Video

Squaring the side of the base plate on the lathe with the massive overhang looked pretty scary. You are a braver man than I am.

How can this happen? Which lathe is this?

Is it a suppository?

Nice work looks great

Like your vid 🔥🔥

Hey, what brand is that machine?

Top Job, Sir 👌

Excelente trabajo, gracias por compartir todo el contenido

Kkkk é só despeijar o líquido no outro galão, muito trabalho pra nada 😂😂😂😂😂

nice build! seriously! very nice machine work, but i wouldnt recomend using that oil. not just yet. its a virgin pump. there is going to be very small particles of brass and steel. i would mix a honing solution first and run that. then would be okay to use that pump.

I just started working in machine shop don’t know shit but I’m going to and I’m determined! Your a boss

Can you show oil crystelys under pressure?

Where do I get that tap handle?

Good pump for small scale and difficult areas. Nicely done, great job

Impressive build!

Do you know why this pump isn't working at all? You're forgot to spring rollers to external walls. Even in dental maschines it's tiny rotor flaps havs been pushed by 1.5mm dia. springs. Yes, dental drills feeds by compressed air, but excentric rorots are pumps and motors same time.

Do don't know how much id like one them little drill driven pumps handy for moving my waste veg oil from fish & chip shops to run in my vehicle. I didn't know that they use the round vanes instead the flat ones i guess it makes smooth sense that they roll, i wander if they last as long as the vane flat or rectangular vane pumps.

Gostei muito existe hoje ainda em empresas q não dão bomba de repor óleo em redutores pequenos isso iria ajudar muito

Lidl do a 12v pump for £13.99 a bit quicker

Not exactly a revelation, from Engineers heaven!

perfect...thank you so much...

18:43 여기서부터 조립

Супер узор 👍💯👌

You've even demonstrated cavitation in the pump! Well done Sir.

is this manual or cnc? either way insane accuracy good work man

Is that ever cool ❤ nice work. I'll have to try that out!

Good❤

good job 👍

So if you reversed the drill would it work with the same efficiency in the opposite direction ??

If only he showed the pump working in the first few minutes, then the full description of how it works and was made......sigh, dreams.

Fascinating work

That's great, you are a skilled machinist. You could also learn how to open your plastic clamps with a tiny blade/screwdriver. This would be more ecological-friendly and financial-friendly. Peace & prosper. ❤🖖

The same system i saw in some electric fuel pumps...thanks to show how it works

Добрый день. Какой у вас знакомый фрезерный станок - Нгф-110, с вертикальной фрезерной головкой, мне нравится, хорошо работает, тихо. Наверно привод на ВФГ через ремень с движка кинули?

Ого! Ото сосає!

Thank God I have learned to skip ahead. With no details of what you are doing, or how it works, there is no point in watching you make it. I was let down Big time.

So satisfying to watch - much better than the rubbish on tv these days! :)

Производительность, литр/мин.?

Only took $12,000 in machine work.....!

Muy didáctico... Éste sistema de bomba para calefaccionar los salones y dormitorios.... los usaba ''El Titanic''.... trasladando agua caliente desde las calderas del buque.

very nice!

really does the syphoning nice... those, your captions need to be held for a few seconds longer for their information to be digested, almost as bad as Chinese/Japanese martial arts movie TV show , that its either watch or read but not both

This is not a good idea for a liquid pump. This is a typical desigion for a air pump, because the gas between the segments is compressed and reaches the outlet in a compressed state. But liquid does not compress. Therefore, it simply resists compression if it does not find a way out and reduces efficiency. A simple centrifugal impeller is more efficient than this design.

With gears, you get higher pressures and no vibration but a good waste of time.

It is very close to a parasitic pump but without the tubing. I would guess because of the design you could get a pretty accurate and consistant flow rate from it unlike many other pumps. I was wondering why the thing was eccentric in the beginning but it made sense when you put the rolling pins in it at the end. Do you sell something like this?

If I ever owned all those metal machines, I would buy some plans for a mini V8 and spend a year building one. That would be an awesome project that I would love to do in my spare time. I have no idea where I would get plans or the metal but I would be busy for a year learning how to do something with a project I would enjoy. I love the satisfaction of a creation coming alive! But I have no place for the equipment and Im not going to pay for someone else to do it. Maybe one day I will hit the lottery lol. You are doing a great job!

Very good and impressive video and pump. Great appearance too. One can see the rotor work and suck and push oil through just curious to know what pressure it achieved. Splendid job😎👍

I insist, what a genious you are!

La segunda rolinera , la que va pegada al vidrio no hace nada realmente, en corto tiempo esta bomba no funcionara correctamente , lo hara por muy poco tiempo, diseño deficiente.de hecho el ruido del taladro electrico es uno y fijo , y con la bomba va cambiando , no aguantara una hora funcionando sin detenerse , de hecho se nota el cambio de sonido cuando la rolinera falla y se detiene intermitentemente, por lo demas un trabajo de torneria muy bueno.