install video for you guys.

This was an awesome step by step video!! Love my intake on my 09 jetta 2.0 tdi!

👍👍👍👍👍👍👍👍👍

Yes but how much filtration do you lose.

It is not complicated with sprinter 2500 170 2022. We just bought one and screws do not line up

Dude showed half his statistics said how bad the original was then his s&b did about the same from the first number he’s referring to 542 and just didn’t explain a thing else but switching them out then saying the results. Dude started with stats then by the end said trust me bro😂

Put some in it and see how it works,

Now it sounds like it’s supercharged!