Video

Nice interview Harry! With Kyle, Finn, and you onboard the completion should be very nervous! Three iceboaters from Lake Geneva in a foiling boat, keep your eye on these guys. Sail fast and take chances! Bob Nite495

Interesting Info. Thank you!

Any chance of having someone contact regarding the repair and or replacement of an intermediate mainsail bat car.? Thanks

2.5 MM Punch would be ideal. as the pin is 1/8", an eighth inch Punch gets stuck. I also found if handy to use a 1/16" Pin to use as a guide for re-inserting the roll pin, as they are a little large and seem to remove a little of the plastic. The knob is a terrible design, seems to be designed to fail. The little 1/8" nub that goes into the hole in the spring will snap off sooner than later. I saved my knobs, and drilled a 5/32" hole where it was sheared off, and pushed a 5/32" X 5/8" pin up into the plastic, I think that should hold up better.

Nice. Just ordered one. I appreciate the chill and informative video. I know it’d be cooler and slightly more informative to show it in action on a boat, but I know the reality is that’s 10x the effort… so factory explainer vid works great!

Very concise and to the point. Not a single second wasted. Well done, sir.

New laser sailer here. This was great, thanks! I ended up leaving the tail of the bowline very long and tying another large bowline on it to serve as a handle.

I have first-generation track for the foresail on my boat. Is my only option to get the new captive-bearing system and install as you show at 4:00, or do Harken still produce non-captive bearings cars for the old track?

Not relevant as instructions for the MODEL 7800. Did you forget that? Oh, and the unsecured propane cylinder on the VERY EDGE of a wobbly 1/2" sheet of plywood is both stupid and dangerous.

Will explain later but we have the blue bearing loader system

John Christionson...invented it 🤓

Hard to believe how much more expensive the MK4 is based on how similar they are.

God bless you!

what is the purchase system ration on that kicker system???

Too much talking and repetitive.

I almost got a headache as the image bounced around.

Thank you for creating this amazing opportunity!

Brings tears to my eyes. Bravo Zulu!!!

I am interested in getting a small bat car system for a freedom 21. What number should I call? :)

I could only manage to watch 2 minutes. It's very disturbing needing all those lines for minute performance gains. For goodness sake, just build a better boat that's less complicated.

Lolololololoolololol what do you mean "would be a nightmare to sail"? I'm surprised they are legal! Are that many control lines really that necessary? The only thing capable of sailing that hideous cacophony of lines is an octopus.

This is amazing!

Where i can buy ung harken brands I'm from Philippines and where are you located maybe my aunte can come to your Shop

Very nice 😮😮

Is it an idea to put on some stainless steel triangle on that spot of every boat

We’re u racing with Jim Haussmann ?

Hi, What would your recommend for the luff length of the asymatric spinnaker in relation to the length between the attachement points on the anti-torque cable for a top-down furling system? How many percentage % should the luff length of the sail be longer then the length between the attachement points on the cable, to have a asymatric sail for deep sailing that can still be furled up easily?

Will you make one for 16 mm line?

Thankyou Harken you keep making our lives easier to focus on winning.

finding sensible balance within design goals at odds, good job guys. i was expecting something more like the snub air, by the title ...but it turned out to be a beast of a winch.

Love this. I lived just around that point on the left for 7 years. Managed to crash my Prindle 16' catamaran into the Harken's pier once when I was about 20. He came out and had a good laugh at the situation.

My grantfather did it and i did it as well, it is going so fast! In the Netherlands it was common, now it is rare.

When I see anyone using the back of a screwdriver as a light Mallett you have lost me. You are a butcher of tools. WRONG tool for a basic job! Wouldn't trust you to tie shoelaces correctly. And never near my boat.

Arkea Ultim Challengers uses these winches.

Mine was junk. $2500 down the drain.

how many mm are the pawl springs

from under the shell part rail must be welded or can be installed on top of faired shell ?

Step One : Secure the noisy halyards ‼️

How to exchange Electric Winch System for Hydraulic Winch System on a sailboat?

Supa

Intangible wisdom!

What an awesome interview! Such a great guy!

Go well Herman.

👍

That looked like fun.

Traduction en français ça serait cool 👍

real Legend

This is more of an interview than tour

Thats not a tour

Homie takes a summersault backwards into the cockpit like he planned it