Video

When you put on your turn signal, does it show as amber yellow or white?

How do you like those control arms? Any issues with them?

I got the Rough Country 2.5" shocks and springs lift kit installed along with Rough Country adapters and newer 17" Rubicon wheels and 285/70-17 tires installed and now Around 45-50 mph it shakes so bad the rear view mirror even fell off, any thoughts or ideas to try? JW thanks

Must be nice ❤

Good job with the video. It’s very well explained. My question is did you need the software to remove the IBR errors or to make sure it recognized the IBR?

Looking forward to the differential video. I just purchased new 4.88 gears for my 2.5L TJ because I am tired of not having a usable 5th gear after upgrading to bigger (33") tires.

I really enjoy watching your videos, and they've helped me several times when I've been working on my 99 TJ. I've been curious, though... what is your mechanical background? You do a LOT of stuff right there in your garage/driveway and have a whole BUNCH of tools to work on the vehicles!

Great video and cool hood lift, Steve. Sorry to hear about JJ, and Red. Can’t wait to see the rear diff video, though bummed that you have to make it.

Enjoyed the video, subscribed but have a couple of questions. 1. Is unplugging the computer Not a big deal? Nothing to be concerned about? 2. I have seen replacement motors that are for a one prong (terminal) system. Is that what you have? 3. And lastly, was the new motor supplied with the ground that you put on? Thanks for taling the time to answer. Thanks!!

I like being able to lay the hood all the way back to the windshield. It allows maximum light and maximum room when working under the hood. I have a hood prop and never use it. Thanks for the video tho and stay hydrated in this good ole MS August heatwave 🥵👍🏻

Great video

Love your channel helps me a lot with my 98tj

Thanks for the videos. I am helping my kid learn how to work with tools by helping him rebuild a 97 TJ with the 2.5 liter engine. Been a great project for us and your videos are extremely helpful.

Just ordered one!

Do all 4.0 have a bushing in the pilot bearing I am putting a 97 4.0 auto into a nv3550 but I see the some people use like a bronze bushing and then the pilot bearing and some people don’t have one like you I am somewhat confused

I have never heard of one of these, they seem really cool. Great video, and nice tip with the cardboard.

Cool video. Enjoy Jeep Invasion! Jeeps Jeeps everywhere you look!

I like the struts! Did not know about them…

Hood Assist Jeep TJ:amzn.to/3A6RJVM

Can these motors be bought in the UK

Where did u wire power to

IBR Actuator Motor: amzn.to/3WnTkMy IBR Actuator Motor link 2(In case one link stops working): amzn.to/3HEQHCe Black RTV Sealant: amzn.to/3A2irLx

Got a 06 TJ, had seen this done by another owner. Been wanting to get this done, before my frame goes to hell, guess I'll check my drill bits out and getter done. Thank you much

Good info thanks

On my 2006 TJ, my driver door switch only had two wires, so easy peasy... just wondering what the 3rd wire is for....

So looks like you keep the vehicle running for the whole process?

How long does this take to do? Thanks

Many thanks for making this video. Same thing on my 98 tj

Good job!

How do you do IBR over ride

heey! thanks for this video!! is the u joint in upper shaft the same? the one behind the steering wheel?

I will be replacing all of my brake pads and this video is a great help for those of us that actually have a electronic parking actuator module. This is my baby and so I want to take great care of it when handling sensitive electronic component. The worse thing you or anyone can do is destroying it by not researching it and they just go and start tearing things apart without knowing what can really go south quickly and will cost you an even bigger problem. Thank you very much for providing this great video guide that I have been looking for. These parts aren't cheap, so take great care of them when servicing it yourself. I much rather play it safe then sorry. I just got a recent code for right parking barrage actuator high voltage when I went to use my diagnostic scanner. It detected a problem with the parking brake actuator. Says it needed recalibrate probably because my brake pads are worn out. For now I just clear the code only until I get all the new pads in then I will go ahead and recalibrate it back to manufacturer spec. These electronic parking brake actuator are picky and prone to going out if you use it too often when it is unnecessary on a flat surface. They're only meant to be use temporary when you are parking in a steep incline road. They're not meant to be use all the time on flat surface road. I just found out a hard lesson to never use then unless it is necessary only in steep hill parking and not on flat road that are ground zero level.

My 97 tj's fuel pump quit working today...suks.

Beautiful jeep! Love it...

Great video! Worked perfectly with my 2020 traverse.

Would like to see how you did the wiring on the ring. Getting ready to do the same thing on mine. This looks like a lot of splicing.

The link you mentioned says fit 2.5”-6” lift kit does they fit 2” lifted jeep as well

Watching a year later ...... Thanks I better understand what my problem is.

That is definitely next on my list! My console looks terrible. Can I sand out scratches or will just look worse when painted?

worked perfect

That’s been a dodgy repair before you don’t put washers under the nut on tie rod ends, if you see a washer you know someone has tried to remove the play from the worn out joint before

Thanks for this video. I have a 91 chevy and your video helped me.

Merci beaucoup ❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤

All ways glad for your videos to come out.

Wow! It looks great!

Very nice! This is on my to do list. Having another cup holder and more storage would be sweet! Last weekend I replaced the wiper and turn stalks, Ignition lock, actuator, and switch. Changing the lock wafers to keep my original key looked intimidating but was easy.

Adhesion Promoter:amzn.to/4cN2UB1 Satin Black:amzn.to/4cOmhK3

Great video! Glad to see you back!

That looks real good!

Did you replace the center console lock? Mine will not pop up.